H.M.I.S.
Health: 1
Flammability: 1
Material Safety Data Sheet Reactivity: 0
Personal Protection: B
These ratings should be
used only as a part of a
fully implemented H.M.I.S.
program.
Section I - Product Identification
Health Emergency Phone Number
Trade Name and Synonyms Part Numbers:
P12906A,P12907A,28H166,28H167
RotorLub 4000 (815) 875-3321
Safety Department
Manufacturer鈥檚 Name
Code: 490-020,
Champion On the DSL On TSCA List
RotorLub
Transport Emergency Phone Number
Address
1301 North Euclid Avenue, Princeton, IL 61356 (800) 424-9300 (CHEMTREC)
Product Identification
Lubrication of air and inert gas compressors of the reciprocating, rotary screw, and rotary vane types. This compressor oil
should NEVER be used in equipment compressing pure oxygen.
Section II - Composition and Information on Ingredients
Exposure Limits (ACGIH)
Name CAS # % (V/V) TLV-TWA (8 h) STEL CEILING
Not
3 3
Severely hydrotreated paraffinic oil and additives Mixture 100 5 mg/m (oil mist) 10 mg/m (oil mist) Established
Manufacturer
Recommendation: Not applicable
Other Exposure Limits: Consult local, state, provincial or territory authorities for acceptable exposure limits.
Section III - Hazards Identification
Non irritating to slight transient irritation to skin and eyes, but no permanent damage. This product
Potential Health Effects:
has a low vapor pressure and is not expected to present an inhalation exposure at ambient
conditions. Upon heating to high temperatures, or mechanical actions which may produce vapors
or mists, inhalation of this product may cause irritation of the breathing passages. Low toxicity on
ingestion. Has laxative effect. For more information, refer to Section 11.
Section IV - First Aid Measures
Check for and remove any contact lenses. DO NOT use an eye ointment. IMMEDIATELY flush eyes
Eye Contact:
with running water for at least 15 minutes, keeping eyelids open. Seek medical attention.
Skin Contact: Remove contaminated clothing - launder before reuse. Wash gently and thoroughly the
contaminated skin with running water and non-abrasive soap. Discard saturated leather articles.
Seek medical attention.
Inhalation: Evacuate the victim to a safe area as soon as possible. Allow the victim to rest in a well ventilated
area. Administer oxygen if available. If the victim is not breathing, perform mouth-to-mouth
resuscitation. If resuscitation is required, physician assessment is mandatory.
Ingestion: DO NOT induce vomiting because of danger of aspirating liquid into lungs. Force fluids. Activated
charcoal tablets.
Not available.
Note to physician:
Section V - Fire-Fighting Measures
Flammability: May be combustible at high Flammable Limits: Not available
temperature.
Flash Points: OPEN CUP: 246潞C (474.8潞F) Auto-Ignition Temperature: >350潞C (662潞F)
(Cleveland)
Low fire hazard. This material must
Fire Hazards in Explosion Hazards in Do not cut, weld, heat, drill, or
be heated before ignition will occur.
Presence of Various Presence of Various pressurize empty container.
Avoid contact with strong oxidizing
Substances: Substances: Containers may explode in
agents, including peroxides, heat of fire.
chlorine, and strong acids.
Products of Carbon oxides (CO, CO2), nitrogen oxides (NOx), sulfur oxides (SOx), phosphorous compounds (POx),
Combustion: smoke and irritating vapors as products of incomplete combustion.
Fire Fighting Media and NAERG96, GUIDE 171, Substances (low to moderate hazard). If tank, rail car, or tank truck is
Instructions: involved in a fire, ISOLATE for 800 meters (0.5 mile) in all directions; also, consider initial
evacuation for 800 meters (0.5 mile) in all directions. Shut off fuel to fire if it is possible to do so
without hazard. If this is impossible, withdraw from area and let fire burn out under controlled
conditions. Withdraw immediately in case of rising sound from venting safety device or any
discoloration of tank due to fire. Cool containing vessels with water jet in order to prevent pressure
build-up, autoignition, or explosion. SMALL FIRE: use DRY chemicals, CO2, water spray or foam.
LARGE FIRE: use water spray, fog or foam. For small outdoor fires, which may be easily
extinguished with a portable fire extinguisher, use of a SCBA may not be required. Respiratory and
eye protection required for fire fighting personnel. A self-contained breathing apparatus (SCBA)
should be used for all indoor fires and any significant outdoor fires.
Section VI - Accidental Release Measures
Material Release NAERG96, GUIDE 171, Substances (low to moderate hazard). ELIMINATE ALL IGNITION
SOURCES. Avoid contact. Stop leak if without risk. Contain spill. Absorb with inert absorbents, dry
or Spill:
clay, or diatomaceous earth. Avoid inhaling dust of diatomaceous earth for it may contain silica in
very fine particle size, making this a potential respiratory hazard. Place used absorbent in closed
metal containers for later disposal or burn absorbent in a suitable combustion chamber, DO NOT
FLUSH TO SEWERS, STREAMS, OR OTHER BODIES OF WATER. Check with applicable jurisdiction
for specific disposal requirements of spilled material and empty containers. Notify the appropriate
authorities immediately.
