MATERIAL SAFETY DATA SHEET
SECTION 1: PRODUCT AND COMPANY IDENTIFICATION
PRODUCT NAME: POWERCRETE J Part B
PRODUCT SYNONYMS
PRODUCT USE: Part B of a 2-Part Epoxy Coating System
PRODUCT/MSDS DISTRIBUTION: United States
MANUFACTURER: Covalence Specialty Materials
DIVISION: Corrosion Protection Group
ADDRESS: 11010 Wallisville Road,
Houston, TX, 77013
EMERGENCY TELEPHONE NUMBER: CHEMTREC 1-800-424-9300
OTHER TECHNICAL/HEALTH/SAFETY INFORMATION: (713) 676-0085
This product is a resinous suspension that provides the hardening properties to a 2-part
CHEMICAL FAMILY:
epoxy adhesive.
Part B is a finished product that provides the hardening component in a resinous
PRODUCT USE:
suspension with an as-designed, intended-use consisting of direct end-use application in a
2-part liquid epoxy coating system in combination with the proper Part A component.
When combined with the proper Part A component, the resulting liquid epoxy coating has
an end-use application in metal and plastic bonding where corrosion protection is desired
(see, Tyco Adhesives Product Installation and Use Instructions that accompany the
product).
This product is not considered an Article thus may be regulated under US-OSHA; CAN-WHMIS; IOSH; ISO; UK-CHIP; or EU
Directives (67/548/EEC-Dangerous Substance Labeling, 98/24/EC-Chemical Agents at Work, 99/45/EC-Preparation Labeling,
2001/58/EC-MSDS Content), and an MSDS is required for this product considering that when used as recommended or
intended, or under ordinary conditions, it may present a health and safety exposure or other hazard.
Additional Information
No additional information. When combined with the proper Part A component, this product is intended for harsh environments,
such as wet bonding applications. Please request information if considering non-STP, incompatible-conditions or use beyond
current product labeling or instructions. Note that Part B should not be stored/dispensed in high temperature or humid/wet
conditions without precaution.
SECTION 2: COMPOSITION/INFORMATION ON INGREDIENTS
INGREDIENT CAS No. % by Wt
Trimethylhexamethylenediamine 25620-58-0 30 - 60
Modified amine Proprietary 15 - 40
Paratertiarybutylphenol 98-54-4 15 - 40
Diethylenetriamine 111-40-0 5 - 10
Benzyl alcohol 100-51-6 3-7
Hydrophobic silica 67762-90-7 1-5
Additional Information No additional information
SECTION 3: HAZARDS IDENTIFICATION
EMERGENCY OVERVIEW:
Warning! Corrosive to skin and eyes. Harmful if absorbed through skin. May cause dermatitis and sensitization and have
effects on central nervous system, liver, and kidneys. Avoid contact with skin, eyes, and clothing. Avoid breathing vapor,
mist, or spray. Store in tightly closed containers in dry area. Use only with adequate ventilation. Wash thoroughly after
handling.
Powercrete J Part B Revision 5 Revision Date: July 3, 2006 PAGE 1 OF 7
POTENTIAL HEALTH EFFECTS
EYES: This material is corrosive and can cause severe burns to the eyes. Direct contact or exposure to vapors
or mists may cause stinging, tearing, redness, corneal damage and irreversible eye damage. Persons
with pre-existing eye disorders may be more susceptible to the effects of this material.
This material is corrosive and can cause severe burns to the skin. Direct contact can be severely irritating
SKIN:
to the skin and may result in redness, swelling, burns and severe skin damage. Skin contact may be
harmful. Toxic when absorbed though the skin. Persons with pre-existing skin disorders may be more
susceptible to the effects of this material.
May be harmful or fatal if swallowed. Ingestion my cause severe irritation and burns of the mouth, throat
INGESTION:
and digestive tract.
Breathing vapors or mists may cause severe irritation and burns of the nose, throat and respiratory tract.
INHALATION:
Symptoms of overexposure may include coughing, tightness of the chest or shortness of breath.
Repeated exposure may cause an allergic respiratory reaction in sensitized individuals. Pre-existing lung
disorders (for example asthma-like conditions) may be aggravated by exposure to vapors or mists.
ACUTE HEALTH HAZARDS:
Corrosive, may cause burns to eyes, skin, and respiratory tract.
CHRONIC HEALTH HAZARDS:
Repeated or prolonged overexposure may cause sensitization. Harmful if absorbed through skin. May have effects on the
central nervous system, liver,and kidneys.
