Gardner Denver AEON PD Grease
H.M.I.S.
Health: 0
Flammability: 1
Material Safety Data Sheet Reactivity: 0
These ratings should be
used only as a part of a fully
implemented H.M.I.S.
program.
Section I - Product Identification
Trade Name and Synonyms Part Numbers:
AEON PD Grease 28H282, 28H283 Health Emergency Phone Number
Safety Department
Manufacturer鈥檚 Name
Gardner Denver, Inc. 217-222-5400
Address
100 Gardner Park Peachtree City, GA 30269
Transport Emergency Phone Number
Product Identification
(800) 424-9300 (CHEMTREC)
Positive Displacement Blower Lubricant
Chemical Names and Synonyms Use or Description
Severe Treat Min. Oils & Additives
Section II - Composition/Information on Ingredients
Substance Name Approx. Wt. %
Zinc Dialkyl Dithiophosphate 1-5
Section III - Chemical and Physical Properties
Appearance: Color:
Grease Green
Odor: Odor Threshold- NE
Mild
ppm:
pH: DMSO Extract, IP- <3, for mineral oil only
NA
346 (WT.%)
Drop Point C (F):
Boiling Point C (F): >246 (475)
>316 (600)
Flash Point C (F): Solubility in Water:
>204 (400) (Estimated for oil, ASTM D-92
(COC))
Flammability Auto Flammability
NE NA
(solids): C (F)
Explosive Oxidizing
NA NA
Properties Properties
Vapor Pressure- Vapor Density:
<0.1 NE
mmHg 20c
Evaporation Rate: Relative Density,
NE 0.901
15/4 C:
Solubility in Water: Partition
Negligible >3.5
Coefficient:
Viscosity at 40 C, Viscosity at 100 C,
>135.0 NE
cSt: cSt:
Pour Point C (F) Freezing Point C
NA NE
(F):
VOC: Note:
<1.00 (Wt. %); 0.083 lbs/gal Most physical properties for oil
component.
NA=Not Applicable NE = Not Established
Section IV - Hazards Identification
Under normal conditions of use, this product is not considered hazardous according to regulatory guidelines.
Emergency Overview: DOT ERG NO. : NA
Green Grease.
POTENTIAL HEALTH Under normal conditions of intended use, this product does not pose a risk to health. Excessive
EFFECTS: exposure may result in eye, skin or respiratory irritation.
Gardner Denver AEON PD Grease
Section V - First Aid Measures
Eye Contact: Flush thoroughly with water. If irritation occurs, call a physician.
Skin Contact: Wash contact areas with soap and water. Remove and clean oil soaked clothing daily and wash
affected area. INJECTION INJURY WARNING: If product is injected into or under the skin, or
into any part of the body, regardless of the appearance of the wound or its size, the individual
should be evaluated immediately by a physician as a surgical emergency. Even though initial
symptoms from high pressure injection may be minimal or absent, early surgical treatment within
the first few hours may significantly reduce the ultimate extent of injury.
Ingestion Not expected to be a problem. Seek medical attention if discomfort occurs. DO NOT INDUCE
VOMITING.
Inhalation Remove from further exposure. If respiratory irritation, dizziness, nausea, or unconsciousness
occurs, seek immediate medical assistance. If breathing has stopped, assist ventilation with
mechanical device or use mouth-to-mouth resuscitation.
Section VI - Fire Fighting Measures
Flash Point: C (F) >204 (400) Estimated for oil, ASTM D-92 (COC)
Flammable Limits (approx. % volume in air)
LEL: NE
UEL: NE
Extinguishing Media: Carbon dioxide, foam, dry chemical and water fog.
Special fire fighting Water or foam may cause frothing. Use water to keep fire exposed containers cool. Water spray
procedures: may be used to flush spills away from exposure. Prevent runoff from fire control or dilution from
entering streams, sewers, or drinking water supply.
Special Protective For fires in enclosed areas, fire fighters must use self-contained breathing apparatus.
Equipment:
Unusual Fire and explosion None
Hazards:
NFPA Ratings: Health: 0, Flammability: 1, Reactivity: 0
Combustion products: Fumes, smoke, carbon monoxide, sulfur oxides, aldehydes and other decomposition products, in
the case of incomplete combustion.
Section VII - Stability and Reactivity
Stability (Thermal, Light, Stable.
Etc.):
Conditions to Avoid: Extreme heat and high energy sources of ignition.
Incompatibility with other Strong oxidizers.
Materials:
Hazardous Decomposition: Product does not decompose at ambient temperatures.
Hazardous Polymerization: Will not occur.
Section VIII - Accidental Release Measures
Notification Procedures: Report spills/releases as required to appropriate authorities. U.S. Coast Guard and EPA
regulations require immediate reporting of spills/releases that could reach any waterway including
intermittent dry creeks. Report spill/release to Coast Guard National Response Center toll free
number (800) 424-8802. In case of accident or road spill notify CHEMTREC (800) 424-9300.
