Resilient Tile Floor Sealers
First Step
Acrylic Floor For Use On:
Sealer Linoleum
Vinyl Tile
Rubber Tile
Vinyl Asbestos
Asphalt Tile
DESCRIPTION
An all-acrylic floor sealer formulated to provide a hard, durable
undercoat for use prior to the application of any floor polish.
Never yellows and will continue to protect your floor after all floor
finish or wax has worn off.
DIRECTIONS
Make sure floor has been thoroughly stripped and rinsed and
allowed to dry. For porous or well-worn floors, apply 2 coats of
sealer followed by 2 or more coats of finish depending on the
gloss desired.
On new floor or floors in good condition, one coat of sealer
should suffice.
This product meets the maximum content requirements for
Volatile Organic Compounds (VOCs) as established by state
and Federal regulations.
PRODUCT SPECIFICATIONS
Type: Modified acrylic Detergent Resistance: Excellent
Stain Resistance: Good
Non-volatile solids: 18.0卤0.5%
Chemical Resistance: Good
Color: Milky white
VOC Content: 0.31 lbs./gal.
Odor: Mild
Storage/Stability: 2 years
pH: 8.5 - 9.0
Freeze/Thaw Stability: Keep from freezing
Dry/Recoat Time: 30 minutes
Weight per Gallon: 8.56 lbs./gal.
Slip Resistance: .5 min. by ASTM D2047
1000-1500 ft2 per gal.
Coverage:
Leveling: Excellent
1500-2000 ft2 per gal.
Sediment: 0.1% by volume, max.
Removability: With conventional
strippers
Misco Products Corporation 鈥? Reading, PA 鈥? (800) 548-4568 FAX (610) 926-1194
www.miscoprod.com
FIR MATERIAL SAFETY DATA SHEET N/A=Not Applicable
Prepared by: Regulatory Affairs Dept. Effective Date: 5/99 Revision: n/a
(Prepared According to 29 CFR 1910.1200)
SECTION 1-PRODUCT IDENTIFICATION AND SUPPLIER INFORMATION
Product Name: First Step
Manufacturer's Name:
Misco Products Corporation Generic Name: Acrylic Floor Sealer
Manufacturer's Address: Chemical Family: Acrylic Wax Blend
1048 Stinson Drive Reading, PA 19605 Formula: Proprietary
Manufacturer's Phone #: (610) 926-4106
SECTION 2-INGREDIENT INFORMATION
CHEMICAL NAME CAS NO. WT. % PEL TWA-TLV STEL-TLV
Water 7732-18-5 to 100
Acrylic Copolymer Dispersion 63744-68-3 35 to 40
Resin Solution 65405-63-2 5 to 10
Polyethylene Wax 68441-17-8 5 to 10
Tributoxy Ethyl Phosphate 78-51-3 0 to 5
Diethylene Glycol Monomethyl Ether 111-77-3 0 to5
SECTION 3-PHYSICAL DATA SECTION 4-FIRE AND EXPLOSION HAZARD DATA
Flash Point (Method Used): N/A
Boiling Point (掳F): 212 F. Specific Gravity: 1.028
Upper Explosion Limit: N/A Lower Explosion Limit: N/A
Vapor Pressure: 20mm Hg @ 68 F. Vapor Density (Air=1): >1
Extinguishing Media: N/A
% Volatile: 82 + pH: 8.6 +/- 0.5
Special Firefighting Procedures: Non Flammable
Solubility in Water: Complete Evaporation Rate (Water=1): <1
Unusual Fire and Explosion Hazards: N/A
Physical Description: Thin milky liquid with characteristic odor.
SECTION 5-REACTIVITY DATA
Stability: Stable Hazardous Polymerization: None
Hazards Decomposition Products: Will not occur. Incompatibility (Materials to Avoid): None
SECTION 6-STORAGE AND HANDLING INFORMATION
Keep out of reach of children. For use by trained personnel only. Keep unauthorized personnel away when applying to floor. Keep container closed during storage. For
institutional and industrial use only. Avoid contact with eyes, skin and clothing. Wear protective gloves, eyewear and footwear when applying. Avoid breathing of
vapors. Use in well-ventilated area.
SECTION 7-HEALTH HAZARDS AND FIRST AID SECTION 8-SPECIAL PROTECTION INFORMATION
Effects of Overexposure: Respiratory Protection: Use in well-ventilated area.
Skin: Prolonged or repeated contact may cause dermatitis. Ventilation Requirements: Provide local exhaust to keep TLV of Section 2 in-
Eyes: Eye irritant. May cause redness or swelling. gredients below acceptable limit.
Inhalation: Vapors may irritate nose, throat and lungs. May cause dizziness, Protective Gloves: Chemical resistant rubber or neoprene.
headache, and nausea. Eye Protection: Chemical splash goggles recommended.
Ingestion: May be irritating to the mouth, throat, and gastrointestinal system. Other Protective Equipment: Eyewash should be nearby. Wear rubber boots and
Vomiting and diarrhea expected with large doses. protective outerwear when using.
First Aid Procedures: SECTION 9-SPILL OR LEAK PROCEDURES
Skin: Flush with water. Seek medical attention if irritation persists. Steps to be taken in Case Material is Released or Spilled: Floors will become
slippery. Avoid walking in product. Keep unessential personnel away. Mop up or
Eyes: Flush with large quantities of water, holding eyelids open. Seek medical
otherwise absorb and hold disposal. Avoid discharge to sewer or open waterways.
attention.
Waste Disposal Method: Any method in accordance with local, state and federal
Inhalation: Remove victim to fresh air and monitor.
laws. Best method is to recycle or reuse for intended purpose. Consult local
Ingestion: Dilute with 2 glasses of water. Seek medical attention if symptoms
authorities for disposal in public sewer. Do not dispose of into storm drain, stream,
persist.
river or to ground. Rinse container thoroughly before discarding in trash.
SECTION 10-REGULATORY INFORMATION
HMIS Hazardous Materials
SARA Title III - Section 311/312 -Hazard Categories: Shipping Information:
No - Fire Hazard FOR CONTAINERS > 1 Gallon : Liquid Floor Wax Identification System
No - Sudden Release of Pressure Hazard Health 1
No - Reactivity Hazard FOR 1 GALLON CONTAINERS : Liquid Floor Wax Flammability 0
Yes - Immediate (acute) Health Hazard Reactivity 0
No - Delayed (chronic) Health Hazard FOR CONTAINERS < 1 GALLON : Liquid Floor Wax Personal Protection A
FOR EMERGENCY MEDICAL OR TRANSPORT INFORMATION: CHEM-TEL, Inc. @ 800-255-3924 (24 hours, 7 days per week)
This product contains the following toxic chemical(s) subject to the reporting requirements of section 313 of the Emergency Planning and Community Right-To-Know Act
of 1986 and of 40 CFR 372.
CAS# Chemical Name Percent by Weight
None
This product contains the following chemical(s) which have been established to be either a carcinogen or suspected carcinogen.
CAS# Chemical Name Percent by Weight
None
SECTION 11-OTHER INFORMATION
This company cannot anticipate all conditions of handling and use of this product. Therefore, this company accepts no responsibility for results obtained by the
application of this information, or the safety and suitability of our products either alone or in combination with other products. It is the responsibility of the user to
provide a safe workplace, using the health and safety information contained herein as a guide. This company will accept no liability for damages or loss incurred from the
improper handling and use of this product
|