Material Safety
Data Sheet
95 Goodwin Street, East Hartford, CT., 06108 (860) 528-9838 Date Prepared 8/1/2006
HAZARD RATING 3
Health
SECTION I - IDENTIFICATION 0 = Least 1
Flammability
1 = Slight
Dur-A-Glaze #4 Regular Hardener 0
2 = Moderate
IDENTITY (As Used on Label) Reactivity
3 = High
G
4 = Extreme
Cycloaliphatic Diamine Epoxy Hardener
COMMON NAME Personal Protection
SECTION II - PRODUCT COMPONENTS CAS.# OSHA PEL ACGIH TLV
1
Benzyl Alcohol 100-51-6 N.E. N.E.
3, Aminomethyl -3,5,5-Trimethyl 2855-13-2 N.E. N.E.
1, 5 Pentanediamine, 2 Methyl 15520-10-2 N.E. N.E.
N, Aminoethyl Piperazine 140-31-8 N.E. N.E.
Diglycidyl Ether Bisphenol A Epoxy Resin 25085-99-8 N.E. N.E.
Salicylic Acid 69-72-7 N.E. N.E.
1
None Established
T.S.C.A. Status - O.K. on all above components.
*FOR SPILL, LEAK, FIRE, OR ACCIDENT, CALL CHEMTREC 24-HOUR EMERGENCY NUMBER 1-800-424-9300*
SECTION III - PHYSICAL/CHEMICAL CHARACTERISTICS
Boiling Point Specific Gravity (H2O = 1)
485F <1
Vapor Pressure (mm Hg) Melting Point
0.02 N/A
Vapor Density (AIR = 1) Evaporation rate (Butyl Acetate = 1)
N/A N/A
Solubility in Water Partially soluble.
Appearance and Odor Pale yellow colored liquid. Amine odor.
SECTION IV - FIRE and EXPLOSION HAZARD DATA
Flash Point (Closed Cup Method) Flammable Limits LEL UEL
220F N/A N/A
Extinguishing Media Dry chemicals, carbon dioxide, foam, water spray.
Special Firefighting Procedures
Firefighters should wear full emergency equipment with self-contained breathing apparatus. Irritating gases may be generated
by fire.
Unusual Fire and Explosion Hazards
Cool exposed containers with cold water spray to prevent pressure buildup that may rupture the containers.
SECTION V - REACTIVITY DATA
Conditions to Avoid
Stability Unstable
Stable X Keep container closed when not in use.
Incompatibility (Materials to Avoid) Strong oxidizers and acids.
Hazardous Decomposition or Byproducts By Fire- carbon monoxide, carbon dioxide, aldehydes, nitrogen.
Conditions to Avoid
May Occur Uncontrolled reaction with epoxy resins. Avoid breathing fumes
Hazardous
Polymerization Will Not Occur
X generated by hardener and epoxy mixture when not used within established pot life.
SECTION VI - HEALTH HAZARD DATA
Route(s) of Entry: Inhalation? Skin? Ingestion?
YES YES YES
Irritation on skin.
Signs and Symptoms of Exposure
Health Hazards (Acute and Chronic)
Note: Persons with lung disorders or who are sensitized should not use this product.
ACUTE - Irritation on skin and dermatitis.
CHRONIC - Repeated overexposure will cause severe skin irritation, dermatitis and sensitization.
Sensitized persons may experience rapid irritation of skin upon exposure.
Carcinogenicity: NTP? IARC Monographs? OSHA Regulated?
NO NO NO
Medical Conditions Generally Aggravated by Exposure
Allergy, skin disorders.
Emergency and First Aid Procedures
EYES - Flush with water, holding lids open for 15 minutes or more. Call physician for advice if necessary.
SKIN - PROMPTLY wash with soap and water. DO NOT wash with solvents. Seek medical advice if
irritation develops or persists.
INHALATION - Move person to fresh air if effects occur. If needed, give oxygen or artificial respiration
to improve breathing . Consult physician.
INGESTION - Get medical attention immediately. Never give liquids to an unconscious or convulsing person.
SECTION VII - CONTROL MEASURES
Respiratory Protection (Specify Type)
Provide adequate exhaust ventilation; use a NIOSH approved respirator if PELs/TLVs are exceeded.
Ventilation Local Exhaust Special
If needed. None known.
Mechanical Adequate exhaust ventilation must exhaust AWAY from applicator.
Protective Gloves Eye Protection
Natural or Neoprene gloves. Splash goggles or face shield.
Other Protective Clothing or Equipment
Use rubber apron, face shield and appropriate clothing to prevent contact with skin. Launder contaminated
clothing before reuse. Discard contaminated leather shoes and canvas sneakers. Protective skin creams
help cleaning with soap and water, gloves must be still be worn. An eye wash station or an adequate supply
of clean water must be available at work area.