MEDICAL CONDITIONS GENERALLY AGGRAVATED BY EXPOSURE:
Pre-existing eye, skin, and respiratory disorders may be aggravated by exposure.
Additional Information
Under certain conditions of use, such as sanding the cured product, dusts may be formed. Contact with dusts may be
abrasive and irritating to the eyes, skin and respiratory tract. Prolonged or repeated overexposure to dusts may result in
chronic bronchitis (lung inflammation) with symptoms of coughing and shortness of breath. Persons with pre-existing eye and
skin disorders may be more susceptible to the effects of dust exposure. Respiratory symptoms associated with pre-existing
lung disorders (e.g., asthma conditions) may be aggrevated by exposure to dust.
SECTION 4: FIRST AID MEASURES
Holding eyelids apart, flush affected eye(s) with clean water for at least 20 minutes. Seek immediate
EYES:
medical attention.
Under a safety shower, immediately remove contaminated clothing and shoes. Wash affected area(s) with
SKIN:
plenty of mild soap and water. Seek immediate medical attention. Discard or decontaminate clothing
before reuse and destroy contaminated shoes.
DO NOT induce vomiting. If victim is conscious and alert, immediately rinse mouth with water and dilute
INGESTION:
the ingested material by giving 3-4 glasses of water to drink. Do not give anything by mouth to an
unconscious or convulsing person. Seek immediate medical attention.
If respiratory or other symptoms of exposure develop, move victim to fresh air and seek medical attention.
INHALATION:
If breathing difficulties develop, oxygen should be administered by qualified personnel. Seek immediate
medical attention. If victim is not breathing, move to fresh air and immediately begin artificial respiration.
Keep victim warm and quiet; seek immediate medical attention.
Additional Information
Promptly remove wet contaminated non-impervious clothing, wash before reuse. Destroy contaminated leather and absorbant
shoes.
SECTION 5: FIRE-FIGHTING MEASURES
> 93.3掳 C (>200 掳 F) CC
Flash Point
No data available
Autoignition temperature
No data available
Lower Explosive Limit (LEL)
Powercrete J Part B Revision 5 Revision Date: July 3, 2006 PAGE 2 OF 7
No data available
Upper Explosive Limit (UEL)
Extinguishing Media
Water, foam, dry chemical, carbon dioxide.
Special Fire Fighting Procedures
Fireman should wear self-contained breathing apparatus.
Unusual Fire and Explosion Hazards
Decomposition and combustion products may be toxic.
HMIS HAZARD CLASSIFICATION
HEALTH: 3 FLAMMABILITY: 1 REACTIVITY: 0
Additional Information : No additional information.
SECTION 6: ACCIDENTAL RELEASE MEASURES
ACCIDENTAL RELEASE MEASURES:
Avoid all personal contact. Absorb with sand or other absorbent material. Shovel into closable containers for disposal. Wear
appropriate personal protective equipment. Flush contaminated area with water. Avoid discharge to sewer.
Additional Information
No additional information
SECTION 7: HANDLING AND STORAGE
HANDLING AND STORAGE:
Mixing and application should be done in a well-ventilated area. Local exhaust is recommended; general dilution ventilation is
acceptable. Avoid all personal contact. Keep containers tightly closed. Wash thoroughly after using. Parts A and B release
heat when combined. Store in a cool, well-ventilated area.
OTHER PRECAUTIONS:
Store away from direct sunlight under normal storage conditions of approximately 23C and 50% Relative Humidity to maximize
the shelf life of this product and to avoid product degradation prior to use as-intended. Storage at temperatures beyond
normal-use conditions may adversely affect product functionality, and elevated temperatures may create hazardous conditions.
Additional Information
Containers, even those that have been emptied, can contain hazardous residues. Protect containers from physical damage to
avoid leaks and spills.
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION
ENGINEERING CONTROLS:
Use with adequate ventilation.
VENTILATION:
Local exhaust is recommended; general dilution ventilation is acceptable.
RESPIRATORY PROTECTION:
If ventilation is inadequate, use NIOSH approved respirator for organic vapor.
EYE PROTECTION:
Wear chemical goggles.
SKIN PROTECTION:
Wear chemical resistant gloves as a standard procedure to prevent skin contact.
