MATERIAL SAFETY DATA SHEET
Sikadur Combiflex Kit - Part C
HMIS
HEALTH *3
FLAMMABILITY 2
REACTIVITY 0
H
PERSONAL PROTECTION
1. Product And Company Identification
Supplier Manufacturer
Sika Corporation Sika Corporation
201 Polito Ave 201 Polito Ave
Lyndhurst, NJ 07071 Lyndhurst, NJ 07071
Company Contact: EHS Department Company Contact: EHS Department
Telephone Number: 201-933-8800 Telephone Number: 201-933-8800
FAX Number: 201-933-9379 FAX Number: 201-933-9379
Web Site: www.sikausa.com Web Site: www.sikausa.com
Supplier Emergency Contacts & Phone Number Manufacturer Emergency Contacts & Phone Number
CHEMTREC: 800-424-9300 CHEMTREC: 800-424-9300
INTERNATIONAL: 703-527-3887 INTERNATIONAL: 703-527-3887
Issue Date: 02/18/2004
Product Name: Sikadur Combiflex Kit - Part C
CAS Number: 1330-20-7
Chemical Family: Solvent Activator
MSDS Number: 3091
Product Code: 0663390
2. Composition/Information On Ingredients
Ingredient CAS Percent Of
Name Number Total Weight
XYLENE (MIXED ISOMERS) 1330-20-7 90 - 100
3. Hazards Identification
Eye Hazards
May cause temporary discomfort or irritation to the eye.
Skin Hazards
Irritating to the skin causing a burning sensation, redness and/or swelling. Prolonged or repeated skin contact
can cause defatting and drying of teh skin which may result in a burning sensation and a dried, cracked
apprearance.
Ingestion Hazards
May be harmful if swallowed.
Page 1 of 6
MATERIAL SAFETY DATA SHEET
Sikadur Combiflex Kit - Part C
3. Hazards Identification - Continued
Inhalation Hazards
Breathing of high vapor concentrations may cause central nervous system (CNS) depression resulting in
dizziness, light-headedness, headache, nausea and loss of coordination. Continued inhalation may result in
unconsciousness and death. Vapors expected to be slightly irritating. Prolonged and repeated exposures to high
concentrations may cause hearing loss.
4. First Aid Measures
Eye
In case of contact, hold eyelids apart and immediately flush eyes with plenty of tepid water for at least 15 minutes.
Get medical attention immediately if irritation develops and persists.
Skin
In case of contact, immediately flush skin with soap and plenty of tepid water for at least 15 minutes. Get medical
attention immediately if irritation (redness, rash, blistering) develops and persists.
Ingestion
If swallowed, do not induce vomiting unless directed to do so by medical personnel. If victim is fully conscious,
give one or two cups of water or milk to drink. Never give anything by mouth to an unconscious victim. Seek
medical attention immediately.
Inhalation
Remove to fresh air. If not breathing, give artificial respiration, seek medical attention.
5. Fire Fighting Measures
Flash Point: 79 掳F 26 掳C
Flash Point Method: TOC
Autoignition Point: N/AV 掳F
Flammability Class: FLM
Lower Explosive Limit: 1%
Upper Explosive Limit: 7%
Fire And Explosion Hazards
FLAMMABLE. Vapors are flammable and heavier than air. Vapors may travel across the ground and reach
remote ignition sources causing a flashback fire danger.
Extinguishing Media
In case of fire, use water spray (fog) foam, dry chemical, or CO2. Do not use a direct stream of water. Material
will float and can be re-ignited on surface of water.
Fire Fighting Instructions
In the event of a fire, firefighters should wear full protective clothing and NIOSH-approved self-contained
breathing apparatus with a full facepiece operated in the pressure demand or other positive pressure mode.
6. Accidental Release Measures
Eliminate all ignition sources. Use appropriate Personal Protective Equipment (PPE). Absorb and/or contain spill with
inert materials (e.g. sand, vermiculite) and then place in appropriate container. For large spills, use water spray to
disperse vapors. PRevent runoff from entering waterways or sewers.
7. Handling And Storage
Handling And Storage Precautions
Do not taste or swallow. Avoid contact with eyes, skin and clothing. Wash thoroughly after handling.
Page 2 of 6
MATERIAL SAFETY DATA SHEET
Sikadur Combiflex Kit - Part C
7. Handling And Storage - Continued
Handling Precautions
Keep away from heat, sparks and flame. Extinguish pilot lights, cigarettes and turn off other sources of ignition
prior to use and until all vapors have dissipated. Wash with soap and water before eating, drinking, smoking,
applying cosmetics, or using toilet facilities. Launder contaminated clothing before reuse.
Storage Precautions
Keep containers closed when not in use.
Work/Hygienic Practices
Wash thoroughly with soap and water after handling.
8. Exposure Controls/Personal Protection
Engineering Controls
Use of a system of local and/or general exhaust is recommended to keep employee below applicable expsoure
limits. Refer to the current edition of "Industrial Ventilation: A Manual of Recommended Practice" published by
the American Conference of Governmental Industrial Hygienists for information on the design, installation, use,
and maintenance of exhaust systems.
Eye/Face Protection
Safety glasses with side shields or goggles.