Work/Hygienic Practices Enforce careful handling to prevent splashing. Wash thoroughly after use.
SECTION VIII - PRECAUTIONS FOR SAFE HANDLING AND USE
Steps to be Taken in Case Material is Released or Spilled
Wear protective equipment to prevent exposure. Stop spill and dike to prevent spreading. Cover spill with
absorbent materials and collect into containers. Clean contaminated area with detergent and water or a
steam cleaner for best results.
Waste Disposal Method
Dispose in accordance with Federal, State, and Local requirements.
Precautions to be Taken in Handling and Storing
Keep containers tightly closed when not in use.
Other Precautions NONE KNOWN.
Michael P. Michalewich R&D Chemist
Prepared by
"The above information is accurate to the best of our knowledge. However, since data, safety standards, and government regulations are subject to
PLEASE change and the conditions of handling and use, or misuse, are beyond our control, Dur-A-Flex, Inc. MAKES NO WARRANTY, EITHER EXPRES
NOTE OR IMPLIED, WITH RESPECT TO THE COMPLETENESS OR CONTINUING ACCURACY OF THE INFORMATION CONTAINED HEREIN AND
DISCLAIMS ALL LIABILITY FOR RELIANCE THEREON. User should satisfy himself that he has all current data relevant to his particula
use."
Material Safety
Data Sheet
95 Goodwin Street, East Hartford, CT., 06108 (860) 528-9838 Date Prepared 8/1/2006
HAZARD RATING 1
Health
SECTION I - IDENTIFICATION 0 = Least 1
Flammability
1 = Slight
Shop Floor Resin, all colors 0
2 = Moderate
IDENTITY (As Used on Label) Reactivity
3 = High
G
4 = Extreme
Pigmented Epoxy Resin
COMMON NAME Personal Protection
SECTION II - PRODUCT COMPONENTS CAS.# OSHA PEL ACGIH TLV
1
Diglycidyl Ether Bisphenol A Epoxy Resin 25068-38-6 N.E. N.E.
Aliphatic Glycidyl Ether Diluent 68609-97-2 N.E. N.E.
15mg/m3 10mg/m3
Titanium Dioxide 13463-67-7
3
10mg/m3
Calcium Carbonate 1317-65-3 15mg/m
15mg/m3 2mg/m3
Aluminum Silicate 1332-58-7
2 3
10mg/m3
Barium Sulfate 7727-43-7 10mg/m
3
10mg/m3
Inorganic Iron Oxides 1309-37-1 15mg/m
Chromium(III) Oxide Green(trivalent chromium)*3 1.0mg/m3 0.5mg/m3
1308-38-9
1
Not Established
2
Barium Sulfate is listed in SARA III, Part 372, Section 313.
*3
This product contains only 1-3ppm (0.0001%-0.0003%) leachable hexavalent chromium. Trivalent chromium is not
specifically listed as a possible carcinogen. Only in Dark Green and Light Green pigmented systems.
T.S.C.A. Status - O.K. on all above components.
*FOR SPILL, LEAK, FIRE, OR ACCIDENT, CALL CHEMTREC 24-HOUR EMERGENCY NUMBER 1-800-424-9300*
SECTION III - PHYSICAL/CHEMICAL CHARACTERISTICS
Boiling Point Specific Gravity (H2O = 1)
N/A 1.2
Vapor Pressure (mm Hg) Melting Point
N/A N/A
Vapor Density (AIR = 1) Evaporation rate (Butyl Acetate = 1)
N/A >1
Solubility in Water Not Soluble
Appearance and Odor Pigmented viscous liquid. Mild characteristic odor.
SECTION IV - FIRE and EXPLOSION HAZARD DATA
Flash Point (Closed Cup Method) Flammable Limits LEL UEL
485潞F N/A N/A
Extinguishing Media Water spray, Foam, CO2, Dry Chemicals.
Special Firefighting Procedures
Wear full protective equipment including self - contained breathing apparatus.
Unusual Fire and Explosion Hazards
Cool storage containers with water spray to prevent pressure build-up that may rupture the containers.
Combustion products may be toxic.
SECTION V - REACTIVITY DATA
Conditions to Avoid
Stability Unstable
Stable X Excess heating over long periods of time degrades the resin.
Incompatibility (Materials to Avoid) Uncontrolled reaction with amines.
Hazardous Decomposition or Byproducts By Fire - Carbon monoxide, Carbon dioxide, Nitrogen oxides, Aldehydes.
Conditions to Avoid
May Occur
Hazardous
Polymerization Will Not Occur
X Uncontrolled reaction with amines.
SECTION VI - HEALTH HAZARD DATA
Route(s) of Entry: Inhalation? Skin? Ingestion?
YES YES YES
Irritation of skin.
