PRODUCT DATA
955
Prime & Seal Bond Coat
SOLVENT ACRYLIC 鈥? EXTERIOR 鈥? SATIN 鈥? 955
Vehicle Type
Product Description Solvent Acrylic
Prime & Seal Bond Coat is a superior quality exterior solvent acrylic primer
Finish
recommended for use on properly prepared masonry, concrete and stucco Satin 鈥? 60掳 Sheen - 20 to 30
(sheen can vary due to porosity)
surfaces and is specifically designed for concrete tilt-up construction.
Prime & Seal Bond Coat is formulated for excellent penetration and
Use - Exterior
adhesion over cured or uncured tilt-up concrete when removal of form
Percent Solids By Weight
release agents and laitance are not feasible. Prime & Seal Bond Coat is
51.1% 卤 2%
designed for use in residential, architectural and commercial applications
Percent Solids By Volume
36.1% 卤 2%
Performance
Suggested Coverage
鈥? Excellent adhesion
250 - 400 SFPG
鈥? Resistant to moisture and moisture vapor (depending on porosity)
鈥? Tolerates slight surface moisture (not soaking wet)
Dry Film Thickness
鈥? Excellent resistance to blistering/cracking/chipping/peeling 1.4 - 2.3 mils @ 250 - 400 SFPG
鈥? Good flow and leveling properties (depending on porosity)
鈥? Excellent resistance to alkali and efflorescence
Viscosity - 68 KU 卤 5
May be applied to properly prepared... Flash Point - 80掳 F.
鈥? Cured and Uncured Masonry and Stucco including: VOC
Cement Plaster and Poured and Precast Concrete Maximum 5.8 lbs./gal. (700 gms./ltr.)
Complies with all Federal, State
and Local VOC standards.
Limitations
Application Equipment
Not for use on driveways, garage floors, walkways or other foot or vehicle
Brush, roller, airless spray
traffic areas. Do not use for immersion service, below grade substrates,
Drying Time
where hydrostatic pressure is expected or where a failure from water
At 75掳F. / 50% RH
intrusion may occur (decorative, planter or perimeter walls). 2 hours to touch
4 hours to recoat
Colors
White
Products Included in This Line
955 White
Product Index 鈥? Category 3
COLOR WHEEL PAINT MANUFACTURING COMPANY, INC.
2814 Silver Star Road 鈥? Orlando, Florida 32808
Exterior Primers, Sealers
407-293-6810 鈥? 800-749-6810 鈥? Fax 407-293-0945
& Conditioners
www.colorwheel.com
09900
0955.04.1 / PDS / 1
955 PRIME & SEAL BOND COAT 鈥? SOLVENT ACRYLIC 鈥? EXT 鈥? SATIN
Surface Preparation General Application Safety
The performance of this product is critically Mix thoroughly to a uniform consistency before CAUTION: Combustible. Contains Xylene.
dependent upon the soundness of the substrate each use. Apply by brush, roller, or airless Keep away from heat and open flame. Harmful
to which it is applied. It has been determined sprayer. Work material vigorously into pores. vapors. May affect the brain or nervous system
that as high as 80% of all paint and coating Maintain a wet edge. If roller application is causing headaches or nausea.
failures may be attributed to improper surface employed on porous surfaces, final passes
WARNING! HARMFUL IF INHALED.
preparation. It is essential that the proper steps should be completed in a downward direction
SEE LABEL OR MSDS FOR LIST OF
be taken before applying this product. to insure a uniform appearance and texture.
HAZARDOUS INGREDIENTS. KEEP OUT OF
Apply at such a rate as to avoid runs and sags.
General: REACH OF CHILDREN! May cause eye, skin,
If airless spray application is employed on
Surface can be slightly damp during application nose and throat irritation. To avoid breathing
porous surfaces, immediate 鈥渂ack rolling鈥? and
but should in sound condition. Surface should vapors or spray mist, open windows and doors
鈥渂ack brushing鈥? with wet roller/brush is
be clean and free from dirt, grease, mill oils, or use other means to insure fresh air entry
recommended to help reduce pinholing and
rust, mill scale, chalky paint, efflorescence, during application and drying. If you experience
work material into pores.
organic growth, mildew, and foreign matter to eye watering, headaches or dizziness, increase
insure good adhesion of primers and/or finish Thinning: fresh air or wear respiratory protection (NIOSH/
coats. All unpainted substrates should be Thinning is not recommended. MSHA TC 23C or equivalent) or leave area.
properly prepared according to respective Close container after each use. Avoid contact
Application Equipment
manufacturer鈥檚 and / or supplier鈥檚 with eyes and skin.
recommendations. Thoroughly review and Brush: Use a quality China bristle brush.
First Aid
follow Color Wheel 鈥淪urface Preparation
Roller: Use lambswool or synthetic cover with
Guidelines鈥? and/or Color Wheel written If you experience difficulty in breathing, leave
an 1/4" to 1 1/4" nap, depending on surface
specification before applying. the area to obtain fresh air. If continued difficulty
texture.
is experienced, get medical assistance
Airless Spray: Use a tip size of between 0.013" immediately. In case of eye contact, flush
and 0.015". Tip size should reflect equipment immediately with plenty of fresh water for at
type and pressure, applicator technique and least 15 minutes and get medical attention; for
surface conditions. Adjust pressure for constant skin, wash thoroughly with soap and water. If
and proper atomization. swallowed, DO NOT INDUCE VOMITING.
Get medical attention immediately.
Cleanup: Clean all tools and equipment with
xylene/xylol immediately after use. Flush spray Storage and Handling
equipment thoroughly.
Keep from freezing or exposure to intense heat.
Curing Do not transfer contents to unlabeled container.
Drying time and curing affect the performance Technical Services
of product. Do not apply when air, surface or
Color Wheel Paints and Coatings offers and
product temperatures are below 50掳F. or above
encourages the use of our free technical service.
100掳 F. Surface temperature must be at least
We also advise you to contact us regularly for
5掳 F. above dew point. Plan ahead and avoid
updates to this and other technical data. For
applying when damp or threatening weather is
technical assistance, to arrange a consultation
expected. Product must cure at least 4 hours
with a Sales Representative, or for current
before being subjected to moisture. During
technical data, consult your yellow pages for
extremely warm weather, maintaining a wet
the Color Wheel location nearest you, or call
edge may become difficult. Avoid application
toll free (800) 749-6810.
during the heat of the day. Do not apply late in
the day where dew or condensation may form
before product begins to cure.
All technical advice, recommendations, and services are rendered by Color Wheel gratis. They are based on technical data which Color Wheel believes to be reliable, and are intended for use by persons having skill and knowhow at their own discretion and
risk. Color Wheel Paint Manufacturing Company, Inc. assumes no responsibility for results obtained or damages incurred from their use by purchaser/user in whole or in part. All information is subject to change without notice.
NOTE: Where applicable, and for consistency, technical data and test results contained in this document are based on the pure white base of the particular product line.
LIMITATION OF LIABILITY: COLOR WHEEL MAKES NO WARRANTY OR GUARANTEE OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
Liability, if any, is limited to replacement of the product or refund of the purchase price. LABOR OR COST OF LABOR AND OTHER CONSEQUENTIAL DAMAGES ARE HEREBY EXCLUDED.
09900 0955.04.1 / PDS / 2
|