MATERIAL SAFETY DATA SHEET
Shield Industries, Inc. 131 Smokehill Lane Woodstock, GA 30188
Day Telephone: (770) 517-6869 Emergency Telephone: 1-800-535-5053
ForceField庐 MoldBlock鈩? - Mold & Mildew Inhibitor Concentrate
鈩?
Section I Product Identification
Product ID: F MBLC
Last Revision Date: 08/01/01
Preparer: R. Lasnik, Vice President
Generic Description: Aqueous Organosilane
Physical Form: Liquid
Color: Colorless to pale yellow
EPA Registration Number: 70871-5-72251
- - - - - - - - - Composition, Information on Ingredients - - - - - - - - - -
Section II Hazardous Ingredients
N/A - Not Available CAS#= Chemical Abstract Service Number
INGREDIENTS CAS # TWA STEL % by Weight
Octadecylaminodimethyltrimethoxysilylpropyl 27668-52-6 N/A N/A 5%
ammonium chloride
Methanol (methyl alcohol) 67-56-1 200 ppm 250 ppm <3
Chloropropyltrimethoxysilane 2530-87-2 0.1 ppm N/A <3
Note: The above information is not intended for use in preparing product specifications.
Section III Hazards Identification Emergency Overview
Appearance and Odor: Colorless to pale yellow liquid, odorless to slight alcoholic
Primary Routes of Entry: Skin contact, Eye contact, Inhalation
This material contains the following components with the special hazards listed below .
Carcinogens Teratogens Reproductive Toxins Sensitizers
None Known None Known None Known None Known
Mutagens
Chloropropyl trimethoxysilane; CAS# 2530-87-2; Positive in the Ames Test; Genetically Active in VIVO Assay
Comments: Chloropropyltrimethoxysilane. was found to be genetically active via inhalation in a bone marrow
micronucleus assay (female rats exposed to 200 ppm/day for 28 days). In the same assay, no evidence of genetic activity
was found in mice exposed to 500, 1000 or 1625 mg/kg by I.P. injection. The potential relevance of this to humans has
not yet been determined.
Section IV First Aid Measures
Warning
Signal Word:
Emergency First Aid Procedures:
IF IN EYES - Hold eyelids open and flush with a steady, gentle stream of water for 15 minutes. Get medical attention.
IF INHALED - Remove victim to fresh air. If not breathing, give artificial respiration, preferably mouth-to-mouth. Get
medical attention.
IF SWALLOWED - Call a doctor or get medical attention. Do not induce vomiting or give anything by mouth to an
unconscious person. Drink promptly a large quantity of milk, eggwhites, gelatin solution, or if these are not available, drink
large quantities of water. Avoid alcohol.
IF ON SKIN - Wash thoroughly with soap and water. Get medical attention if irritation or ill effects develop or persist.
Section V Fire Fighting Measures
Physical and Chemical Characteristics (Fire and Explosion Data)
Boiling Point (760 MM HG)......................... N/A
Specify Gravity (At 68潞F/20oC)........鈥︹?︹??. 1.0 g/mL
Vapor Pressure 鈥︹?︹?︹?︹??..................... N/A
Viscosity (At 68oF/20oC)鈥︹?︹?︹?︹?︹?︹?? 393 mPa鈭僺
pH (approximately)鈥︹?︹?︹?︹?︹?︹?︹?︹??. 5
Solubility in Water........................................ Complete
Reactivity in Water....................................... None
Appearance and Odor................................... Pale yellow liquid, slight alcoholic odor
Flash Point..................................................... N/A
Flammable or Explosive Limits N/A
Unusual Fire & Explosion Hazards鈥︹?︹?︹??. N/A
Hazardous Polymerization............... Will not occur
Section VI Accidental Release Measures
Steps to be taken if material is released or spilled: Do not contaminate water, food, or feed by material.
Water Disposal Methods: Dispose according to Federal RCRA and applicable state and local regulations.
Disposal of collected product, residues, and cleanup materials may be governmentally regulated. Observe all applicable local,
state, and federal waste management regulations.
Inactivation of solutions containing ForceField庐 MoldBlock鈩? may be accomplished by addition of an anionic surfactant or
detergent in quantity equivalent to that of ForceField庐 MoldBlock鈩? in solution.
Section VII Handling and Storage
Handling: Hazard to humans and domestic animals. Causes substantial but temporary eye injury. Do not get in eyes or on
clothing. Wear protective eyewear (goggles, face shield, or safety glasses). Harmful if swallowed, inhaled or absorbed
through skin. Avoid contact with skin, eyes and avoid breathing dust, vapor or spray mist. Wash thoroughly with soap and
water after handling. Remove contaminated clothing and wash clothing before reuse.
Precautions to be taken in handling and storage - Do not freeze product
De-activation for disposal - addition of an anionic surfactant in quantity equal to ForceField庐 MoldBlock鈩? in solution.
Do not contaminate water, food, or feed by storage and disposal.
Section VIII Exposure Controls, Personal Protection
Engineering Controls: Recommended
General Ventilation: Recommended
Personal Protective Equipment (PPE):
Respiratory Protection: Utilize respiratory protective equipment in accordance with 29
CFR1910.134 if other protective measures do not adequately control exposures.
Eye Protection: Safety goggles and face shield or safety glasses with side shields.
Skin protection: Wear chemical resistant, impervious gloves such as PVC coated or butyl rubber.
Section IX Physical and Chemical Properties
Physical Form: Clear liquid Color: Light yellow
Odor: Odorless or slight alcoholic Boiling Point: N/A
Freezing Point: N/A- do not freeze product Solubility in Water: Complete
Volatile Content (>0.1 mmHg): <10%
Section X Stability and Reactivity
Chemical Stability: Under normal conditions this material is stable. Product should not be frozen.
Hazardous Polymerization: Hazardous polymerization will not occur
Incompatibility: Acids, alkalis, strong oxidizing agents and anionic surfactants.
Section XI Disposal Considerations
Contaminated product/soil/water may be RCRA/OSHA hazardous waste. Landfill solids at permitted sites. Disposal of
collected product, residues, and cleanup materials may be governmentally regulated. Observe all applicable local, state, and
federal waste management regulations.
Inactivation of solutions containing ForceField庐 MoldBlock鈩? may be accomplished by addition of an anionic
surfactant or detergent in quantity equivalent to that of ForceField庐 MoldBlock鈩? in solution.
Section XII Transport Information
Dot Information: Not Regulated
Section XIII Regulatory Information
US Federal Regulations
TSCA (Toxic Substances Control Act) Status:
One or more of the components of this product may not be listed on the TSCA inventory of chemical substances.
CERCLA RQ - 40 CFR 302.4(a): Methanol 67-56-1 5000 Lb RQ
SARA 302 Components - 40 CFR 355 Appendix A: None
Section 311/312 Hazard Class - 40 CFR 370.2
Acute: Yes Chronic: Yes Fire: Yes
Pressure: No Reactive: No
Section 313 Components - 40 CFR 372.65: Methanol 67-56-1
Section XIV Other Information
This information is offered in good faith as typical values and not as product specification. No warranty, expressed or
implied is hereby made. The recommended industrial hygiene and safe handling procedures are believed to be generally
applicable. However, each user should review these recommendations in the specific context of the intended use and
determine whether they are appropriate.
* * * * * This is the last Page * * * * *
|