Signs and Symptoms of Exposure
Health Hazards (Acute and Chronic)
ACUTE - Irritation of skin and dermatitis.
CHRONIC - Repeated overexposure will cause severe skin irritation, dermatitis and sensitization. Sensitized
persons may experience rapid irritation of skin upon exposure.
Persons with lung disorders or who are sensitized should not use this product.
Carcinogenicity: NTP? IARC Monographs? OSHA Regulated?
NO NO NO
Medical Conditions Generally Aggravated by Exposure
Allergy, skin disorders.
Emergency and First Aid Procedures
EYES - Flush with water, holding lids open for 15 minutes or more. Call physician for advice if necessary.
SKIN - PROMPTLY wash with soap and water. DO NOT wash with solvents. Seek medical advice if
irritation develops or persists.
INHALATION - Move person to fresh air if effects occur. If needed, give oxygen or artificial respiration
to improve breathing . Consult physician.
INGESTION - Get medical attention immediately. Never give liquids to an unconscious or convulsing person.
SECTION VII - CONTROL MEASURES
Respiratory Protection (Specify Type)
Provide adequate exhaust ventilation; use a NIOSH - approved respirator if PELS/TLVS are exceeded.
Ventilation Local Exhaust Special
If needed. None known.
Mechanical Adequate exhaust ventilation must exhaust AWAY from applicator.
Protective Gloves Eye Protection
Natural rubber or Neoprene. Splash goggles or face shield.
Other Protective Clothing or Equipment
Use rubber apron, face shield and appropriate clothing to prevent contact with skin. Launder contaminated
clothing before reuse. Discard contaminated leather shoes and canvas sneakers. Protective skin creams help
cleaning with soap and water, gloves must still be worn. An eye wash station or an adequate supply of clean
water must be available at work area.
Work/Hygienic Practices Enforce careful handling to prevent splashing. Wash thoroughly after use.
SECTION VIII - PRECAUTIONS FOR SAFE HANDLING AND USE
Steps to be Taken in Case Material is Released or Spilled
Wear protective equipment to prevent exposure. Stop spill and dike to prevent spreading. Cover spill with
absorbent materials and collect into containers. Clean contaminated area with detergent and water or a steam
cleaner for best results.
Waste Disposal Method
Dispose in accordance with Federal, State and Local requirements.
Precautions to be Taken in Handling and Storing
Keep containers tightly closed when not in use.
Other Precautions NONE KNOWN.
Prepared by Samet Dy - Urethane Chemist
"The above information is accurate to the best of our knowledge. However, since data, safety standards, and government regulations are subject to
PLEASE change and the conditions of handling and use, or misuse, are beyond our control, Dur-A-Flex, Inc. MAKES NO WARRANTY, EITHER EXPRES
NOTE OR IMPLIED, WITH RESPECT TO THE COMPLETENESS OR CONTINUING ACCURACY OF THE INFORMATION CONTAINED HEREIN AND
DISCLAIMS ALL LIABILITY FOR RELIANCE THEREON. User should satisfy himself that he has all current data relevant to his particula
use."
Material Safety
Data Sheet
95 Goodwin Street, East Hartford, CT., 06108 (860) 528-9838 Date Prepared 8/1/2006
HAZARD RATING 3
Health
SECTION I - IDENTIFICATION 0 = Least 0
Flammability
1 = Slight
2 0
Flintshot, 1/2, 00, 0,F70, 290 Flour, Special Bond Sands
IDENTITY (As Used on Label) 2 = Moderate Reactivity
3 = High
F
4 = Extreme
Sand Aggregate
COMMON NAME Personal Protection
SECTION II - PRODUCT COMPONENTS CAS.# % OSHA PEL ACGIH TLV
1 3
0.05 mg/m3
Crystalline Silica (Quartz) 14808-60-7 70-90 10mg/m
%Si02+2
1
Crystalline silica can be a lung injury and cancer hazard. Do not breathe dust. May cause delayed lung injury. Long term
exposure can cause silicosis, a respiratory disease which can result in a delayed, disabling, and sometimes fatal lung injury.
Crystalline silica inhaled from occupational sources can from occupational sources can cause cancer in humans. Risk of
injury is dependent on the duration and level of exposure.
2
Includes .45-.55 Sand, F-62, F-70 Grades, NJ 1/4, NJ 000, NJ 1/2, Q-Rok #2 and #3
T.S.C.A. Status - O.K.
*FOR SPILL, LEAK, FIRE, OR ACCIDENT, CALL CHEMTREC 24-HOUR EMERGENCY NUMBER 1-800-424-9300*
SECTION III - PHYSICAL/CHEMICAL CHARACTERISTICS
Boiling Point Specific Gravity (H2O = 1)
4046潞F 2.65
Vapor Pressure (mm Hg) Melting Point
N/A 2930潞F
Vapor Density (AIR = 1) Evaporation rate (Butyl Acetate = 1)
N/A N/A
Solubility in Water INSOLUBLE
Appearance and Odor Naturally rounded sand. Various sizes. No odor.
