PRODUCT DATA
965
UltraCrete Clear Coat
SOLVENT ACRYLIC 鈥? EXTERIOR 鈥? PENETRATING SEALER
M P I 34 & 104 Approved
Product Index 鈥? Category 7
Product Description
Floor Finishes & Concrete Stains
UltraCrete Clear Coat is a superior quality exterior solvent-acrylic
penetrating clear sealer. Designed specifically for use on a variety of
properly prepared new or previously stained concrete surfaces, including
Vehicle Type
patios, pool decks, garage floors, sidewalks and walkways. UltraCrete
Solvent-Acrylic
Clear Coat has unsurpassed penetration and adhesion, is extremely
durable with exceptional resistance to blistering, cracking and peeling, is Finish
highly scrubbable and washable with great stain-resistant properties. Penetrating Sealer
UltraCrete Clear Coat is highly resistant to alkali-burn and efflorescence
Use
and is designed for use as a sealer over our siliconized concrete stains or
Exterior
as a penetrating sealer for concrete floors in residential, multi-family,
architectural, commercial and light industrial applications. Percent Solids By Weight
25% 卤 2%
Performance Percent Solids By Volume
鈥? 20.4% 卤 2%
Excellent adhesion and exceptional long term durability
鈥? Excellent resistance to blistering/cracking/chipping/peeling Suggested Coverage
鈥? Good flow and leveling properties 325-425 SFPG
鈥? Resistant to moisture and moisture vapor Dry Film Thickness
鈥? Good stain resistant properties No greater than 1.0-1.25 mils DFT
per coat, not to exceed a maximum
鈥? Resistant to scuffing/marring
of 2 coats.
鈥? Excellent resistance to alkali and efflorescence
Viscosity
55 KU 卤 5
May be applied to properly prepared...
Flash Point
鈥? Concrete Garage Floors 鈥? Concrete Walkways
80掳 F.
鈥? Concrete Patios 鈥? Concrete Pool Decks
VOC
Exceeds maximum allowable VOC.
Limitations 5.73 lbs./gal. (687 gms./ltr.)
Do not apply to damp concrete surfaces. Do not use for immersion service,
Application Equipment
below-grade, or substrates constantly in contact with moisture. Do not use
Brush, roller, airless or
in highly corrosive or chemical environments, or areas subject to intense conventional spray
heat. Do not use for heavy vehicle traffic or excessive weight (i.e. forklifts
Drying Time
or steel wheels). See Warning on back to insure adequate air ventilation
At 75掳F. / 50% RH
for interior use.
30 minutes to touch
4 hours to recoat
Professional Use Only: This product is designed as a penetrating sealer,
Colors
not a gloss topcoat. Applying in excess amounts will adversely affect the
performance of this product and will void any warranty claims. Clear
Products Included in This Line
Note: Always select and apply a test area if unfamiliar with surface or
965 - Clear
product. User and owner should be aware that non-porous damp, soiled
or incline surfaces may become quite slippery. Therefore user must
determine whether or not a slip-resistant additive should be incorporated
before application of any stain or clear sealers.
2814 Silver Star Road 鈥? Orlando, Florida 32808
Phone 407-293-6810 鈥? Toll Free 800-749-6810 鈥? Fax 407-293-0945
www.colorwheel.com
09900
0965.08.2 / PDS / 1
965 ULTRACRETE CLEAR COAT 鈥? SOLVENT ACRYLIC 鈥? EXTERIOR 鈥? PENETRATING SEALER
Previously Painted Surfaces:
Surface Preparation Safety
Do not apply to damp surfaces. Remove
The performance of this product is critically CAUTION: Combustible. Contains Xylene.
previously painted material from surface by
dependent upon the soundness of the substrate Keep away from heat and open flame. Harmful
vacuum-grit blast (Blastrac), sand or grit blasted
to which it is applied. It has been determined vapors. May affect the brain or nervous system
or mechanically scarified prior to the application
that as high as 80% of all paint and coating causing headaches or nausea.
of any finish materials. This process should
failures may be attributed to improper surface WARNING! HARMFUL IF INHALED.
perform the removal of enough of the surface to
preparation. It is essential that the proper steps SEE LABEL OR MSDS FOR LIST OF HAZARDOUS
create a anchor profile.
be taken before applying this product. INGREDIENTS. KEEP OUT OF REACH OF
Recoat:
General: CHILDREN! May cause eye, skin, nose and
If recoating is required,apply at 325-425 square throat irritation. To avoid breathing vapors or
Surface must be completely dry and in sound
feet per gallon to achieve a dry film thickness of spray mist, open windows and doors or use
condition. Surface should be clean and free from
no greater than 1.0-1.25 mils DFT per coat. Do other means to insure fresh air entry during
dirt, grease, mill oils, rust, mill scale, chalky paint,
not exceed a maximum of two coats; allow 4 application and drying. If you experience eye
efflorescence, organic growth, mildew, and
hours dry time between coats. watering, headaches or dizziness, increase
foreign matter to insure good adhesion of
General Application fresh air or wear respiratory protection
primers and/or finish coats. All unpainted
(NIOSH/MSHA TC 23C or equivalent) or leave
substrates should be properly prepared Mix thoroughly to a uniform consistency before
area. Close container after each use. Avoid
according to respective manufacturer鈥檚 and each use. Apply by brush, roller, or airless sprayer.
contact with eyes and skin.