OTHER PROTECTIVE CLOTHING OR EQUIPMENT:
None
EXPOSURE GUIDELINES:
Powercrete J Part B Revision 5 Revision Date: July 3, 2006 PAGE 3 OF 7
Trimethylhexamethylenediamine
OSHA Permissible Exposure Limit (PEL) Not Established
ACGIH Threshold Limit Value (TLV) Not Established
Modified amine
OSHA Permissible Exposure Limit (PEL) Not Established
ACGIH Threshold Limit Value (TLV) Not Established
Paratertiarybutylphenol
OSHA Permissible Exposure Limit (PEL) Not Established
ACGIH Threshold Limit Value (TLV) Not Established
Diethylenetriamine
OSHA Permissible Exposure Limit (PEL) Not Established
ACGIH Threshold Limit Value (TLV) 1 ppm (skin)
Benzyl alcohol
OSHA Permissible Exposure Limit (PEL) Not Established
ACGIH Threshold Limit Value (TLV) Not Established
Hydrophobic silica
15 mg/m3 (T)
OSHA Permissible Exposure Limit (PEL)
5 mg/m3 (R)
10 mg/m3 (I)
ACGIH Threshold Limit Value (TLV)
3 mg/m3 (R)
(R)
Respirable fraction
(I)
Inhalable particles
(T)
Total dust
(Skin) Danger of cutaneous absorption
Additional Information No additional information
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
Light Brown
APPEARANCE:
Amine odor
ODOR:
Viscous resinous suspension
PHYSICAL STATE:
11
pH:
>200掳 C (392掳 F)
BOILING POINT:
Not available
FREEZING POINT:
< 22.68 mmHg at 21掳 C
VAPOR PRESSURE:
Not available
VAPOR DENSITY (AIR = 1):
1. +/- 0.02 at 25掳 C (77掳 F)
SPECIFIC GRAVITY (H2O = 1):
Not available
EVAPORATION RATE:
Slightly miscible
SOLUBILITY IN WATER:
Not available
% VOLATILE BY VOLUME
Not available
WATER/OIL PARTITION COEFFICIENT
Not available
VISCOSITY (poise @ 25掳 C
Additional Information
No additional information
SECTION 10: STABILITY AND REACTIVITY
This product is stable under normal conditions at ambient temperature.
STABILITY:
Strong oxidizers and acids.
INCOMPATIBILITY (MATERIAL TO AVOID):
Hazardous thermal degradation and combustion products include carbon
HAZARDOUS DECOMPOSITION OR BY-
monoxide, carbon dioxide, aldehydes, and nitrogen oxides. Nitrogen
PRODUCTS:
oxide can react with water vapor to form corrosive nitric acid. Heating
may release ammonia, nitrosamines, and other irritating and toxic
Powercrete J Part B Revision 5 Revision Date: July 3, 2006 PAGE 4 OF 7
compounds.
Will not occur.
HAZARDOUS POLYMERIZATION:
Additional Information
Thermal degradation is not significant at temperatures achieved during proper application, as directed by product instructions.
SECTION 11: TOXICOLOGICAL INFORMATION
Toxicity Values
Oral LD50: (RAT) >500 mg/kg (estimate); Dermal LD50: (Rabbit) >1000 mg/kg (estimate).
Irritancy of Product
Corrosive. Causes eye and skin burns.
Sensitization of Product
Potential sensitizer. No sensitazation observed in Guinea pig studies.
Carcinogenicity
The ingredients in this product, present at equal to or greater than 0.1% of the product, are not listed by OSHA, NTP, or IARC
as known or suspect carcinogens.
Reproductive Toxicity
None known.
Teratogenicity and Embryotoxicity
None known.
Mutagenicity
None known.
Name of Toxicologically Synergistic Products
None known.
Additional Information
No additional information
SECTION 12: ECOLOGICAL INFORMATION
Discharge to waterways may kill fish. Waste from this product may present long-tem environmental hazards, thus landfill
disposal must be considered less acceptable than incineration.
Additional Information
This product is not expected to present an ecological hazard when used under reasonable conditions and as-intended/as-
designed by the manufacturer.
SECTION 13: DISPOSAL CONSIDERATIONS
Follow local, State/Provincial, and Federal/National regulations applicable to as-used, end-
WASTE DISPOSAL METHOD:
of-life characteristics to be determined by end-user. Material may be polymerized in bucket
by adding 15 parts of Powercrete J60 Part B to each 100 parts of Powercrete J60 Part A by
weight, or 4 parts Part A to 1 part Part B by volume, and thoroughly mix. Set outdoors until
mixture is set up and cooled down.
Not Applicable to finished Part A product as manufactured for distribution into commerce.
US-EPA HAZARD CLASS:
Additional Information
No additional information. This product is not expected to present a hazard when disposed under reasonable conditions of
end-use and in accordance with applicable law.