SECTION IV - FIRE and EXPLOSION HAZARD DATA
Flash Point (Closed Cup Method) Flammable Limits LEL UEL
N/A N/A N/A
Extinguishing Media Compatible with all extinguishing media. Use any media appropriate for the surrounding fire.
Special Firefighting Procedures
N/A
Unusual Fire and Explosion Hazards
N/A
SECTION V - REACTIVITY DATA
Conditions to Avoid
Stability Unstable
Stable X NONE KNOWN.
Incompatibility (Materials to Avoid) Hydrofluoric Acid and powerful oxidizing agents.
Hazardous Decomposition or Byproducts NONE KNOWN.
Conditions to Avoid
May Occur
Hazardous
Polymerization Will Not Occur
X NONE KNOWN.
SECTION VI - HEALTH HAZARD DATA
Route(s) of Entry: Inhalation? Skin? Ingestion?
Yes NO NO
Shortness of breath and reduced pulmonary function.
Signs and Symptoms of Exposure
Health Hazards (Acute and Chronic)
ACUTE - NO SYMPTOMS.
CHRONIC - excessive inhalation of dust may result in respiratory disease such as silicosis, pulmonary fibrosis,
etc. The IARC has evaluated in Vol.42 (monographs) that there is "sufficient evidence for the Carcinogenicity
of crystalline silica dust to experimental animal" and "limited evidence" with respect to humans.
Carcinogenicity: NTP? IARC Monographs? OSHA Regulated?
Yes (Respirable Silica) YES*Level 2A Grouping NO
Medical Conditions Generally Aggravated by Exposure
Lung disorders and persons subject to eye irritation.
Emergency and First Aid Procedures
EYES - Flush with water, holding lids open for 15 minutes or more. Call physician for advice if necessary.
SKIN - PROMPTLY wash with soap and water. DO NOT wash with solvents. Seek medical advice if
irritation develops or persists.
INHALATION - Move person to fresh area if effects occur. If needed, give oxygen or artificial respiration
to improve breathing . Consult physician.
INGESTION - Expected to be slightly toxic by ingestion. If swallowed, induce vomiting immediately as directed by a physcian.
Get medical attention immediately. Never give liquids to an unconscious or convulsing person.
OTHER HEALTH EFFECTS - Medical conditions which may be aggravated by exposure to this product include, conjunctivitis
of the eye, dermatitis of the skin, asthma and respiratory diseases.Sensitization may occur by skin contact.
**NOTE** persons with lung disorders or who are sensitized should not use this product.
SECTION VII - CONTROL MEASURES
Respiratory Protection (Specify Type): Atmospheric
levels should be maintained below the exposure limits listed in section II by
using engineering controls. Provide adequate exhaust ventilation and/or NIOSH approved cartridge respirator.
Ventilation Local Exhaust To meet PEL requirements. Special None Known.
Mechanical Adequate to meet PEL requirements.
Protective Gloves Eye Protection
Recommended. Recommended
Other Protective Clothing or Equipment
Use adequate ventilation and dust collection. To minimize exposure, wear a respirator approved for silica dust when using,
handling, storing or disposing of this product. Refer to the most recent standards of ANSI (Z88.2), OSHA (29 CFR 1910.134),
MHSA (30 CFR Parts 56 and 57), and NIOSH Respirator Decision Logic. Maintain, clean and fit test respirators in accordance
with OSHA regulations.
Work/Hygienic Practices Avoid creating and breathing dust.
SECTION VIII - PRECAUTIONS FOR SAFE HANDLING AND USE
Steps to be Taken in Case Material is Released or Spilled
Do not breathe dust. Do not rely on your sight to determine if dust is in the air. Silica may be in the air without a visible dust
cloud. Avoid creation of respirable dust
Waste Disposal Method
Dispose waste material in a sanitary land fill or as regulated by local, state and federal regulations.
Precautions to be Taken in Handling and Storing
Avoid creation of respirable dust. Take precaution against bag breakage.
Other Precautions None Known.
Prepared by Samet Dy - Urethane Chemist
"The above information is accurate to the best of our knowledge. However, since data, safety standards, and government regulations are subject to
PLEASE change and the conditions of handling and use, or misuse, are beyond our control, Dur-A-Flex, Inc. MAKES NO WARRANTY, EITHER EXPRES
NOTE OR IMPLIED, WITH RESPECT TO THE COMPLETENESS OR CONTINUING ACCURACY OF THE INFORMATION CONTAINED HEREIN AND
DISCLAIMS ALL LIABILITY FOR RELIANCE THEREON. User should satisfy himself that he has all current data relevant to his particula
use."
|