FLOOR COATING AND FINISHING MATERIAL
AS TO SLIP RESISTANCE ONLY
17SU
Prime Time
Wood Floor Care
WF
For Use On:
Wood Gymnasium Floors
Cork Parquet Floors
DESCRIPTION
A 100% oil-modified urethane wood finish dispersed in water with characteristics
Waterbased Oil
equal to and often surpassing those of conventional solvent coatings. Specifically
designed to be used on sports, commercial and residential floors where demands
for low odor and VOC compliance are specified. Fast air drying film allows multiple
Modified Urethane
coats daily. Produces a crystal clear film with exceptional gloss. It is compatible
over a wide variety of conventional solvent based and water based urethane and
epoxy coatings (provided that these coatings are cured, bonded and the floor is
Wood Finish
properly prepared. Not compatible over acrylic floor finishes). In addition, NO
catalyst is required (this product cures via oxidation - like conventional oil-modi-
fied urethanes) to produce a finish that provides exceptional durability and scuff
resistance. Maple Flooring Manufacturers Association (MFMA) certified and
approved for use on wood gymnasium floors.
Manufacturer鈥檚 Recommendation: This coating is to be applied without
thinning.
VOC Content = 180 grams/liter, excluding water
DIRECTIONS
FOR NEW WOOD FLOORING OR RENOVATING OLD FLOORS: Abrade previ-
ously coated floors using a #100 or #120 grit screen disk and vacuum thoroughly.
Tack rag using only water and allow floor to dry thoroughly. Apply a medium to thin
coat of finish to the floor using a heavy weight floorcoater with a waterbased finish
pad or gravity fed applicator with a waterbased finish pad. Allow to dry 1 to 2 hours
(depending on weather conditions), before applying the next coat. Three to four
coats of finish are recommended to produce optimum gloss and wear. Screening
between coats is only necessary if the prior coat has dried longer than 8 hours.
Allow 24 hours curing time prior to the return of normal traffic. Allow one week (7
days) curing for heavier traffic. Clean-up using warm water and mild soap.
NOTE: Best results are obtained with adequate ventilation and floor temperature
between 60掳F. and 95掳F. During drying, avoid direct drafts on floor. Do not pour
unused product back into container.
PRODUCT SPECIFICATIONS
Non-volatile solids: Drying Properties: Touch-45 min.
30.0卤0.5%
Color: Milky White Recoat-1 hr.
Odor: Mild Traffic- 24 hrs.
Type: Recoatability:
Oil-modified urethane Excellent (follow directions)
VOC Content:
dispersion 180 gm/liter
pH: Storage/Stability:
7.5 - 8.0 Keep from freezing
Viscosity: Weight per Gallon:
A-C, Gardner 8.42 lbs./gal.
Slip Resistance: Coverage:
Greater than 0.50 400-800 ft2 per gal.
Sward Hardness: Greater than 30 (dependent on type of applicator used)
Chemical Resistance: Excellent
Misco Products Corporation Reading, PA (800) 548-4568 FAX (610) 926-1194
www.miscoprod.com
PRI MATERIAL SAFETY DATA SHEET N/A=Not Applicable
Prepared by: Regulatory Affairs Dept. Effective Date: 4/05 Revision: n/a
(Prepared According to 29 CFR 1910.1200)
SECTION 1-PRODUCT IDENTIFICATION AND SUPPLIER INFORMATION
Manufacturer鈥檚 Name: Product Name: Prime Time Supplier鈥檚 Name:
Misco Products Corporation Generic Name: Waterbased Urethane Wood Finish
Manufacturer鈥檚 Address: Supplier鈥檚 Address:
Chemical Family: Urethane Dispersion
1048 Stinson Drive Reading, PA 19605 Formula: Proprietary
Manufacturer鈥檚 Phone #: (610) 926-4106 Supplier鈥檚 Phone #:
SECTION 2-INGREDIENT INFORMATION
CHEMICAL NAME CAS NO. WT. % PEL TWA-TLV STEL-TLV
Water 7732-18-5 to 100
Oil Modified Urethane Dispersion N/A 25 to 30
N-Methyl Pyrrolidone 872-50-4 0 to 5 100 ppm 100 ppm
Polyether Modified Dimethylpolysiloxane N/A > 0.1
SECTION 3-PHYSICAL DATA SECTION 4-FIRE AND EXPLOSION HAZARD DATA
Flash Point (Method Used): N/A
Boiling Point (掳F): 212 F. Specific Gravity: 1.01
Upper Explosion Limit: N/A Lower Explosion Limit: N/A
Vapor Pressure: 20mm Hg @ 68 F. Vapor Density (Air=1): >1
Extinguishing Media: N/A
% Volatile: 65+ pH: 7.5-8.0
Special Firefighting Procedures: Non Flammable
Solubility in Water: Dispersible Evaporation Rate (Water=1): <1
Unusual Fire and Explosion Hazards: N/A
Physical Description: Moderately viscous milky liquid with characteristic odor.
