MATERIAL SAFETY DATA SHEET
FOR METALWORKING FLUID
SECTION I 鈥? PRODUCT IDENTIFICATION
Manufacturer: Desilube Technology, Inc. Information Phone: 610-792-9460
904 Breezewood Lane Emergency Phone: 215-368-2327
Lansdale, PA 19446 Prepared by: J.P. King
Date: July 1, 2007 (Revised)
Trade Name: DESIGREEN PENETRANT
Synonyms: Penetrant, Lubricant or Metalworking fluid
D.O.T. Hazard Class: None
Proper shipping Name: None
SARA hazard: None Noted (Section 311/312) Title III, Section 313 鈥? Not Listed
SECTION II 鈥? INGREDIENTS 鈥? HAZARD CLASSIFICATION
Components 鈥? Hazardous CAS No. % Comments
None as defined under the U.S. OSHA Hazardous Communication (29 CFR 1910.1200) or the
Canadian Hazardous Product Act S.C. 1987, C30 (Part 1)
The precise composition of this product is proprietary information. This biobased penetrant / lubricant has
been formulated with all biodegradable and renewable ingredients. It does not contain heavy metals, zinc,
petroleum oil, sulfur, chlorine or ozone depleted chemicals.
SECTION III 鈥? PHYSICAL DATA
Boiling Point: NE Melting Point: NA
Evap. Rate: Not Determined Specific Gravity 0.9
Volatile: NE Solubility in H2O: Insoluble
Appearance: Light tan clear liquid Freezing Point: NE
Vapor Pressure: NE
SECTION IV 鈥? FIRE AND EXPLOSIVE DATA
HMIS Rating: Health (1) Fire (1) Reactivity (0) Specific (None)
Above 1500C
Flash Point:
Flammable Limit: Lower, NE; Upper, NE
Autoignition Temp: NE
Extinguishing Media: Water-fog, CO2, dry chemical and foam
Special Fire Fighting Procedures: Use self-contained breathing apparatus
Unusual Fire and Explosion Hazards: Rags soaked with any fluid present a fire hazard and should always
be stored in UL listed or Factory Mutual approved, covered containers.
Improperly stored rags can create conditions that lead to oxidation.
Oxidation, under certain conditions can lead to spontaneous combustion.
This product contains antioxidants to retard oxidation.
1
MSDS 鈥? DESIGREEN PENETRANT
SECTION V 鈥? REACTIVITY DATA
Stability: Stable
Conditions Contributing to Instability: NA
Incompatibility: Avoid contact with strong oxidizers. Contact with these materials may result in the
generation of heat or a violent chemical reaction.
Hazardous Decomposition- Thermal and Other:
Thermal 鈥? Oxides of carbon, nitrogen and phosphorus
Conditions to avoid: NA
SECTION VI 鈥? TOXICITY
- Oral: Mixture has not been tested (NE).
- Dermal: NE
- Inhalation: NE
- Toxic Effect / route of Entry
Eye Effects: Irritant
Skin Effects: Irritant
Prolonged contact may cause skin irritation.
- Other Toxic Effects: Inhalation of mists from this product can cause respiratory tract irritation.
- Target Organ Toxin: Eyes, skin and respiratory tract.
- Toxicity Comments: This products does not contain any carcinogens as listed by IARC, NTP,
or OSHA.
SECTION VII 鈥? HEALTH HAZARD INFORMATION
- Permissible Exposure Limits: Permissible exposure limits have not been established for this product.
- Emergency First Aid: Don鈥檛 induce vomiting, give plenty of water, and get medical attention.
- Dermal: Wash with soap and water, remove contaminated clothing and lauder. If redness or irritation
persists, get medical attention.
- Eye Contact: Flush with plenty of water, for at least 15 minutes; hold eyelids open while flushing; get
medical attention.
- Inhalation: Remove to fresh air.
SECTION VIII 鈥? SPECIAL PROTECTION INFORMATION
- Ventilation Requirements: Local exhaust 鈥? use with adequate ventilation. Investigate engineering
techniques to reduce exposure below airborne exposure limits. Provide ventilation of necessary
to control exposure levels below airborne exposure limits. Refer to the exposure limits of
components in this product If practical, use local mechanical exhaust ventilation at source of air
contamination such as open mixing equipment.
- Eye: goggles
- Hand (glove type): Any non-permeable type product
- Respiratory Type: Filters (Mist)
Respiratory protection is normally not needed unless working conditions result in the generation of
mists from this product or solutions of this product. If mists are present, use NIOSH/MSHA
approved dust/mist masks, such as the 3M 8710 or 8715 particulate aspirator. Appropriate eye
protection must be worn when using dust/mist masks.
- Other Protection Equipment: NA
2
MSDS 鈥? DESIGREEN PENETRANT
SECTION IX 鈥? SPECIAL HANDLING AND STORGE CONDITIONS
- Wash thoroughly after handling; do not get in eyes, on the skin or clothing; do not breath dust, vapor,
mist or gas.
- Keep container closed.
- Empty container may contain hazardous residues.
SECTION X 鈥? SPILL MANAGEMENT
- Absorb with sand or inert material; sweep or scoop up and remove; prevent spread of spill; dispose of
immediately.
SECTION XI 鈥? DISPOSAL PRECEDURES
- Consult federal, state or local authorities for proper disposal procedures.
NA 鈥? NOT APPLICABLE
NE 鈥? NOT ESTABLISED
____________________________________________________________________________________
The above information is accurate to the best of our knowledge. However, since data, safety standards, and
government regulations are subject to change and the conditions of handling and use, or misuse, are beyond
our control, Desilube Technology makes no warranty, either express or implied, with respect to the completeness
or continuing accuracy of the information contained herein and disclaims all liability for reliance thereon. User
should satisfy himself that he has all current data relevant to his particular use.
3
|