ARCOR庐
EPOXY TECHNOLOGIES鈩?
PRODUCT DATA SHEET
REVISED 09/18/01
ARCOR鈩? S-16
GENERIC TYPE: AMINE CURED 100% SOLIDS EPOXY PRIMER, TOPCOAT
DESCRIPTION AND RECOMMENDED USES:
ARCOR鈩? S-16 is a solvent free epoxy coating designed as a protective coating for metals in immersion service.
ARCOR鈩? S-16 produces a tough, chemical resistant, flexible coating that is ideally suited for aggressive water
service(salt, brackish). Enhanced by multi functional chemistry the ARCOR鈩? S-16 is a fine multipurpose coating
suited for moderate acid and caustic service, and is excellent in water environments. A fine general use epoxy.
S-16 is; NSF Certified for Potable Water; USDA for Incidental Food Contact in Meat & Poultry Production;
FDA Guideline CFR 21 Section 175.300 listed for Repeated Food Contact use.
FOR INDUSTRIAL USE ONLY
SPECIFICATION DATA
SOLIDS BY VOLUME: 100%
TEMPERATURE: Immersion service
Max.130潞F(55潞C); Spike to 160潞F(71潞C) (3 Hrs)
VISCOSITY: 130,000 - 260,000 cps
POT LIFE: 30 MIN/Gal @ 72潞F
CHEMICAL RESISTANCE:
Water: Excellent
MIX RATIO: 1.3:1 by Volume (Base:Activator)
Alkalies: Good
100 gm :67.5 gm by weight
Inorganic Acids: Good
Organic Acids: Fair
Organic Solvents: Good COLOR:Top:Blue; Intermediate:Fuschia;Primer:White
SHELF LIFE: 5 Years at 55-95潞F (13-35潞C)
ABRASION: Good
COVERAGE: 20-80 ft2 (1.9-7.5 M2)/gal(theoretical)
FLEXIBILITY: Good
Very Good with Fiberglass Mat; 1.5 oz/ft2 (.5 KG/M2) WEIGHT PER GALLON: 9.7 LBS (4.4 KG)
FILM THICKNESS: 10-20 mils/coat,
ORDER INFORMATION: To place orders
(.25-.50 mm) Immersion: 2 or 3 coats
and/or obtain pricing information contact:
ARCOR Epoxy Inc.
APPLICATIONS: Condensers, Heat Exchangers,
PO Box 273
Circ. Pipe, Water Screens, Pumps, Impellers, Filters,
South Dennis, MA 02660
Valves, Hydro Wheels, Tank Linings, Ion Exchange
TEL: 800-878-9593; FAX: 888-878-9593
Filters Excellent Flexibility.
Manufacturer makes no warranty either expressed or implied including warranties of merchantability or fitness for a particular purpose for this product. Under no circumstanc-
es will the manufacturer be liable for incidental, consequential or other damages, breach of warranty, strict liability, or any other theory arising out of use of this product.
PO Box 273, South Dennis, MA 02660 Tel/Fax: 800-878-9593 /508-385-5798 Email: arcor@ArcorEpoxy.com www.ArcorEpoxy.com
ARCOR庐
EPOXY TECHNOLOGIES鈩?
APPLICATION SHEET
REVISED 09/18/01
ARCOR鈩? S-16
SEE MATERIAL SAFETY DATA SHEET BEFORE HANDLING THIS PRODUCT
SURFACE PREPARATION:
Steel surfaces: Always abrasive blast with chloride free abrasive. Exterior applications to SSPC SP-10 Near White metal
finish. Immersion applications to SSPC SP-5 White metal. Grind flat all burrs, weld seams, radius sharp edges. Fresh
blasted surfaces to be primed with ARCOR鈩? S-30 Prime or ARCOR鈩? S-16 only in NSF, USDA or FDA Applications.
Concrete surfaces : Not Recommended for hand or roller application. Apply by heated plural or airless spray only.
Concrete surfaces should be degreased if oil and grease contamination is present. Degreased surface shall be high pres-
sure washed, acid etched and high pressure washed again so surface is clean and free of all grease, oils and surface
laitance. Existing coatings should be abrasive blasted to clean concrete. Prime with ARCOR鈩? S-16 only in NSF, USDA or
FDA Applications; or ARCOR鈩? EE-70, EE-79 or ARCOR鈩? EE-10.
MIXING:
Thoroughly mix Activator into Base with mixing stick or drill with low speed mixing blade. Mix by Volume 1.3 parts Base to
1 part Activator or by Weight 100 gm Base to 67.5 gm Activator.
THINNING: Never thin.
APPLICATION:
By Brush use medium to stiff bristle of sufficient quality that bristles do not pull out and stick in coating. Trim or tape to
<1鈥? nap.
Roller use good quality 1/8鈥? nap.
Plural Spray use .023-.032 tip, 3,000-3,500 PSI, Heat to 130潞F Base, 110潞F Activator.
Airless Spray Not Recommended
Conventional Spray Not Recommended
All spray equipment should employ traps to prevent water and oil from contaminating coating and screens to
prevent particulate contamination.
APPLICATION TEMPERATURE:
Material: Keep between 55 to 95潞F(13 to 35潞C). Substrate : Keep between 45 to 105潞F (7 to 40潞C). The difference in tem-
perature of the substrate and the coating should never exceed 10潞F (5潞C).
OVERCOAT / CURE TIME:
By Brush or Roller recoat between 6 and 8 hours at 72潞F (22潞C).
When spraying recoat between 5 and 8 hours. Full cure before immersion 3 Days at 72潞F. Force Cure: 12 hours at 120潞F
(49潞C).
CLEAN UP: M.E.K. or similar
WARNING: Base contains epoxy resin. Activator contains alkaline amines, a strong sensitizer. May cause skin irritation, sensitization or other allergic responses. Use with
good ventilation, particularly if heated or sprayed. Prevent all contact with skin or eyes. Wear protective clothing, goggles, gloves or barrier creams. Keep containers closed
when not in use. Wash thoroughly after handling. In case of skin contact immediately wash with soap and water. In case of eye contact, flush with water for 15 minutes. If irri-
tation persists seek medical attention.
PO Box 273, South Dennis, MA 02660 Tel/Fax: 800-878-9593 /508-385-5798 Email: arcor@ArcorEpoxy.com www.ArcorEpoxy.com
|