MATERIAL SAFETY DATA SHEET
Sikaflex庐 2C, NS & SL - Part B
HMIS
HEALTH *2
FLAMMABILITY 2
REACTIVITY 0
C
PERSONAL PROTECTION
1. Product And Company Identification
Supplier Manufacturer
Sika Corporation Sika Corporation
201 Polito Ave 201 Polito Ave
Lyndhurst, NJ 07071 Lyndhurst, NJ 07071
Company Contact: EHS Department Company Contact: EHS Department
Telephone Number: 201-933-8800 Telephone Number: 201-933-8800
FAX Number: 201-933-9379 FAX Number: 201-933-9379
Web Site: www.sikausa.com Web Site: www.sikausa.com
Supplier Emergency Contacts & Phone Number Manufacturer Emergency Contacts & Phone Number
CHEMTREC: 800-424-9300 CHEMTREC: 800-424-9300
INTERNATIONAL: 703-527-3887 INTERNATIONAL: 703-527-3887
Issue Date: 05/02/2007
Product Name: Sikaflex庐 2C, NS & SL - Part B
CAS Number: Not Established
Chemical Family: Polyurethane
MSDS Number: 4095
Product Code: 0464140
2. Composition/Information On Ingredients
Ingredient CAS Percent Of
Name Number Total Weight
POLYISOCYANATE PREPOLYMER mixture
XYLENE (MIXED ISOMERS) 1330-20-7 5 - 10
3. Hazards Identification
Eye Hazards
Causes eye irritation.
Skin Hazards
May cause skin irritation. Prolonged and/or repeated skin contact may cause an allergic reaction/sensitization.
Ingestion Hazards
May be harmful if swallowed.
Inhalation Hazards
May cause nose, throat, and lung irritation. May cause respiratory tract irritation. May cause an allergic respiratory
reaction / sensitization after prolonged or repeated contact. Reports have associated repeated and prolonged
Page 1 of 5
MATERIAL SAFETY DATA SHEET
Sikaflex庐 2C, NS & SL - Part B
3. Hazards Identification - Continued
Inhalation Hazards - Continued
exposure to some of the chemicals in this product with permanent brain, liver, kidney, and Central Nervous
System damage. Headaches and dizziness may result.
4. First Aid Measures
Eye
In case of contact, hold eyelids apart and immediately flush eyes with plenty of water for at least 15 minutes. Get
medical attention immediately.
Skin
In case of contact, immediately flush skin with soap and plenty of water. Get medical attention immediately if
irritation (redness, rash, blistering) develops and persists.
Ingestion
If victim is fully conscious, give one or two cups of water or milk to drink. Never give anything by mouth to an
unconscious victim. Call a physician or a poison control center immediately.
Inhalation
Remove to fresh air. If not breathing, give artificial respiration, seek medical attention.
5. Fire Fighting Measures
Flash Point: 112 掳F
Autoignition Point: N/AV 掳F
Lower Explosive Limit: N/AV
Upper Explosive Limit: N/AV
Fire And Explosion Hazards
Combustible liquid. During a fire, irritating and/or toxic gases and aerosols from the decomposition/combustion
products may be present.
Extinguishing Media
In case of fire, use water spray (fog) foam, dry chemical, or CO2.
Fire Fighting Instructions
In the event of a fire, firefighters should wear full protective clothing and NIOSH-approved self-contained
breathing apparatus with a full facepiece operated in the pressure demand or other positive pressure mode.
6. Accidental Release Measures
Eliminate all ignition sources. Use appropriate Personal Protective Equipment (PPE). Absorb and/or contain spill with
inert materials (e.g. sand, vermiculite) and then place in appropriate container. For large spills, use water spray to
disperse vapors. Prevent runoff from entering waterways or sewers.
7. Handling And Storage
Handling And Storage Precautions
Keep out of reach of children. Not for internal consumption.
Handling Precautions
Keep away from heat, sparks, flame, and other sources of ignition (i.e., pilot lights, electric motors, and static
electricity).
Storage Precautions
Store at 32F min. - 122F max. Ideal storage temperature 50-80F. If closed container is exposed to heat,
pressure can build up. If moisture enters container, pressure may build up due to reaction. Store in cool, dry
area in tightly closed containers, away from sparks and open flames.
Page 2 of 5
MATERIAL SAFETY DATA SHEET
Sikaflex庐 2C, NS & SL - Part B
7. Handling And Storage - Continued
Work/Hygienic Practices
Wash thoroughly with soap and water after handling.
8. Exposure Controls/Personal Protection
Engineering Controls
Use of a system of local and/or general exhaust is recommended to keep employee below applicable exposure
limits. Refer to the current edition of "Industrial Ventilation: A Manual of Recommended Practice" published by
the American Conference of Governmental Industrial Hygienists for information on the design, installation, use,
and maintenance of exhaust systems.
Eye/Face Protection
Faceshield over safety glasses or goggles.
Skin Protection
Chemical-resistant gloves. Lab coat or other work clothing to prevent skin exposure. Launder before reuse.
Respiratory Protection
A respirator protection program that meets 29 CFR 1910.134 requirement must be followed whenever workplace
conditions warrant a respirator's use. In areas where the Permissible Exposure Limits are exceeded, use a
properly fitted NIOSH-approved respirator.
