Search   
MSDS 
:
 Dipentylamine, 99%
CAS 
:
 2050-92-2
SYNONYMS 
:
 Diamylamine; 1-Pentanamine, N-pentyl-; Di-n-amylamine.
**** SECTION 2 - COMPOSITION, INFORMATION ON INGREDIENTS ****

+----------------+--------------------------------------+----------+-----------+
| CAS# | Chemical Name | % | EINECS# |
|----------------|--------------------------------------|----------|-----------|
| 2050-92-2 |Dipentylamine | 99 | 218-108-3 |
+----------------+--------------------------------------+----------+-----------+
Hazard Symbols: T
Risk Phrases: 10 22 24 36/37/38

**** SECTION 3 - HAZARDS IDENTIFICATION ****

EMERGENCY OVERVIEW
Flammable. Harmful if swallowed. Toxic in contact with skin.
Irritating to eyes, respiratory system and skin.

Potential Health Effects
Eye:
Causes eye burns. Vapor or mist may cause irritation and severe
burns. May cause chemical conjunctivitis and corneal damage.
Skin:
Harmful if absorbed through the skin. Causes skin burns. May cause
cyanosis of the extremities. May cause skin rash (in milder cases),
and cold and clammy skin with cyanosis or pale color.
Ingestion:
Harmful if swallowed. May cause severe and permanent damage to the
digestive tract. May cause burns to the gastrointestinal tract.
Ingestion of large amounts may cause CNS depression. May cause
systemic effects.
Inhalation:
Inhalation may be fatal as a result of spasm, inflammation, edema of
the larynx and bronchi, chemical pneumonitis and pulmonary edema. May
cause burns to the respiratory tract. May cause systemic effects. May
cause burning sensation, coughing, wheezing, laryngitis, shortness of
breath, headache, nausea, and vomiting.
Chronic:
Effects may be delayed.

**** SECTION 4 - FIRST AID MEASURES ****

Eyes:
Immediately flush eyes with plenty of water for at least 15 minutes,
occasionally lifting the upper and lower eyelids. Get medical aid
immediately. Do NOT allow victim to rub eyes or keep eyes closed.
Extensive irrigation with water is required (at least 30 minutes).
Skin:
Get medical aid immediately. Immediately flush skin with plenty of
water for at least 15 minutes while removing contaminated clothing
and shoes. Wash clothing before reuse. Destroy contaminated shoes.
Ingestion:
Never give anything by mouth to an unconscious person. Get medical
aid immediately. Do NOT induce vomiting. If conscious and alert,
rinse mouth and drink 2-4 cupfuls of milk or water. Induce vomiting
only when instructed to do so by a physician.
Inhalation:
Get medical aid immediately. Remove from exposure and move to fresh
air immediately. If breathing is difficult, give oxygen. Do not use
mouth-to-mouth resuscitation if victim ingested or inhaled the
substance; induce artificial respiration with the aid of a pocket
mask equipped with a one-way valve or other proper respiratory
medical device.
Notes to Physician:

**** SECTION 5 - FIRE FIGHTING MEASURES ****

General Information:
As in any fire, wear a self-contained breathing apparatus in
pressure-demand, MSHA/NIOSH (approved or equivalent), and full
protective gear. Vapors may form an explosive mixture with air.
Vapors can travel to a source of ignition and flash back. During a
fire, irritating and highly toxic gases may be generated by thermal
decomposition or combustion. Will burn if involved in a fire. Use
water spray to keep fire-exposed containers cool. Containers may
explode in the heat of a fire. Flammable liquid and vapor. Vapors
may be heavier than air. They can spread along the ground and
collect in low or confined areas. Runoff from fire control or
dilution water may cause pollution.
Extinguishing Media:
For small fires, use dry chemical, carbon dioxide, water spray or
alcohol-resistant foam. For large fires, use water spray, fog, or
alcohol-resistant foam. Use water spray to cool fire-exposed
containers. Water may be ineffective. Do NOT use straight streams of
water.

**** SECTION 6 - ACCIDENTAL RELEASE MEASURES ****

General Information: Use proper personal protective equipment as indicated
in Section 8.
Spills/Leaks:
Clean up spills immediately, observing precautions in the Protective
Equipment section. Remove all sources of ignition. Absorb spill using
an absorbent, non-combustible material such as earth, sand, or
vermiculite. Do not use combustible materials such as sawdust. Use a
spark-proof tool. Provide ventilation. A vapor suppressing foam may
be used to reduce vapors.

