MATERIAL SAFETY DATA SHEET
MSDS Name: Polyseamseal(R) PRO SILICONIZED ACRYLIC LATEX CAULK -CLEAR
MSDS Number: sD11503
Version Number
MSDS Date: APR-08-1999
Page Number: 1
--------------------------------------------------------------------------------
SECTION I - PRODUCT AND COMPANY INFORMATION
Product Name: Polyseamseal(R) PRO SILICONIZED ACRYLIC
LATEX CAULK -CLEAR Hazard Rating: Health: 1 Fire: 0 Reactivity: 0 PPI: B
Company Identification: OSI SEALANTS, INC.
7405 PRODUCTION DRIVE
MENTOR OH 44060
Contact: Safety Officer
Telephone/Fax: (440) 255-8900 (440) 974-2395
Emergency Phone (24 hour) CHEMTREC
(800) 424-9300
Chemtrec (outside-USA) (703) 527-3887
Preparer T.F.Barr
Sr. R.&D. Chemist
Product Class Acrylic Latex Caulk
Trade Name POLYSEAMSEAL
Product Code -- CLEAR
SECTION II - INGREDIENT AND HAZARD INFORMATION
Ingredient Name CAS Number Percent TSCA
No OSHA hazardous ingredients known at this time.
SECTION III - PHYSICAL AND CHEMICAL PROPERTIES
Form: Milky-white Caulk Appearance/Color: dries CLEAR Odor: none Solubility (in water): yes pH Value, +/-.3: 8.
Boiling Range: 212.炉F (100.炉C) Vapor Pressure (mmHg): 15.@ 68.炉F (20.炉C) Evaporation Rate: 0.5 times Slower than
n-Butyl Acetate
http://www.osisealants.com/MSDS/msds_data/PolySeam_msds/Sd11503.htm (1 of 5) [11/23/2001 9:08:03 PM]
Vapor Density: Heavier than air
% Volatile, Weight 38.%
% Volatile, Volume approx. 40.%
Specific Gravity: 1.055
VOC (less H2O or exempt) 2 g/l
Heavy Elements (ppm) 0.
--------------------------------------------------------------------------------
MATERIAL SAFETY DATA SHEET
MSDS Name: Polyseamseal(R) PRO SILICONIZED ACRYLIC LATEX CAULK -CLEAR
MSDS Number: sD11503
Version Number
MSDS Date: APR-08-1999
Page Number: 2
--------------------------------------------------------------------------------
NOTE:
Odor : Mild acrylic odor. Freeze Point : 32 Deg F
SECTION IV - FIRE FIGHTING MEASURES (Flash,UEL,LEL
for solvent only)
Flammability Class N/A Flash Range: Not Applicable Explosive Range (LEL/UEL): Not Applicable
EXTINGUISHING MEDIA:
Dry chemical -- Carbon Dioxide -- Foam -- Water Fog
Will not burn in wet state.
SPECIAL FIRE-FIGHTING PROCEDURES:
Water may be used to cool and protect exposed containers.
Caution should be taken because uncured material is water soluble.
UNUSUAL FIRE AND EXPLOSION HAZARDS:
Any closed container may burst when exposed to extreme
heat or fire.