Other/General Protection
Wash thoroughly after handling.
Ingredient(s) - Exposure Limits
XYLENE (MIXED ISOMERS)
ACGIH TLV-STEL 150 ppm
ACGIH TLV-TWA 100 ppm
OSHA PEL-TWA 100 ppm
9. Physical And Chemical Properties
Appearance
Clear liquid
Odor
Aromatic Odor
Chemical Type: Mixture
Physical State: Liquid
Specific Gravity: 1.02
Percent Volatiles: 9.0
Packing Density: 8.5 pounds/gallon
Vapor Density: > AIR
Evaporation Rate: Slower than ether
VOC content: Part B: 92 g/l
For VOC Content of the A & B component mixed, please see the appropriate Part A MSDS.
10. Stability And Reactivity
Stability: Stable
Hazardous Polymerization: Will not occur
Conditions To Avoid (Stability)
Open flame, heat
Page 3 of 5
MATERIAL SAFETY DATA SHEET
Sikaflex庐 2C, NS & SL - Part B
10. Stability And Reactivity - Continued
Incompatible Materials
Water, Alcohols and Amines
Hazardous Decomposition Products
CO, CO2, Oxides of Nitrogen
11. Toxicological Information
No Data Available...
12. Ecological Information
No Data Available...
13. Disposal Considerations
Dispose in accordance with applicable federal, state and local government regulations. Waste generators must
determine whether a discarded material is classified as a hazardous waste. USEPA guidelines for the classification
determination are listed in 40 CFR Parts 261.3. Additionally, waste generators must consult state and local hazardous
waste regulations to ensure complete and accurate classification.
14. Transport Information
Proper Shipping Name
Ground Transport - Not Regulated by the USDOT (per 49 CFR 173.150(f))
Air, Vessel Transport - Flammable Liquids, N.O.S, (Xylene), 3, UN1993, PG III
Additional Shipping Paper Description
Note: This product is not packaged for air transport.
15. Regulatory Information
U.S. Regulatory Information
All ingredients of this product are listed or are excluded from listing under the U.S. Toxic Substances Control Act
(TSCA) Chemical Substance Inventory.
SARA Hazard Classes
Acute Health Hazard
Chronic Health Hazard
Fire Hazard
SARA Title III - Section 313 Supplier Notification
This product contains the following toxic chemicals that are subject to the reporting requirements of section 313 of
the Emergency Planning and Community Right-To-Know Act (EPCRA) of 1986 and of 40 CFR 372.
XYLENE (MIXED ISOMERS) (1330-20-7) 5 - 10 %
This information must be included on all MSDSs that are copied and distributed for this material.
Ingredient(s) - U.S. Regulatory Information
XYLENE (MIXED ISOMERS)
SARA Title III - Section 313 Form "R"/TRI Reportable Chemical
SARA - Acute Health Hazard
SARA - Chronic Health Hazard
SARA - Fire Hazard
Ingredient(s) - State Regulations
XYLENE (MIXED ISOMERS)
New Jersey - Workplace Hazard
Page 4 of 5
MATERIAL SAFETY DATA SHEET
Sikaflex庐 2C, NS & SL - Part B
15. Regulatory Information - Continued
Ingredient(s) - State Regulations - Continued
New Jersey - Environmental Hazard
New Jersey - Special Hazard
Pennsylvania - Workplace Hazard
Pennsylvania - Environmental Hazard
Massachusetts - Hazardous Substance
New York City - Hazardous Substance
16. Other Information
HMIS Rating
Health: *2
F i re : 2
Reactivity: 0
PP E: C
Revision/Preparer Information
MSDS Preparer: EHS Department
This MSDS Supercedes A Previous MSDS Dated: 08/11/2006
Disclaimer
The information contained in this Material Safety Data Sheet applies only to the actual Sika Corporation ("Sika")
product identified and described herein. This information is not intended to address, nor does it address the use
or application of the identified Sika product in combination with any other material, product or process. All of the
information set forth herein is based on technical data regarding the identified product that Sika believes to be
reliable as of the date hereof. Prior to each use of any Sika product, the user must always read and follow the
warnings and instructions on the product's current Technical Data Sheet, product label and Material Safety Data
Sheet for each Sika product, which are available at web site and/or telephone number listed in Section 1 of this
MSDS.
SIKA MAKES NO WARRANTIES EXPRESS OR IMPLIED AND ASSUMES NO LIABILITY ARISING FROM THIS
INFORMATION OR ITS USE. SIKA SHALL NOT BE LIABLE UNDER ANY LEGAL THEORY FOR SPECIAL OR
CONSEQUENTIAL DAMAGES AND SHALL NOT BE RESPONSIBLE FOR THE USE OF THIS PRODUCT IN A
MANNER TO INFRINGE ON ANY PATENT OR ANY OTHER INTELLECTUAL PROPERTY RIGHTS HELD BY
OTHERS.
All sales of Sika products are subject to its current terms and conditions of sale available at www.sikacorp.com or
201-933-8800.
SIKA CORPORATION
Printed Using MSDS Generator鈩? 2000
Page 5 of 5
|