**** SECTION 7 - HANDLING and STORAGE ****

Handling:
Wash thoroughly after handling. Remove contaminated clothing and
wash before reuse. Use only in a well-ventilated area. Ground and
bond containers when transferring material. Use spark-proof tools and
explosion proof equipment. Do not get in eyes, on skin, or on
clothing. Empty containers retain product residue, (liquid and/or
vapor), and can be dangerous. Keep container tightly closed. Keep
away from heat, sparks and flame. Do not ingest or inhale. Use only
in a chemical fume hood. Discard contaminated shoes. Do not
pressurize, cut, weld, braze, solder, drill, grind, or expose empty
containers to heat, sparks or open flames.
Storage:
Keep away from heat, sparks, and flame. Keep away from sources of
ignition. Store in a cool, dry, well-ventilated area away from
incompatible substances. Flammables-area. Keep containers tightly
closed.

**** SECTION 8 - EXPOSURE CONTROLS, PERSONAL PROTECTION ****

Engineering Controls:
Facilities storing or utilizing this material should be equipped
with an eyewash facility and a safety shower. Use adequate general or
local explosion-proof ventilation to keep airborne levels to
acceptable levels.
Exposure Limits
CAS# 2050-92-2:


Personal Protective Equipment

Eyes:
Wear appropriate protective eyeglasses or chemical
safety goggles as described by OSHA's eye and face
protection regulations in 29 CFR 1910.133 or European
Standard EN166.
Skin:
Wear appropriate protective gloves to prevent skin
exposure.
Clothing:
Wear appropriate protective clothing to prevent skin
exposure.
Respirators:
A respiratory protection program that meets OSHA's 29
CFR 1910.134 and ANSI Z88.2 requirements or European
Standard EN 149 must be followed whenever workplace
conditions warrant respirator use.

**** SECTION 9 - PHYSICAL AND CHEMICAL PROPERTIES ****

Physical State: Clear liquid
Color: clear, colorless
Odor: ammonia-like
pH: Not available.
Vapor Pressure: 0.153 mm Hg @ 25 C
Viscosity: Not available.
Boiling Point: 202.0 - 203.0 deg C @ 760.00m
Freezing/Melting Point: -7.85 deg C
Autoignition Temperature: Not applicable.
Flash Point: 52 deg C ( 125.60 deg F)
Explosion Limits, lower: Not available.
Explosion Limits, upper: Not available.
Decomposition Temperature: Not available.
Solubility in water: slightly soluble
Specific Gravity/Density: .7770g/cm3
Molecular Formula: C10H23N
Molecular Weight: 157.30

**** SECTION 10 - STABILITY AND REACTIVITY ****

Chemical Stability:
Stable under normal temperatures and pressures.
Conditions to Avoid:
Incompatible materials, ignition sources, excess heat.
Incompatibilities with Other Materials:
Strong acids, strong oxidizing agents, acid chlorides, acid
anhydrides, plastics, Absorbs CO2 from the air..
Hazardous Decomposition Products:
Nitrogen oxides, carbon monoxide, carbon dioxide.
Hazardous Polymerization: Has not been reported.

**** SECTION 11 - TOXICOLOGICAL INFORMATION ****

RTECS#:
CAS# 2050-92-2: RZ9100000
LD50/LC50:
CAS# 2050-92-2: Oral, rat: LD50 = 270 mg/kg; Skin, rabbit: LD50 =
350 uL/kg.
Inhalation, rat: LCLo = 63
Carcinogenicity:
Dipentylamine -
Not listed by ACGIH, IARC, or NTP.
Other:
See actual entry in RTECS for complete information.

**** SECTION 12 - ECOLOGICAL INFORMATION ****

Other
No information available.

**** SECTION 13 - DISPOSAL CONSIDERATIONS ****

Dispose of in a manner consistent with federal, state, and local regulations.

**** SECTION 14 - TRANSPORT INFORMATION ****

IATA
Shipping Name: Di-n-AMYLAMINE
Hazard Class: 3 (6.1)
UN Number: 2841
Packing Group: III
IMO
Shipping Name: Di-normal-AMYLAMINE
Hazard Class: 3.3 (6.1)
UN Number: 2841
Packing Group: III
RID/ADR
Shipping Name: Di-n-AMYLAMINE
Hazard Class: 3
UN Number: 2841
Packing group: III

**** SECTION 15 - REGULATORY INFORMATION ****

European/International Regulations
European Labeling in Accordance with EC Directives
Hazard Symbols: T
Risk Phrases:
R 10 Flammable.
R 22 Harmful if swallowed.
R 24 Toxic in contact with skin.
R 36/37/38 Irritating to eyes, respiratory system
and skin.
Safety Phrases:
S 16 Keep away from sources of ignition - No
smoking.
S 24/25 Avoid contact with skin and eyes.
WGK (Water Danger/Protection)
CAS# 2050-92-2: No information available.
Canada
CAS# 2050-92-2 is listed on Canada's DSL List.
CAS# 2050-92-2 is listed on Canada's Ingredient Disclosure List.
US FEDERAL
TSCA
CAS# 2050-92-2 is listed on the TSCA inventory.