/ or supplier鈥檚 recommendations. Maintain a wet edge. If roller application is
Thoroughly review and follow Color Wheel First Aid
employed on porous surfaces, final passes
鈥淪urface Preparation Guidelines鈥? and/or Color should be completed in same direction to insure If you experience difficulty in breathing, leave
Wheel written specification before applying. a uniform appearance and texture. Apply at such the area to obtain fresh air. If continued
Recommended Primer/Application a rate as to avoid runs, sags, ropes and puddles. difficulty is experienced, get medical
If airless spray application is employed on porous assistance immediately. In case of eye contact,
New Surfaces:
surfaces, immediate 鈥渂ack rolling鈥? and 鈥渂ack flush immediately with plenty of fresh water
The Florida Concrete & Products Association
brushing鈥? with wet roller/brush is recommended for at least 15 minutes and get medical
recommends that a curing time of no less than
to help reduce pinholing and work material into attention; for skin, wash thoroughly with soap
30 days should be observed before painting
pores. and water. If swallowed, DO NOT INDUCE
new concrete surfaces. Floors should always be
Thinning: VOMITING. Get medical attention
tested for moisture prior to commencement of
Do not thin. immediately.
work. Surface should be clean and free of any
Application Equipment Storage and Handling
foreign matter that may affect the adhesion and
performance of the finish coat and at a safe level Brush: Use a quality China bristle brush. Keep from freezing or exposure to intense
of pH (below 8.5). Roller: Use lambswool or synthetic cover with heat. Do not transfer contents to unlabeled
Non-Porous (trowel finish) concrete should be an 3/16" to 1/2" nap, depending on surface container.
acid etched with 1 part muriatic acid to 8 parts texture. Technical Services
water. Test mixture to insure proper profile, Airless Spray: Use a tip size of between 0.011" Color Wheel Paint offers and encourages the
between 1.5 and 2.0, is obtained. A stronger and 0.013". Tip size should reflect equipment use of our free technical service. We also
mixture may be needed. Apply evenly to all type and pressure, applicator technique and advise you to contact us regularly for updates
areas. Using a course nylon bristle brush, scrub surface conditions. Adjust pressure for constant to this and other technical data. For technical
all areas. Allow to remain for 10 to 15 minutes. and proper atomization. assistance, to arrange a consultation with a
Using a pressure washer, rinse thoroughly to Cleanup: Clean all tools and equipment with Sales Representative, or for current technical
insure all residue has been removed. A second xylene/xylol immediately after use. Flush spray data, consult the Color Wheel location nearest
or third thorough rinse maybe needed to ensure equipment thoroughly. you.
all residue has been removed. Failure to Curing
properly etch and completely rinse the surface
Drying time and curing affect the performance
clean could result in adhesion problems. Allow
of product. Do not apply when air, surface or
twenty-four hours drying time before coating.
product temperatures are below 50掳 F or above
Mix thoroughly to a uniform consistency before
100掳 F. Surface temperature must be at least 5掳 F
each use. Apply at 325-425 square feet per
above dew point. Plan ahead and avoid applying
gallon to achieve a dry film thickness of no
when damp or threatening weather is expected.
greater than 1.0-1.25 mils DFT per coat. Do not
Product must cure at least 4 hours before being
exceed a maximum of two coats; allow 4 hours
subjected to moisture. During extremely warm
dry time between coats.
weather, maintaining a wet edge may become
Professional Use Only: This product is difficult. Avoid application during the heat of
designed as a penetrating sealer, not a gloss the day. Do not apply late in the day where dew
topcoat. Applying in excess amounts will or condensation may form before product
adversely affect the performance of this product begins to cure.
and will void any warranty claims.
All technical advice, recommendations, and services are rendered by Color Wheel gratis. They are based on technical data which Color Wheel believes to be reliable, and are intended for use by persons having skill and knowhow at
their own discretion and risk. Color Wheel assumes no responsibility for results obtained or damages incurred from their use by purchaser/user in whole or in part. All information is subject to change without notice.
NOTE: Where applicable, and for consistency, technical data and test results contained in this document are based on the pure white base of the particular product line.
LIMITATION OF LIABILITY: COLOR WHEEL MAKES NO WARRANTY OR GUARANTEE OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Liability, if any, is limited
to replacement of the product or refund of the purchase price. LABOR OR COST OF LABOR AND OTHER CONSEQUENTIAL DAMAGES ARE HEREBY EXCLUDED.
09900 0965.08.2 / PDS / 2
|