Procedures if material is Land Spill: Shut off source taking normal safety precautions. Take measures to minimize the
released or spilled: effects on ground water. Recover by pumping or contain spilled material with sand or other
suitable absorbent and remove mechanically into containers. If necessary dispose of absorbed
residues as directed in Section XIII.
Water Spill: Confine the spill immediately with booms. Warn other ships in the vicinity. Notify
port and other relevant authorities. Remove from the surface by skimming or with suitable
absorbents. If permitted by regulatory authorities the use of suitable dispersants should be
considered where recommended in local oil spill procedures.
Environmental Precautions: Prevent material from entering sewers, water sources or low lying areas ; advise the relevant
authorities if it has, or if it contaminates soil/vegetation.
Personal Precautions: See section 10.
Gardner Denver AEON PD Grease
Section IX - Handling and Storage
Handling: High pressure injection under the skin may occur due to the rupture of pressurized lines. Always
seek medical attention. No special precautions are necessary beyond normal good hygiene
practices. See Section 10 for additional personal protection advice when handling this product.
Storage: Keep containers closed when not in use. Do not store in open or unlabelled containers. Store
away from strong oxidizing agents and combustible materials. Do not store near heat, sparks,
flame or strong oxidants.
Special Precautions: Prevent small spills and leakages to avoid slip hazard.
Empty Container Empty containers retain residue (liquid and/or vapor) and can be dangerous. DO NOT
Warning: PRESSURIZE, CUT, WELD, BRAZE, SOLDER, DRILL, GRIND OR EXPOSE SUCH
CONTAINERS TO HEAT, FLAME, SPARKS, STATIC ELECTRICITY, OR OTHER SOURCES
OF IGNITION; THEY MAY EXPLODE AND CAUSE INJURY OR DEATH. Do not attempt to refill
or clean container since residue is difficult to remove. Empty drums should be completely
drained, properly bunged and promptly returned to a drum re-conditioner. All containers should
be disposed of in an environmentally safe manner and in accordance with governmental
regulations.
Section X - Exposure Controls/Personal Protection
OCCUPATIONAL EXPOSURE LIMITS:
This product does not contain any components which have recognized exposure limits.
VENTILATION: Use adequate ventilation.
PERSONAL PROTECTIVE EQUIPMENT:
General Considerations:
Eye Protection: Generally eye contact is unlikely with this type of material. If eye contact is likely, safety glasses
with side shields or chemical type goggles should be worn.
Skin Protection If prolonged or repeated skin contact is likely, oil impervious gloves should be worn. Good
personal hygiene practices should always be followed.
Respiratory No special requirements under ordinary conditions of use and with adequate ventilation.
Protection:
Section XI - Toxicological Information
Animal Data: Oral Toxicity (Rats): Practically non-toxic (LD50: greater than 2000 mg/kg). 鈥? Base on testing of
similar products and /or the components.
Dermal Toxicity (rabbits): Practically non-toxic (LD50: greater than 200 mg/kg). 鈥? Based on
testing of similar products and/or the components.
Inhalation Toxicity (Rats): Practically non-toxic (LC50: greater than 5 mg/1). 鈥揃ase on testing of
similar products and/or the components.
Eye Irritation (Rabbits ) : Practically non-irritating (Draize score; greater than 6 but 15 or less). 鈥?
Based on testing of similar products and/or the components.
Skin Irritation (Rabbits ) : Practically non-irritating. (Primary irritation Index: greater than 0.5 but
less than 3). 鈥揃ased on testing of similar products and/or the components.
Other acute toxicity data: Although an acute inhalation study was not performed with this
product, a variety of mineral oils and synthetic base oils, such as those in this product have been
tested. These samples had virtually no effect other than a nonspecific inflammatory response in
the lung to the aerosolized mineral oil. The presence of additives in other tested formulations (in
approximately the same amounts as in the present formulation) did not alter the observed effects.
Subchronic Toxicology No significant adverse effects were found in studies using repeated dermal applications of similar
(Summary) formulations to the skin of laboratory animals for 13 weeks at doses significantly higher than
those expected during normal industrial exposure. The animals were evaluated extensively for
effects of exposure (hematology, serum chemistry, urinalysis, organ weights, microscopic
examination of tissues etc.).
Reproductive Toxicology No teratogenic effects would be expected from dermal exposure, based on laboratory
(Summary) developmental toxicity studies of major components in this formulation and/or materials of similar
composition.
Chronic Toxicology Repeated and/or prolonged exposure may cause irritation to the skin, eyes or respiratory tract.
(Summary) For mineral base oils : Base oils in this product are severely solvent refined and/or severely
hydrotreated. Chronic mouse skin painting studies of severely treated oils showed no evidence
of carcinogenic effects. These results are confirmed on a continuing basis using various
screening methods such as Modified Ames Test, IP-346, and/or other analytical methods. For
synthetic base oils : The base oils in this product have been tested in the Ames assay and other
tests of mutagenicity with negative results. These base oils are not expected to be carcinogenic
with chronic dermal exposures.