Section VII - Handling and Storage
Handling: Avoid inhalation and skin contact especially when handling used oil. Keep away from sources of
ignition. DO NOT reuse empty containers without commercial cleaning or reconditioning. Practice
good personal hygiene. Wash hands after handling and before eating. Launder work clothes
frequently. Discard saturated leather goods.
Storage: Store in tightly closed containers in cool, dry, isolated, well-ventilated area, and away from
incompatibles.
Section VIII - Exposure Controls/Personal Protection
Engineering Controls: For normal application, special ventilation is not necessary. If user鈥檚 operations generate vapors or
mist, use ventilation to keep exposure to airborne contaminants below the exposure limit. Make-up
air should always be supplied to balance air removed by exhaust ventilation. Ensure that eyewash
station and safety shower are close to work-station.
Personal Protection: The selection of personal protective equipment varies, depending upon conditions of use.
Eyes Eye protection (i.e., safety glasses, safety goggles and/or face shield) should be determined based
on conditions of use. If product is used in an application where splashing may occur, the use of
safety goggles and/or a face shield should be considered.
Body Wear appropriate clothing to prevent skin contact. As a minimum, long sleeves and trousers
should be worn.
Respiratory Where concentrations in air may exceed the occupational exposure limits given in Section 2 (and
those applicable to your area) and where engineering, work practices or other means of exposure
reduction are not adequate, NIOSH approved respirators may be necessary to prevent
overexposure by inhalation.
Hands Wear appropriate chemically protective gloves. When handling hot product ensure gloves are heat
resistant and insulated.
Feet Wear appropriate footwear to prevent product from coming in contact with feet and skin.
Section IX - Physical and Chemical Properties
Physical State and 46.6 cSt @ 40潞C (104潞F),
Appearance: Liquid (Viscous Liquid) Viscosity: 7.0 cSt @ 100潞C (212潞F), VI=107
Color: Green Pour Point: -33潞C
Odor: Mild petroleum oil like. Softening Point: Not applicable
Odor Threshold: Not Available Dropping Point: Not applicable
Boiling Point: Not Available Penetration: Not applicable
Density: 0.8656 kg/L @ 15潞C (59潞F) Oil/Water Dist. Coeff.: Not available
Vapor Density: Not available Ionicity (in water): Not available
Vapor Pressure: Negligible at ambient Dispersion Properties: Not available
temperature and pressure.
Volatility: Non-volatile Solubility: Insoluble in water
Section X - Stability and Reactivity
Corrosivity: Copper corrosion, 3h, 100潞C (ASTM D0130): 1a
Stability: The product is stable under normal handling Hazardous Will not occur under normal
and storage conditions. Polymerization: working conditions.
Incompatible Reactive with oxidizing agents, reducing Decomposition May release COx, POx, NOx,
Substances/Conditions agents, acids, and alkalis. Products: methacrylate monomers,
to Avoid: smoke and irritating vapors
when heated to
decomposition.
Section XI - Toxicological Information
Routes of Entry: Eye contact, inhalation, ingestion, skin contact
Acute Lethality: Based on toxicity of components:
Acute oral toxicity (LD50): >5000 mg/kg (rat)
Acute dermal toxicity (LD50): >2000 mg/kg (rabbit)
Acute inhalation toxicity (LD50): >2500 mg/m 3/4h (rat)
Chronic or Other Toxic Effects:
Dermal Route: Prolonged or repeated contact may cause skin irritation characterized by dermatitis or
oil acne.
Inhalation Route: Negligible breathing hazard at normal temperatures (up to 38潞C) or recommended
blending temperatures. Elevated temperatures or mechanical action may form vapors,
mists, or fumes. Inhalation of oil mists or vapors from hot oil may cause irritation of the
upper respiratory tract.
Oral Route: Low toxicity; has laxative effect.
Eye Irritation/Inflammation: Repeated or prolonged contact may produce eye irritation, but no permanent damage.
Immunotoxicity: Not available
Skin Sensitization: This product is not expected to be a skin sensitizer, based on the available data and the
known hazards of the components.
Respiratory Tract Sensation: This product is not expected to be a respiratory tract sensitizer, based on the available
data and the known hazards of the components.
Mutagenic: Based on actual test results of base oils and results of similar products, severely
hydrotreated base oils give negative results when tested for: (a) Salmonella
Typhimurium TA98 using the Modified Ames Assay for Petroleum Product; (b)
Salmonella-Escherichia coli/Mammalian-Microsome Reverse Mutation Assay (Ames
test) with a Confirmatory Assay; (c) Structural Chromosomal Aberrations in Chinese
Hamster Ovary (CHO) Cells.
Reproductive Toxicity: This product is not expected to be a reproductive hazard, based on the available data
and the known hazards of the components.
Teratogenicity/Embryotoxicity: This product is not expected to be a teratogen or an embryotoxin, based on the
available data and the known hazards of the components.
Carcinogenicity (ACGIH): This product is not known to contain any chemicals at reportable quantities that are
listed as A1 or A2 carcinogens by ACGIH.