SECTION 14: TRANSPORT INFORMATION
GROUND 鈥? US-DOT/CAN-TDG/EU-ADR/APEC-ADR
Proper Shipping Name Polyamines, liquid, corrosive, n.o.s. (aliphatic polyamines)
Hazard Class Class 8 ID Number UN2735
Powercrete J Part B Revision 5 Revision Date: July 3, 2006 PAGE 5 OF 7
Packing Group III Labels Corrosive
AIRCRAFT 鈥? ICAO-IATA
Proper Shipping Name Polyamines, liquid, corrosive, n.o.s. (aliphatic polyamines)
Hazard Class Class 8 ID Number UN2735
Packing Group III Labels Corrosive
VESSEL 鈥? IMO-IMDG
Proper Shipping Name Polyamines, liquid, corrosive, n.o.s. (aliphatic polyamines)
Hazard Class Class 8 ID Number UN2735
Packing Group III Label Corrosive
Additional Information
No additional information. Note that transport requires proper packaging and paperwork, including the Nature and Quantity of
goods, per applicable origin/destination/customs points as-shipped.
SECTION 15: REGULATORY INFORMATION
U.S. FEDERAL REGULATIONS
TSCA Section 8b 鈥? Inventory Status: All chemicals comprising this product are either exempt or listed on the TSCA
Inventory.
TSCA Section 12b 鈥? Export Notification: This product contains the following chemicals subject to TSCA Section 12b
export notification.
Chemical CAS #
None
CERCLA (COMPREHENSIVE RESPONSE COMPENSATION, AND LIABILITY ACT)
Chemicals present in the product at a level which could require reporting under the statute:
Chemical CAS #
None
SARA TITLE III (SUPERFUND AMENDMENTS AND REAUTHORIZATION ACT)
This product contains the following chemicals subject to the reporting requirements of Section 313 of SARA Title III.
Chemical CAS #
None
CERCLA SECTION 311/312 HAZARD CATEGORIES:
Fire Hazard No
Pressure Hazard No
Reactivity Hazard No
Immediate Hazard Yes
Delayed Hazard Yes
STATE REGULATIONS
California Proposition 65
This product contains the following chemicals known to the State of California to cause cancer, birth defects, or other
reproductive harm:
Chemical CAS No. % Wt
None
Additional Information
No additional information. This product may be regulated under additional regulations and laws not identified above, such as
for uses other than described or as-designed/as-intended by the manufacturer, or for distribution outside of the USA.
SECTION 16: OTHER INFORMATION
OTHER INFORMATION
Not Applicable.
Sources of Information
International Agency for Research on Cancer (1987), IARC Monographs on the Evaluation of Carcinogenic Risks to
Humans: Overall Evaluations of Carcinogenicity: An updating of IARC Monographs Volumes 1-42, Supplement 7, Lyon,
France.
American Conference of Governmental Industrial Hygieneists (2004), Threshold Limit Values for Chemical Substances
and Physical Agents & Biological Indices.
Powercrete J Part B Revision 5 Revision Date: July 3, 2006 PAGE 6 OF 7
PREPARATION INFORMATION
DATE OF ISSUE: July 3, 2006 SUPERSEDES: February 11, 2005.
DISCLAIMER
Covalence adhesives makes no warranties as to the accuracy or completeness of this information and disclaims
any liability in connection with its use. Covalence Adhesive鈥檚 obligation shall be only as set forth in Covalence
Adhesive鈥檚 standard terms and conditions of sale for this product. In no case will Covalence Adhesives be liable
for any incidental, indirect or consequential damages arising out of the sale, resale, use or misuse of the
product.
The information presented herein was prepared at Covalence / Adhesives by qualified technical personnel, and
to our knowledge it is true and accurate. The information and recommendations are furnished for this product
with the understanding that the purchaser will independently determine the suitability of the product for this
purpose. The data do not constitute a warranty, expressed or implied, statutory or otherwise, nor are they a
representation for which Covalence / Adhesives assumes legal responsibility. The data are submitted for the
user鈥檚 information and consideration only. Any use of this product must be determined by the user to be in
accordance with the applicable federal, state, and local laws and regulations.
END
Covalence Corporation Covalence Specialty Materials Europe
25 Forge Parkway Nieuwlandlaan B15
Franklin, MA 02038 USA B-3200 Aarschot, Belgium
Tel: +1 508-918-1600 Tel: +32 16 55 36 00
US Toll Free: +1 800-248-7659 Fax: +32 16 55 36 74
Fax: +1 508-918-1910 E-mail: CPGE@covcorp.com
E-mail: CPG@covcorp.com
Powercrete J Part B Revision 5 Revision Date: July 3, 2006 PAGE 7 OF 7
|