Sensitization Not expected to be sensitizing based on tests of this product, components, or similar products.
(Summary)
Gardner Denver AEON PD Grease
Section XII - Ecological Information
Environmental Fate and This product is expected to be inherently biodegradable, as the principal components have been
Effects: shown to degrade at slow to moderate rates. The major components in the formulation show no
aquatic toxicity at 1000 mg/L loading, therefore long-term adverse effects in the aquatic
environment are not expected.
Section XIII - Disposal Considerations
Waste Disposal: Product is suitable for burning in an enclosed, controlled burner for fuel value. Such burning may
be limited pursuant to the Resource Conservation and Recovery Act. In addition, the product is
suitable for processing by an approved recycling facility or can be disposed of at an appropriate
government waste disposal facility. Use of these methods is subject to user compliance with
applicable laws and regulations and consideration of product characteristics at time of disposal.
RCRA Information The unused product, in our opinion, is not specifically listed by the EPA as a hazardous waste (40
CFR, Part 261D), nor is it formulated to contain materials which are listed hazardous wastes. It
does not exhibit the hazardous characteristics of ignitability, corrosivity, or reactivity. The unused
product is not formulated with substances covered by the Toxicity Characteristic Leaching
Procedure (TCLP). However, used product may be regulated.
Section XIV - Transportation Information
Shipping Information: USA DOT: Not regulated by USA DOT.
RID/ADR: Not regulated by RID/ADR.
IMO: Not regulated by IMO.
IATA: Not regulated by IATA.
Section XV - Regulatory Information
US OSHA HAZARD COMMUNICATION STANDARD: When used for its intended purposes, this product is not classified as
hazardous in accordance with OSHA 29 CFR 1910.1200.
EU Labeling: Product is not dangerous as defined by the European Union Dangerous Substances/Preparations Directives. EU
labeling not required.
Governmental Inventory Status: All components comply with TSCA, EINECS/ELINCS and AICS.
U.S. Superfund Amendments and Reauthorization Act (SARA) Title III: This product contains no 鈥淓xtremely Hazardous
Substances鈥?. SARA (311/312) Reportable Hazard Categories : None. This product contains the following SARA (313) Toxic
Release Chemicals:
CAS NUMBER CONC.
CHEMICAL NAME
Phosphorodithoic Acid, O, O-DI 68649-42-3 1.3%
C1-14-Alkyl Esters, Zinc Salts
(2:1) (ZDDP)
This product has been authorized by USDA for use under the following category:
This product is acceptable as a lubricant where there is no possibility of food contact (complies with earlier USDA guidelines for H-2 lubricant
use).
The following product ingredients are cited on the lists below:
CHEMICAL NAME CAS NUMBER LIST CITATIONS
Lithium Hydroxide Monohydrate (0.05%) 1310-66-3 22
Xylenes (0.06%) 1330-20-7 22
Tricresyl Phosphate (>0.01%) 1330-78-5 22
Zinc (Elemental Analysis) (0.18%) 7440-66-6 22
Lithium-Soap Thickener (6.14%) 7620-77-1 22
Zinc Dinonylnaphtalene Sulfonate (0.40%) 28016-00-4 22
Phosphorodithoic Acid, O, O-DI C1-14-Alkyl 68649-42-3 18, 20, 21, 22, 24, 25
Esters, Zinc Salts (2:1) (ZDDP) (1.29%)
Fatty Acids, C16-22, Lithium Salts (0.76%) 68783-36-8 22
REGULATORY LISTS SEARCHED
1=ACGIH ALL 6=IARC 1 11=TSCA 4 16=CA P65 CARC 21=LA RTK
2=ACGIH A1 7=IARC 2A 12-TSCA 5a2 17-CA P65 REPRO 22=MI293
3=ACGIH A2 8=IARC 2B 13=TSCA 5E 18=CA RTK 23=MN RTK
4=NTP CARC 9=OSHA CARC 14=TSCA 6 19-FL RTK 24=NJ RTK
5=NTP SUS 10=OSHA Z 15=TSCA 12B 20=IL RTK 25=PA RTK
Code key: CARC=carcinogen; SUS=suspected carcinogen; REPRO 鈥? Reproductive 26=RI RTK
Gardner Denver AEON PD Grease
Section XVI - Other Information
USE: Lithium Complex Grease
Note: Products are not formulated to contain PCBS.
Health studies are not shown that many hydrocarbons pose potential human health risks which may vary from person to person.
Information provided on this MSDS reflects intended use. This product should not be used for other applications. In any case, the
following advice should be considered:
INDUSTRIAL LABEL
Under normal conditions of intended use, this product does not pose a risk to health. Excessive exposure may result in eye, skin or
respiratory irritation. Always observe good hygiene measures. First Aid: Wash skin with soap and water. Flush eyes with water. If
overcome by fumes or vapor, remove to fresh air. If ingested do not induce vomiting. If symptoms persist seek medical assistance.
Read and understand the MSDS before using this product.
APDG-00-2003
|