ARCOR
TM
TM
EPOXY TECHNOLOGIES
PRODUCT DATA SHEET
REVISED 05/03
ARCOR® S-15
GENERIC TYPE: AMINE CURED 100% SOLIDS EPOXY PRIMER, TOPCOAT
DESCRIPTION AND RECOMMENDED USES: ARCOR® S-15 is a solvent free bisphenol F coating suitable for immer-
sion and non-immersion service, particularly in aggressive and alkali environments. ARCOR® S-15 produces a tough,
chemical resistant coating on ferrous metals and concrete. As a low viscosity epoxy with excellent flexibility ARCOR®
S-15 is a suitable for large tank linings and secondary containment concrete. Suitable for hand or spray application on
metals or concrete. The long pot-life and over coat window make this ideal for larger surface area application by airless
or plural component spray.
FOR INDUSTRIAL USE ONLY
SPECIFICATION DATA
TEMPERATURE: Immersion service SOLIDS BY VOLUME: 100%
Max.145ºF (49ºC); Spike to 200ºF (79ºC)(3 Hrs).
Dry to 325ºF (149ºC) VISCOSITY:10,000-20,000 cps
POT LIFE: 35 MIN/KG @ 72ºF
CHEMICAL RESISTANCE:
Water: Excellent
MIX RATIO: 2:1 by Volume (Base:Activator) 100 gm:
Alkalies: Excellent
40 gm by weight
Inorganic Acids: Good
Organic Acids: Good
Organic Solvents: Good
COLOR: Gray, Light Gray, Red
SHELF LIFE: 5 Years at 55-95ºF (13-35ºC)
ABRASION: Good
COVERAGE: 80-160 ft2(7.5-15 M2)/ gal / coat
FILM THICKNESS: 6 -8 mils(.15-.20 mm)/coat
Splash: 2 coats, Immersion: 2-3 coats
WEIGHT PER GALLON: 13.6 lbs (6.2 KG, 231 cu.in.)
FLEXIBILITY: Very Good 1-KG Kit @ 37.5 cu.in.
Very good with Polyester Cloth; 1.5 oz/ft2
(.5 KG/M2) ORDER INFORMATION: To place orders
and/or obtain pricing information contact:
APPLICATIONS: Aggressive Chemical Tank
Linings, Acids, Caustics, Alcohols, Demin. ARCOR Epoxy Inc.
Excellent for Secondary Containment’s. PO Box 273
Excellent when force cure is not available. South Dennis, MA 02660
TEL: 800-878-9593; FAX: 888-878-9593
Manufacturer makes no warranty either expressed or implied including warranties of merchantability or fitness for a particular purpose for this product. Under no circum-
stances will the manufacturer be liable for incidental, consequential or other damages, breach of warranty, strict liability, or any other theory arising out of use of this product.
PO Box 273, South Dennis, MA 02660 Tel: 508-385-5598 / 800-878-9593 Fax: 508-385-5798 Internet: www.ArcorEpoxy.com
ARCOR International
TM
EPOXY TECHNOLOGIES TM
APPLICATION SHEET
ARCORâ„? S-15
REVISED 05/03
SEE MATERIAL SAFETY DATA SHEET BEFORE HANDLING THIS PRODUCT
SURFACE PREPARATION:
Steel surfaces are to be abrasive blasted with chloride free abrasive. Exterior applications to SSPC SP-10 Near White metal finish.
Immersion applications to SSPC SP-5 White metal 3 to 5 mil profile. Grind flat all burrs, weld seams, radius sharp edges. Fresh blasted
ferrous surfaces to be primed immediately with ARCORâ„? S-15, S-30 Prime or ARCORâ„? EE-11 Prime to prevent oxidation of sur-
face.
Concrete surfaces should be degreased if oil and grease contamination is present. Degreased surface shall be high pressure washed,
acid etched and high pressure washed again so surface is clean and free of all grease, oils and surface laitance. Existing coatings
should be abrasive blasted to clean concrete. Prime with ARCORâ„? EE-10 or S-15.
MIXING:
Thoroughly mix Activator into Base with mixing stick or drill with low speed mixing blade scraping sides and bottom of container or mix-
ing board. Mix by Volume 2 parts Base to 1 part Activator or by weight 100 grams base to 40 grams activator. Mix thoroughly to pro-
duce an even colored and streak-free material.
THINNING: Add 5-7.5% by volume(6-12 oz.) Acetone or MEK to extend pot-life and/or thin for cold weather application.
APPLICATION:
Brush: medium to stiff bristle of sufficient quality that bristles do not pull out and stick in coating. Trim or tape to <1� nap.
Roller: good quality 1/8� nap.
Plural Spray: .527-.531 tip, 3,000-3,500 PSI, Heat to 150ºF Base, 90ºF Activator. 30 mesh screens. Heated hose @ 120ºF
Airless Spray: .027-.035 tip, 4,000-4,500 PSI(45:1). Add 6-12 oz/gal of MEK or Acetone.(Caution: Short Pot-Life)
Conventional Spray: Not Recommended.
All spray equipment should employ traps to prevent water and oil from contaminating coating and screens to prevent particulate con-
tamination.
APPLICATION TEMPERATURE:
Material: Keep between 55 to 95ºF(17 to 35ºC). Substrate: Keep between 45 to 105ºF(7 to 40ºC). The difference in temperature of
the substrate and the material should never exceed 10ºF(5ºC). Substrate shall be a minimum of 5ºF(3ºC) above dew point. Do not
apply if relative humidity exceeds 90%. If necessary heat metal prior to surface preparation using electric heater or heat lamp. Never
use gas, oil or kerosene heaters as they will leave a greasy residue on metal surface. For best results keep all material in warm area
overnight(75ºF+, 24ºC) for ease of mixing. If necessary base component of material can be heated by microwave for 30-45 seconds for
a 1 KG Base unit or by warm water bath. Heat activator by warm water bath only. If necessary let material cool before application.
OVERCOAT/CURE TIME: By brush, roller or squeegee recoat while material is still soft, but tack-free, between 6-14 hours at
77ºF(25ºC). If overcoat window is exceeded abrade surface with course sandpaper, grinder or brush blast. By spray application recoat
between 2-14 hours at 77ºF. Full cure before immersion 72 hours at 77ºF. Add 30 hours additional cure time for each 10ºF below 77ºF.
Subtract 12 hours of cure time for each 10ºF above 77ºF. Force Cure with heat for best performance for 4 hours at 200ºF(93ºC), 12
hours at 150ºF( 66ºC).
CLEAN UP: Clean tools immediately after use with M.E.K. or similar. Isopropyl Alcohol can be used in solvent restricted areas.
WARNING: Base contains epoxy resin. Activator contains alkaline amines, a strong sensitizer. May cause skin irritation, sensitization or other allergic responses. Use with
good ventilation, particularly if heated or sprayed. Prevent all contact with skin or eyes. Wear protective clothing, goggles, gloves or barrier creams. Keep containers closed
when not in use. Wash thoroughly after handling. In case of skin contact immediately wash with soap and water. In case of eye contact, flush with water for 15 minutes. If irri-
tation persists seek medical attention.
PO Box 273, South Dennis, MA 02660 Tel/Fax: 800-878-9593 /508-385-5798 Email: arcor@ArcorEpoxy.com www.ArcorEpoxy.com
|