Carcinogenicity (IARC): This product is not known to contain any chemicals at reportable quantities that are
listed as group 1, 2A or 2B carcinogens by IARC.
Carcinogenicity (NTP) This product is not known to contain any chemicals at reportable quantities that are
listed as carcinogens by NTP.
Carcinogenicity (IRIS) Not available
Carcinogenicity (OSHA) This product is not known to contain any chemicals at reportable quantities that are
listed as carcinogens by OSHA.
Other Considerations: No additional Remark
Section XII - Ecological Information
Not available
Environmental Fate: Not available Persistence/Bioaccumulation
Potential:
BOD5 and COD: Not available Products of Biodegradation: Not available
Additional Remarks: No additional remark
Section XIII - Disposal Considerations
Waste Disposal: Spent/used waste oil may meet the requirements of a hazardous waste. Consult your local or regional
authorities. Preferred waste management priorities are (1) recycle or reprocess; (2) incineration with energy
recovery; (3) disposal at licensed waste disposal facility. Ensure that disposal or reprocessing is in
compliance with government requirements and local disposal regulations.
Section XIV - Transport Information
DOT Classification: Not a DOT controlled material Special Provisions for Transport: Not applicable
(United States)
Section XV - Regulatory Information
Other Regulations: This product is acceptable for use under the provisions of WHMIS-CPR. All components of this
formulation are listed on the CEPA-DSL (Domestic Substances List). All components of this
formulation are listed on the US EPA-TSCA Inventory. All components of this formulation are listed
on EINECS or exempt. This product has been classified in accordance with the hazard criteria of
the Controlled Products Regulations (CPR), and the MSDS contains all of the information required
by the CPR. Please contact Product Safety for more information.
DSD/DPD (EEC): Not evaluated.
WHMIS (Canada): Not controlled.
HMIS (U.S.A.) NFPA (U.S.A.) Rating
1 Health Hazard 0 Insignificant
Fire Hazard
1
1 Fire Hazard 1 Slight
1 0
0 Reactivity 2 Moderate
Health Reactivity
b Personal Protection 3 High
4 Extreme
Specific Hazard
ADR (Europe) Not evaluated for European TDG (Canada)
(Pictograms) transport. (Pictograms)
Section XVI - Other Information
Available upon request
References:
Glossary: HCS - Hazardous Communication System
ACGIH - American Conference of Governmental Industrial Hygienists HMIS - Hazardous Material Information System
ASTM - American Society for Testing and Materials IARC - International Agency for Research on Cancer
ADR - Agreement on Dangerous Goods by Road (Europe) IRIS - Integrated Risk Information System
BOD5 - Biological Oxygen Demand in 5 Days LD50/LC50 - Lethal Dose/Concentration Kill 50%
CAN/CGA B149.2 - Propane Installation Code LDLo/LCLo - Lowest Published Lethal Dose/Concentration
CAS - Chemical Abstract Services NAERG=96 - North American Emergency Response Guide Book (1996)
CEPA - Canadian Environmental Protection Act NFPA - National Fire Prevention Association
CERCLA - Comprehensive Environmental Response, Compensation and NIOSH - National Institute for Occupational Safety & Health
Liability Act NPRI - National Pollutant Release Inventory
CFR - Code of Federal Regulations NSNR 鈥? New Substances Notification Regulations (Canada)
CHIP - Chemical Hazard Information and Packaging Approved Supply List NTP - National Toxicology Program
COD - Chemical Oxygen Demand OSHA - Occupational Safety & Health Administration
COD5 鈥? Chemical Oxygen Demand in 5 days PEL - Permissible Exposure Limit
CPR - Controlled Products Regulation RCRA - Resource Conservation and Recovery Act
DOT - Department of Transportation (U.S.A.) SARA - Superfund Amendments and Reorganization Act
DSCL - Dangerous Substances Classification and Labeling (Europe) SD - Single Dose
DSD/DPD - Dangerous Substance or Dangerous Preparations Directives STEL - Short Term Exposure Limit (15 minutes)
(Europe) TDG - Transportation Dangerous Goods (Canada)
DSL - Domestic Substance List TDLo/TCLo - Lowest Published Toxic Dose/Concentration
EEC/EU - European Economic Community/European Union TLm - Median Tolerance Limit
EINECS - European Inventory of Existing Commercial Chemical TLV-TWA - Threshold Limit Value - Time Weighted Average
Substances TSCA - Toxic Substances Control Act
EPCRA - Emergency Planning and Community Right-To-Know Act USEPA - United States Environmental Protection Agency
FDA - Food and Drug Administration USP - United States Pharmacopoeia
FIFRA - Federal Insecticide, Fungicide, and Rodenticide Act WHMIS - Workplace Hazardous Material Information System
To the best of our knowledge, the information contained herein is accurate. However, neither the above named supplier nor any of its subsidiaries
assumes any liability whatsoever for the accuracy or completeness of the information contained herein. Final determination of suitability of any
material is the sole responsibility of the user. All materials may present unknown hazards and should be used with caution. Although certain hazards are
described herein, we cannot guarantee that these are the only hazards that exist.
Prepared by the Product Specialist, Aftermarket
September 2002
|