VOC Content (Subpart D 搂59.406) : 180 g/l
SECTION 5-REACTIVITY DATA
Stability: Stable Hazardous Polymerization: May occur through oxidation, leading to exothermic
reaction. Heat generated by oxidation may lead to spontaneous combustion of
materials such as rags, paper towels, etc., used for clean-up.
Hazards Decomposition Products: Will not occur. Incompatibility (Materials to Avoid): None
SECTION 6-STORAGE AND HANDLING INFORMATION
Keep out of reach of children. For use by trained personnel only. Keep unauthorized personnel away when applying to floor. Keep container closed during storage. For
institutional and industrial use only. Avoid contact with eyes, skin and clothing. Wear rubber gloves when handling. Wear protective rubber boots when applying to
floor. Avoid breathing of vapors. Use in well-ventilated areas at all times.
SECTION 7-HEALTH HAZARDS AND FIRST AID SECTION 8-SPECIAL PROTECTION INFORMATION
Effects of Overexposure: Respiratory Protection: Use in well-ventilated area. Organic vapor respirator
Skin: Prolonged or repeated contact may cause dermatitis. when using in poorly ventilated areas.
Eyes: Eye irritant. May cause redness or swelling. Ventilation Requirements: Provide local exhaust to keep TLV of Section 2 in-
gredients below acceptable limit. Open doors and windows during use. Continue to
Inhalation: Prolonged breathing of vapors may cause dizziness, nausea, and
ventilate during drying period.
headaches.
Protective Gloves: Rubber or chemical resistant gloves should be worn.
Ingestion: May be irritating to the mouth, throat, and gastrointestinal system.
Vomiting and diarrhea expected with large doses. Eye Protection: Splash goggles should be worn when handling.
Other Protective Equipment: Eye wash station should be made available nearby.
Chemical resistant footwear (rubber boots) when using product on floor.
First Aid Procedures: SECTION 9-SPILL OR LEAK PROCEDURES
Steps to be taken in Case Material is Released or Spilled: Floors will become slippery.
Skin: Flush with water, then wash with mild soap and water. Seek medical
Avoid walking in product. Keep unessential personnel away. Mop up or otherwise absorb
attention if irritation persists.
and hold disposal. Avoid discharge to sewer or open waterways.
Eyes: Flush with large quantities of water, holding eyelids open. Seek medical
Waste Disposal Method: Any method in accordance with local, state and federal laws. Best
attention immediately. method is to recycle or reuse for intended purpose. Consult local authorities for disposal in
Inhalation: Remove victim to fresh air. Seek medical attention if symptoms persist. public sewer. Materials used to absorb product should be soaked in water-filled containers or
Ingestion: Dilute with 2 glasses of water. Seek medical attention immediately. rinsed with water prior to discarding in trash receptacles. Do not dispose of into storm drain,
stream, river or to ground. Rinse container thoroughly before discarding in trash.
SECTION 10-REGULATORY INFORMATION
SARA Title III - Section 311/312 -Hazard Categories: Shipping Information: HMIS Hazardous Materials
No - Fire Hazard FOR CONTAINERS > 1 Gallon : Floor Wax Identification System
No - Sudden Release of Pressure Hazard Health 2
No - Reactivity Hazard FOR 1 GALLON CONTAINERS : Floor Wax Flammability 0
Yes - Immediate (acute) Health Hazard Reactivity 0
No - Delayed (chronic) Health Hazard FOR CONTAINERS < 1 GALLON : Floor Wax Personal Protection B
FOR EMERGENCY MEDICAL OR TRANSPORT INFORMATION: CHEM-TEL, Inc. @ 800-255-3924 (24 hours, 7 days per week)
This product contains the following toxic chemical(s) subject to the reporting requirements of section 313 of the Emergency Planning and Community Right-To-Know Act
of 1986 and of 40 CFR 372.
CAS# Chemical Name Percent by Weight
None
This product contains the following chemical(s) which have been established to be either a carcinogen or suspected carcinogen.
CAS# Chemical Name Percent by Weight
None
SECTION 11-OTHER INFORMATION
This company cannot anticipate all conditions of handling and use of this product. Therefore, this company accepts no responsibility for results obtained by the
application of this information, or the safety and suitability of our products either alone or in combination with other products. It is the responsibility of the user to
provide a safe workplace, using the health and safety information contained herein as a guide. This company will accept no liability for damages or loss incurred from the
improper handling and use of this product.
|