±±±±±±±±±±±±± 5 STAR MATERIAL SAFETY DATA SHEET ±±±±±±±±±±±±
HEALTH 2
FLAMMABILITY 3
REACTIVITY 0
Products on this MSDS: #5400NR-1 Hi-Solids Acrylic Lacquer Primer Surfacer � Gray (Gallon)
#5400NR-4 Hi-Solids Acrylic Lacquer Primer Surfacer � Gray (Quart)
NOT FOR SALE IN CALIFORNIA
OSHA Hazard Class: Flammable Liquid
DOT Shipping Class: Paint Related Materials UN1263
Hazardous Materials Information: See Section X.
SECTION II. HAZARDOUS INGREDIENTS
Also see Section X.
VAPOR SARA EXPOSURE LIMITS
INGREDIENTS CAS#
PRESSURE 313
OSHA ACGIH STEL CEILING WT %
20°C (MMHg) REPORT
Acrylic Copolymer N/E ---- ---- ---- ---- ---- ---- ----
3 3
Magnesium Silicate 14807-96-6 None No 2.0 mg/m 2.0 mg/m ---- ---- ----
Methyl Isobutyl Ketone 108-10-1 15.00 Yes 100 ppm 50 ppm 75 ppm ---- 1%
2-Proponol 67-63-0 30.00 No 400 ppm 400 ppm 500 ppm ---- ----
15 mg/m3 10 mg/m3
Titanium Dioxide 13463-67-7 N/A No ---- ---- ----
Toluene 108-88-33 36.00 Yes 100 ppm Skin 50 ppm 150 ppm 200 ppm* 40 %
* Denotes 15 Minutes/** Denotes 10 Minutes/ (S) = Supplier/ N/E = Not Established
Note A: Technical grade Xylene contains 18-20% Ethylbenzene (100-41-4), which has 100ppm PEL, 100ppm TLV, 125ppm STEL
and is subject to the reporting requirements of Section 313 of Sara Title III.
See Section X. for specific ingredients and SARA 313 reportable wt.% data.
SECTION III. PHYSICAL DATA
Also see Section X.
Boiling Range: 155°F - 180 °F Evaporation Rate: Slower than Ether
Solubility in H2O: Slight - Miscible Vapor Density: Heavier than Air
Volatile (%) by Volume: 64.00 Volatile (%) by Wt: 45.31
Weight per Gallon: 10.14 lbs./gal. VOC 4.59 lbs./gal.
SECTION IV. FIRE AND EXPLOSION
Flash Point: 52°F
Flammable Limits: .8% - 13%
Extinguishing Media: Water Spray (for containment), Foam, Carbon Dioxide, Dry Chemical.
Special Fire Fighting Procedures:
Full protective equipment, including self-contained breathing apparatus, is recommended. Water from fogging
nozzles may be used to cool closed containers to prevent pressure build up preventing rupturing. Do not use
direct water stream on combustible or flammable liquid fires.
Unusual fire and explosion hazards:
When heated above the defined flash points these solvents emit flammable vapors which, when mixed with air,
can burn or be explosive when exposed to any ignition source. Fine mists or spray may be flammable at
temperatures below the flash point.
SECTION V. HEALTH HAZARD DATA
General Effects:
Ingestion: Gastrointestinal distress. In the unlikely event of ingestion call a physician immediately and have the
names of ingredients available.
Inhalation: May cause nose and throat irritation. Repeated and prolonged overexposure to solvents may lead to
permanent brain and nervous system damage. Eye watering, headaches, nausea, dizziness and loss of
coordination are signs that solvent levels are too high. If affected by inhalation of vapor or spray mist, remove to
fresh air. If breathing difficulty persists, or occurs later, consult a physician.
Skin or Eye Contact: May cause irritation or burning of the eyes. Repeated or prolonged liquid contact may
cause skin irritation with discomfort and dermatitis. In case of eye contact, immediately flush with plenty of
water for at least 15 minutes; call a physician. In case of skin contact, wash with soap and water. If irritation
occurs, contact a physician.
