Acryl-R SM 8500 Acrylic Caulk Page 1
MSDS Number: seal00acr8500 August 18, 2004
________________________________________
MATERIAL SAFETY DATA SHEET
1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATION
______________________
Product Identification
Product Name: Acryl-R SM 8500 Acrylic Caulk
Product Number: pails
Chemical Name: Acrylic Caulk
CAS Number: Blend
Company Identification
______________________
ERSystems - Elastomeric Roofing Systems, Inc
6900 Bleck Dr
Rockford, MN 55373 USA
1-800-403-7747 (For product information)
1-800-535-5053 Infotrac (For emergencies)
2. COMPOSITION/INFORMATION ON INGREDIENTS
COMPONENT LISTING:
Chemical Name
_____________ ________
Amount CAS Number
__________
BUTYL BENZYL PHTHALATE < 5.0 % 85-68-7
(See Section 8 for exposure guidelines)
(See Section 15 for regulatory information)
3. HAZARDS IDENTIFICATION
***************** EMERGENCY OVERVIEW *****************
* *
* CAUTION *
* *
* Prolonged or repeated contact may cause skin or eye *
* irritation. May be harmful if swallowed. Protect *
* from freezing. *
* *
**********************************************************
Acryl-R SM 8500 Acrylic Caulk Page 2
MSDS Number: seal00acr8500 August 18, 2004
____________________________________________________________________________________________________
(section 3 continued)
HMIS Rating - Health: 1
Flammability: 0
Reactivity: 0
Personal Protection Index: G
POTENTIAL HEALTH EFFECTS
EYE:
Direct or prolonged contact may cause reddening or irritation.
SKIN:
Direct or prolonged contact may cause reddening or irritation.
INHALATION:
Trace components and residual vapors may be irritating eyes, skin, mucous
membranes, respiratory tract, and may produce symptoms of headaches, and
nausea in poorly ventilated areas.
INGESTION:
No information regarding ingestion available.
CHRONIC EFFECTS:
This product contains residual amounts of ammonia. Prolonged inhalation
of high concentrations may cause bronchitis and/or pneumonia, with some
residual reduction of pulmonary functions. This product also contains
trace amounts of free formaldehyde. Formaldehyde is identified by OSHA,
NTP, and IARC as a potential carcinogen.
4. FIRST AID MEASURES
EYE CONTACT FIRST AID:
After initial flushing, remove any contact lenses and continue flushing
for at least 15 minutes. Get medical attention if irritation develops or
persists.
SKIN CONTACT FIRST AID:
Remove contaminated clothing and shoes. Wash affected area immediately
with large amounts of soap and water. Get medical attention if irritation
develops or persists.
INHALATION FIRST AID:
If inhaled, remove to fresh air. If not breathing, give artificial
respiration. Get medical attention if cough or other symptoms develop.
Acryl-R SM 8500 Acrylic Caulk Page 3
MSDS Number: seal00acr8500 August 18, 2004
____________________________________________________________________________________________________
(section 4 continued)
INGESTION FIRST AID:
Unless advised otherwise, induce vomiting by giving Ipecac followed by 1-2
glasses of water. Seek medical attention.
5. FIRE FIGHTING MEASURES
FLAMMABLE PROPERTIES
TCC Flash Point: > 93.3 C (> 199.9 F)
Autoignition Temperature: N/A
FLAMMABLE LIMITS IN AIR
LEL: N/A
UEL: N/A
EXTINGUISHING MEDIA:
Non-Flammable (aqueous emulsion). After water evaporates, remaining
material will burn. Use foam for large fires. Use carbon dioxide or dry
chemical for small fires.
FIRE & EXPLOSION HAZARDS:
Irritating or toxic gases and/or aerosols may be produced during burning.
Product will not burn but may spatter if temperature exceeds boiling point
of water.
FIRE FIGHTING INSTRUCTIONS:
As in any fire, wear self-contained breathing apparatus pressure-demand
MSHA/NIOSH (approved or equivalent) and full protective gear.
6. ACCIDENTAL RELEASE MEASURES
SAFEGUARDS (PERSONNEL):
Wear safety goggles. Wear appropriate personal protective equipment.
INITIAL CONTAINMENT:
Contain spilled material. Absorb spills with inert material.
LARGE SPILLS PROCEDURE:
Absorb spill with inert material (e g, dry sand or earth), then place in a
chemical waste container.