Skin Protection
Chemical-resistant gloves. Lab coat or other work clothing to prevent skin exposure (Long sleeve shirt and long
pants). Launder before reuse.
Respiratory Protection
A respirator protection program that meets 29 CFR 1910.134 requirement must be followed whenever workplace
conditions warrant a respirator's use. In areas where the Permissible Exposure Limits are exceeded, use a
properly fitted NIOSH-approved respirator.
Ingredient(s) - Exposure Limits
XYLENE (MIXED ISOMERS)
ACGIH TLV-STEL 150 ppm
ACGIH TLV-TWA 100 ppm
OSHA PEL-TWA 100 ppm
9. Physical And Chemical Properties
Appearance
Clear Liquid
Odor
Aromatic Odor
Chemical Type: Mixture
Physical State: Liquid
Boiling Point: 279 - 289 掳F
Specific Gravity: 0.76 @ 60F
Vapor Pressure: 6mmHg @ 68F
Vapor Density: 3.7 [Air=1]
Solubility: Negligible
Evaporation Rate: 0.7 [vs. n-Butyl Acetate = 1]
VOC Content: 7.3 pounds/gal @ 60F
Page 3 of 6
MATERIAL SAFETY DATA SHEET
Sikadur Combiflex Kit - Part C
10. Stability And Reactivity
Stability: Stable
Hazardous Polymerization: Will not occur
Conditions To Avoid (Stability)
Prevent vapor accumulation. Avoid heat, sparks, open flames and other ignition sources.
Hazardous Decomposition Products
Carbon Dioxide, Carbon Monoxide
Conditions To Avoid (Polymerization)
None Known
11. Toxicological Information
Miscellaneous Toxicological Information
Over exposure of humans to xylene or xylene solvent mixtures produced predominately central nervous system
(CNS) effects with less common effects reported to the lung, gastrointestinal tract, liver, kidney and heart.
Conditions Aggravated By Exposure
None Known
12. Ecological Information
No Data Available...
13. Disposal Considerations
Dispose in accordance with applicable federal, state and local government regulations. Waste generators must
determine whether a discarded material is classified as a hazardous waste. USEPA guidelines for the classification
determination are listed in 40 CFR Parts 261.3. Additionally, waste generators must consult state and local hazardous
waste regulations to ensure complete and accurate classification.
RCRA Information
Waste solutions may meet the RCRA Ignitable characteristic.
14. Transport Information
Proper Shipping Name
Xylenes
Hazard Class
3, PG. II
DOT Identification Number
UN1307
DOT Shipping Label
Flammable
Packaging Requirements
173.118 & 173.119
15. Regulatory Information
U.S. Regulatory Information
All ingredients of this product are listed or are excluded from listing under the U.S. Toxic Substances Control Act
(TSCA) Chemical Substance Inventory.
Page 4 of 6
MATERIAL SAFETY DATA SHEET
Sikadur Combiflex Kit - Part C
15. Regulatory Information - Continued
SARA Hazard Classes
Acute Health Hazard
Chronic Health Hazard
Fire Hazard
SARA Title III - Section 313 Supplier Notification
This product contains the following toxic chemicals that are subject to the reporting requirements of section 313 of
the Emergency Planning and Community Right-To-Know Act (EPCRA) of 1986 and of 40 CFR 372.
XYLENE (MIXED ISOMERS) (1330-20-7) 90 - 100 %
This information must be included on all MSDSs that are copied and distributed for this material.
SARA Section 313 Notification
This product contains the following toxic chemicals subject to the reporting requirements of Section 313 of the
Emergency Planning and Community Right-To-Know Act of 1986 and of 40 CFR 372. This information must be
included in all MSDSs that are copied and distributed for this material.
Ingredient(s) - U.S. Regulatory Information
XYLENE (MIXED ISOMERS)
SARA Title III - Section 313 Form "R"/TRI Reportable Chemical
SARA - Acute Health Hazard
SARA - Chronic Health Hazard
SARA - Fire Hazard
Ingredient(s) - State Regulations
XYLENE (MIXED ISOMERS)
New Jersey - Workplace Hazard
New Jersey - Environmental Hazard
New Jersey - Special Hazard
Pennsylvania - Workplace Hazard
Pennsylvania - Environmental Hazard
Massachusetts - Hazardous Substance
New York City - Hazardous Substance
16. Other Information
HMIS Rating
Health: *3
F i re : 2
Reactivity: 0
Personal Protection: H
Revision/Preparer Information
MSDS Preparer: EHS Department
MSDS Preparer Phone Number: 201 933 8800
This MSDS Supercedes A Previous MSDS Dated: 11/12/2001
Disclaimer
The data in this Material Safety Data Sheet relates only to the specific material herein and does not relate to use
in combination with any other material or in any process. The information set forth herein is based on technical
data that Sika believes to be reliable as of the date hereof. Since conditions of use are outside our control, we
make no warranties, express or implied and assume no liability in connection with any use of this information.
Nothing herein is to be taken as a license to operate under or a recommendation to infringe any patents.
Page 5 of 6
MATERIAL SAFETY DATA SHEET
Sikadur Combiflex Kit - Part C
Disclaimer - Continued
SIKA CORPORATION
Printed Using MSDS Generator鈩? 2000
Page 6 of 6
|