**** SECTION 16 - ADDITIONAL INFORMATION ****

MSDS Creation Date: 9/02/1997 Revision #8 Date: 3/28/2005

The information above is believed to be accurate and represents the best
information currently available to us. However, we make no warranty of
merchantability or any other warranty, express or implied, with respect to
such information, and we assume no liability resulting from its use. Users
should make their own investigations to determine the suitability of the
information for their particular purposes. In no way shall the company be
liable for any claims, losses, or damages of any third party or for lost
profits or any special, indirect, incidental, consequential or exemplary
damages, howsoever arising, even if the company has been advised of
the possibility of such damages.
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
Search More   
ALL MSDS PAGES IN THIS GROUP
NAMECAS
Tin(IV) Chloride Anhydrous 7646-78-8
Tin(IV) Chloride Pentahydrate 7646-78-8
2,5-Dimethyl-3-Pyrroline, 75% Remainder 2,5-Dimethyl-1-Pyrroline 59480-92-1
Ruthenium on 1/8-inch alumina pellets (0.5% ru)
6-Fluorotryptamine hydrochloride, 99% 55206-24-1
3-Phenyl-1-propylamine, 98% 2038-57-5
Tin (IV) Oxide 18282-10-5
Isethionic Acid Potassium Salt, 98% (Titr.) 1561-99-5
Tin (II) Chloride Anhydrous 7772-99-8
Tubocurarine Chloride, 98.0 - 102.0% 6989-98-6
Tin (II) Chloride Dihydrate 10025-69-1
Rhodium on srtio3 , 0.5 wt% rh
Cochineal, extract powder
Dimethyl trans-1,2-cyclopropanedicarboxylate, 99+% 826-35-7
3-Aminocrotonamide, Tech. 85% 15846-25-0
Normal-butyl sulfoxide, tech., 93% 2168-93-6
Tin (II) Oxide 21651-19-4
Stearic acid 57-11-4
Starch, Soluble and Hydrolysed 9005-25-8
2-Chloro-3,5-Dinitropyridine, 99% 2578-45-2
Phosphorous acid, 98% 10294-56-1
Poly(Methyl Methacrylate) (Pract) 9011-14-7
Octadecyltrichlorosilane, 95% 112-04-9
Ethyl Propionate, 97+% (gc) 105-37-3
4,4'-Diaminooctafluorobiphenyl, 98% 1038-66-0
Poly(4-methyl-1-pentene), high molecular weight 25068-26-2
Exo-2-Bromo-5-Oxo-Bicyclo(2.2.1)Heptane-Syn-7-Carboxylic Acid, 99% 63377-25-3
3-Methylsulphonylaniline Hydrochloride , 95+% 80213-28-1
Aminoreductone precursor
Propyl Red, 98% (UV-Vis) 2641-01-2
5-Chloro-2-Mercaptobenzothiazole, 98% 5331-91-9
Strontium Chloride Hexahydrate 10025-70-4
3-Hydroxypyridine, 98% 109-00-2
N-Methyl-1,3-propanediamine, 99% 6291-84-5
Perfluoro-compound FC-72 355-42-0
2,4,4-Trimethyl-1-pentene (pract), 95% (gc) 107-39-1
2,6-Dimethoxypyridine, 99% 6231-18-1
Strontium nitrate 10042-76-9
2-Fluoroanisole, 98% 321-28-8
Cholic acid, 99+% (titr.) 81-25-4
1-Amino-1-cyclopentanecarboxylic acid, 97% 52-52-8
Dipentylamine, 99% 2050-92-2
Trioctylpropylammonium bromide, 99% (titr.) 24298-17-7
Styrene monomer, inhibited 100-42-5
p-Nitrocinnamic acid, 97%,predominantly trans 619-89-6
3,4-Dimethoxyphenethyl Alcohol 7417-21-2
Succinic acid 110-15-6
D(+)-Sucrose 57-50-1
2-Chlorothiophene, 98+% 96-43-5
Terephthalic-D4 Acid, 98 Atom % D 60088-54-2

Free MSDS Search ( Providing 250,000+ Material Properties )
Chemcas.com| Ads link:todaystock.net