SECTION V - HEALTH HAZARD DATA
http://www.osisealants.com/MSDS/msds_data/PolySeam_msds/Sd11503.htm (2 of 5) [11/23/2001 9:08:03 PM]
ROUTES OF ENTRY:
Inhalation? Yes | Skin? Yes | Ingestion? Yes TARGET ORGANS... None- No hazardous ingredients per OSHA
Regulations CARCINOGENICITY... NTP? N/A | IARC Monographs? N/A | OHSA? NO EFFECTS OF
OVEREXPOSURE Inhalation: May irritate respiratory tract. Skin/Eye Contact: May cause irritation. Ingestion:
Swallowing large amounts may cause nausea, vomiting. ( an unlikely route of entry ) FIRST AID MEASURES
Inhalation: If affected by inhalation, remove to fresh air. Eye Contact: Flush with water for at least 15 minutes, and get
prompt medical attention. Skin Contact: Wash skin thoroughly with soap and water. Ingestion: Drink water, and get
medical attention. ------------------------------------------------------------------- N/A= Not applicable N/AV=Not available
N/E, N/est=Not established -------------------------------------------------------------------
SECTION VI - STABILITY AND REACTIVITY
Stability: This product is stable Hazardous Polymerization: Hazardous polymerization will not occur
--------------------------------------------------------------------------------
MATERIAL SAFETY DATA SHEET
MSDS Name: Polyseamseal(R) PRO SILICONIZED ACRYLIC LATEX CAULK -CLEAR
MSDS Number: sD11503
Version Number
MSDS Date: APR-08-1999
Page Number: 3
--------------------------------------------------------------------------------
INCOMPATABILITY:
None
CONDITIONS TO AVOID:
None
HAZARDOUS DECOMPOSITION PRODUCTS:
May produce oxides of carbon and oxides of nitrogen when burned.
SECTION VII - ACCIDENTAL RELEASE AND DISPOSAL
MEASURES:
STEPS TO BE TAKEN IN CASE OF SPILL:
Wear appropriate protective clothing. Add dry absorbent and shovel or sweep up. Place in an appropriate container and
seal.
WASTE DISPOSAL METHOD: Dispose of in accordance with Federal, State, and Local regulations.
http://www.osisealants.com/MSDS/msds_data/PolySeam_msds/Sd11503.htm (3 of 5) [11/23/2001 9:08:03 PM]
SECTION VIII - EXPOSURE CONTROLS/PERSONAL
PROTECTION
Occupational Exposure Limits
ACGIH TLV ACGIH TLV-C ACGIH STEL OSHA STEL OSHA PEL
RESPIRATORY PROTECTION:
NIOSH approved respirators recommended if vapors and mists
are generated.
VENTILATION:
Local exhaust is recommended for safe practice.
PROTECTIVE CLOTHING:
Rubber gloves and impervious clothing should be worn to prevent
repeated skin contact.
EYE PROTECTION:
Splashproof goggles or safety glasses should be worn.
HANDLING AND STORAGE PRECAUTIONS:
Keep from freezing. Keep away from heat.
Keep out of the reach of children
Keep containers closed when not in use
Avoid prolonged or repeated contact with skin.
SECTION IX - TRANSPORT INFORMATION:
DOT CLASSIFICATIONS FOR CARTRIDGES 10 or 29 oz.
DESCRIPTION: Non-hazardous
DOT CLASSIFICATIONS for 1 GALLON or larger CONTAINERS
DESCRIPTION: Non-hazardous Caulking type product
--------------------------------------------------------------------------------
MATERIAL SAFETY DATA SHEET
MSDS Name: Polyseamseal(R) PRO SILICONIZED ACRYLIC LATEX CAULK -CLEAR
MSDS Number: sD11503
Version Number
http://www.osisealants.com/MSDS/msds_data/PolySeam_msds/Sd11503.htm (4 of 5) [11/23/2001 9:08:03 PM]
MSDS Date: APR-08-1999
Page Number: 4
--------------------------------------------------------------------------------
SECTION X - REGULATORY INFORMATION:
SARA Section 313 toxic chemicals: NONE above the de minimis reporting thresholds.
California PROP.65 Chemicals: none known
The components fit the EPA Hazard Category definition of Immediate (Acute) and Delayed (Chronic) Health Hazards
under SARA Sections 311, 312.
All chemical substances are TSCA listed.
DISCLAIMER: The information contained herein is based on data available as of the date of preparation of this
MSDS and which we believe to be reliable. However, no warranty is expressed or implied regarding the accuracy of
the data. We shall not be responsible for the use of this information, or of any product, method, or apparatus men-
tioned, and the user must make his own investigation to determine the suitability of the information or products for his
particular purpose, for the protection of the environment, and the health and safety of the users of this material.
--------------------------------------------------------------------------------
Last Page
http://www.osisealants.com/MSDS/msds_data/PolySeam_msds/Sd11503.htm (5 of 5) [11/23/2001 9:08:03 PM]
|