Acryl-R SM 8500 Acrylic Caulk Page 4
MSDS Number: seal00acr8500 August 18, 2004
____________________________________________________________________________________________________
7. HANDLING AND STORAGE
RECOMMENDED STORAGE TEMPERATURE
Minimum: 15.6 C (60.1 F)
Maximum: 26.7 C (80.1 F)
SHELF LIFE: (in original, sealed containers)
8 months @ 26.7 C
HANDLING (PERSONNEL):
Avoid prolonged or repeated contact with skin. Wash hands thoroughly
after handling.
HANDLING (PHYSICAL ASPECTS):
Keep from freezing. Keep out of reach of children.
STORAGE PRECAUTIONS:
Do not store near direct heat sources, sparks or flames. Store between
50F and 90F.
8. EXPOSURE CONTROLS / PERSONAL PROTECTION
EYE / FACE PROTECTION REQUIREMENTS:
Wear safety glasses. A respiratory protection program that meets OSHA's
29 CFR 1910-134 and ANSI Z88-2 requirements must be followed whenever
workplace conditions warrant a respirator's use.
SKIN PROTECTION REQUIREMENTS:
Selection of specific items such as gloves, boots, apron or full-body suit
will depend on operation. Wash hands thoroughly after handling.
RESPIRATORY PROTECTION REQUIREMENTS:
Respiratory protection is not usually required under normal uses. When
established airborne exposure limits for ammonia or formaldehyde are
surpassed, wear OSHA/NIOSH approved respirator.
EXPOSURE GUIDELINES:
No Information Available.
Acryl-R SM 8500 Acrylic Caulk Page 5
MSDS Number: seal00acr8500 August 18, 2004
____________________________________________________________________________________________________
9. PHYSICAL AND CHEMICAL PROPERTIES
FORM ...............: Semi-solid
ODOR ...............: Faint Odor
BOILING POINT ......: 212 F
VAPOR DENSITY ......: <1 (Air = 1)
SPECIFIC GRAVITY ...: 1.27 (Water = 1)
PH .................: 8.5 to 9.0
10. STABILITY AND REACTIVITY
STABILITY:
Stable.
POLYMERIZATION:
Product will not undergo polymerization.
INCOMPATIBILITY WITH OTHER MATERIALS:
Avoid contact with acids and oxidizing agents.
DECOMPOSITION:
During a fire this material may form carbon monoxide.
11. TOXICOLOGICAL INFORMATION
No information available.
12. ECOLOGICAL INFORMATION
No information available.
13. DISPOSAL CONSIDERATIONS
WASTE DISPOSAL:
Treat or dispose of waste material in accordance with all local,
state/provincial, and national requirements.
Acryl-R SM 8500 Acrylic Caulk Page 6
MSDS Number: seal00acr8500 August 18, 2004
____________________________________________________________________________________________________
14. TRANSPORTATION INFORMATION
PRODUCT LABEL ..........: Acryl-R SM 8500 Acrylic Caulk
D.O.T. SHIPPING NAME ...: N/A
D.O.T. HAZARD CLASS ....: Non-Hazardous
15. REGULATORY INFORMATION
Canadian Disclosure List
BUTYL BENZYL PHTHALATE (85-68-7)
CERCLA Hazardous Substances
BUTYL BENZYL PHTHALATE (85-68-7) -- RQ 100 lb
RCRA Hazardous Substances
BUTYL BENZYL PHTHALATE (85-68-7) -- RCRA Code: Unknown
Title V
BUTYL BENZYL PHTHALATE (85-68-7)
16. OTHER INFORMATION
PREPARED BY .......: Laura
APPROVED BY .......: Laura Vollenweider
TITLE .............: Chemist
APPROVAL DATE .....: September 24, 2003
SUPERCEDES DATE ...: New
MSDS NUMBER .......: seal00acr8500
RTN NUMBER ........: 00000045 (Official Copy)
ADDITIONAL INFORMATION:
The data in this Material Safety Data Sheet relates only to the specific
material designated herein.
**********************************************************************
To the best of our knowledge, the information contained in this MSDS is
accurate. It is intended to assist the user in his evaluation of the
product's hazards, and safety precautions to be taken in its use. The
data in this MSDS relate only to the specific material designated herein.
We do not assume liability for the use of, or reliance on this
information, nor do we guarantee its accuracy or completeness.
**********************************************************************
END OF MSDS
**********************************************************************
|