Specific Effects:
Methyl Isobutyl Ketone: Reoccurring overexposure may result in liver and kidney damage.
Magnesium Silicate: Repeated overexposure to talc may lead to chronic lung disease.
Titanium Dioxide: In lifetime inhalation tests, lung cancer was found in some rats exposed to 250-mg/m3
respirable titanium dust. Analysis of the titanium dioxide concentrations in the rat’s lungs showed that the lung
clearance mechanism was overwhelmed and that the results at the massive 250-mg/m3 levels are not relevant to
the workplace.
2-Proponol: Ingestion studies on laboratory animals showed that very high oral doses caused increased liver
and kidney weights.
Toluene: Continuous recurrent overexposure may cause liver or kidney damage. High airborne levels have
produced irregular heartbeats in animals and occasional palpitations in humans. Rats exposed to very high
airborne levels have exhibited high frequency hearing deficits. Warning: This chemical is known to the state of
California to cause birth defects or other reproductive harm.
SECTION VI. REACTIVITY DATA
Stability: Stable
Incompatibility (Materials to avoid): None reasonably foreseeable.
Hazardous Decomposition Products: CO, CO2, Smoke.
Hazardous Polymerization: Will not occur.
SECTION VII. SPILL OR LEAK PROCEDURES
Steps to be taken in case material is released or spilled: Ventilate area. Remove sources of ignition. Prevent skin
contact and breathing of vapor. Wear a properly fitted vapor/particulate respirator (NIOSH/MSHA TC-23C).
Confine and remove with inert absorbent.
Waste Disposal Method: Do not allow material to contaminate ground water systems. Incinerate absorbed material in
accordance with federal, state, and local requirements. Do not incinerate in closed containers.
SECTION VIII. SPECIAL PROTECTION INFORMATION
Do not breathe vapors or mists. Wear a properly fitted vapor/particulate respirator approved by NIOSH/MSHA (TC-23C)
for use with paints during application and until all vapors and spray mists are exhausted. In confined spaces or in
situations where continuous spray operations are typical or proper respirator fit is not possible, wear a positive-pressure,
supplied-air respirator (TC-19C). In all cases, follow the respirator manufacturer’s direction for respirator use. Do not
permit anyone without protection in the painting area.
Ventilation: Provide sufficient ventilation in volume and pattern to keep contaminants below applicable OSHA
requirements.
Protective Clothing: Neoprene gloves and coveralls are recommended.
Eye Protection: Desirable in all industrial situations. Include splashguards or side shields.
SECTION IX. SPECIAL PRECAUTIONS
Precautions to be taken in handling and storing: Observe label precautions. Keep away from heat, sparks and flame.
Close container after each use. Ground containers when pouring. Wash thoroughly after handling and before
eating or smoking. Do not store above 120°F.
Other Precautions: Do not sand, flame cut, braze or weld dry coating without a NIOSH/MSHA approved respirator or
appropriate ventilation.
Warning: KEEP THIS AND ALL PAINT RELATED PRODUCTS OUT OF THE REACH OF CHILDREN!
The information contained in this MSDS is based on data from sources considered to be reliable but ABI®
Autobody Brands International does not guarantee the accuracy or completeness thereof. ABI® urges each
customer or recipient of this MSDS to study it carefully to become aware of and understand the hazards
associated with this product. The reader should consider consulting reference works or individuals who are
experts in ventilation, toxicology or fire prevention as necessary or appropriate to use and understand the data in
this MSDS.
Note: The data on this MSDS relates only to individual components and does not represent the end mixed
product. Read all other Component Material Safety Data Sheets.
±±±±±±±±±±±±±±±±±±±±± END OF MSDS ±±±±±±±±±±±±±±±±±±±±±
|