Date Prepared: 11/12/02
Supersedes: 08/01/01
ChemMasters
Product Name: SpallGuard WB10%
Material Safety Data Sheet
1. Chemical Product and Company Information
Product Name: SpallGuard WB 10%
Product Description: SpallGuard WB 10% is a siloxane moisture and water repellant for concrete and masonary.
ChemMasters In Case of Emergency Contact:
300 Edwards Street CHEMTREC 800/424-9300
Madison, Ohio 44057
440-428-2105
2. Composition / Information on Ingredients
Hazardous Components CAS # Exposure Limits % by Wt
OSHA(PEL/TWA) ACGIH (TLV/TWA) OTHER
Silicone Emulsion Proprietary Conains no hazardous ingredients 20
Water 7732-18-5 NE NE --- 80
3. Hazards Identification
May Cause eye or lung irritation
Harmful if swallowed
Potential Health Hazards - Acute
Eye: Causes eye irritation. Direct contact with the liquid or exposure to its vapors may cause burning, tearing and
redness.
Skin: No harmful effects have been reported
Inhalation: Excessive concentrations of vapors or mists may cause irritation of the nose and throat. Persons with
impaired lung function or asthma like conditions may experience additional breathing difficulties.
Ingestion: Liquid is non-toxic
Potential Health Effects - Chronic
None
Carcinogenicity: NTP IARC Monographs OSHA Regulated
NO NO NO
4. First Aid Measures
Eye: Immediately flush with plenty of clean water for 15 minutes.
Skin: Remove contaminated clothing. Clean affected area(s) thoroughly with soap and water.
Inhalation: Remove to fresh air. If breathing is difficult, give oxygen.
Ingestion: Seek medical attention! Induce vomiting. If vomiting occurs spontaneously, keep head below hips to
prevent aspiration of liquid into the lungs.
SEEK MEDICAL ATTENTION IF SYMPTOMS PERSIST.
1
Date Prepared: 11/12/02
Supersedes: 08/01/01
Product Name: SpallGuard WB10%
5. Fire Fighting Measures
Flash Point (method used): >212掳F./100掳C.
Flammable Limits (% volume in air): Lower = N/AUpper = N/A
Auto Ignition Temperature: No data available
Extinguishing Media: Extinguish with water spray, dry chemical, CO2 or foam.
Hazard Combustion Products: none
Fire Fighting Instructions: Although there is no flash point, the product may form with air explosive vapor/air mixtures
when storage times of 6 months are exceeded.
6. Accidental Release Measures
Spill: Absorb with inert material, then place in chemical waste container for later disposal.
7. Handling and Storage
Handling: Avoid inhalation of vapors and personal contact with product. Use with adequate ventilation.
Storage: Store containers tightly closed with adequate ventilation in a cool, dry area.
8. Exposure Controls / Personal Protection
Exposure Controls: Not applicable
Personal Protection: Safety glasses and rubber gloves. A source of clean, potable water in work area should be
available for flushing eyes or skin.
9. Physical and Chemical Properties
Appearance: White liquid of low viscosity
Odor: Odorless
Boiling Point: 212掳F./100掳C
Melting Point: Not applicable
Vapor Pressure (mm/Hg): Not available
Vapor Density (Air = 1): >1
Solubility in Water: Negligible (<5%)
Specific Gravity (H20 = 1): 0.97
Evaporation Rate (n-Butyl Acetate = 1): Not available
pH: 8.5
10. Stability and Reactivity
Chemical Stability: Stable
Conditions to Avoid: None
Incompatibility (materials to avoid): None known
Hazardous Decomposition or By-products: After a long time, small amounts of ethanol may be formed
Hazardous Polymerization: Will not occur
2
Date Prepared: 11/12/02
Supersedes: 08/01/01
Product Name: SpallGuard WB10%
11. Toxicological Information
Components Oral LD50 Dermal LD50 Inhalation LC50
(rat) (rabbit) (rat)
Not applicable - - -
12. Ecological Information
No data available
13. Disposal Considerations
Dispose of in accordance with all federal, state, and local regulations. If uncertain of local requirements, contact
the proper environmental authorities for information on waste disposal in your area.
Not listed under RCRA 40 CFR 261 as hazardous.
14. Transportation Information
For U S National Shipments: Non-regulated
Shipping Description: Waterproofing compound, non-hazardous
Emergency Response Guide Number: N/A
Hazard Class: Non-regulated
15. Regulatory Information
OSHA: This material is non-hazardous by definition of Hazardous Communications Standard (29 CFR 1910.1200)
CERCLA Reportable Quantity: Not applicable
SARA Title III:
Section 311/312 hazard categories: N/A
Section 313 reportable ingredients:
Components CAS # Maximum %
None
16. Other Information
MSDS Status: Revised entire
Industrial Abbreviation Legend on page 4 of this MSDS.
3
Date Prepared: 11/12/02
Supersedes: 08/01/01
Product Name: SpallGuard WB10%
Industrial Abbreviation Legend
mg/m3
ACGIH American Conference of Governmental Industrial milligrams per cubic meter
NIOSH National Institute for Occupational Safety and Health
Hygienists
NTP National Toxicology Program
CAA Clean Air Act (EPA)
CERCLA Comprehensive Environmental Response, OSHA Occupational Safety and Health Administration
PEL Permissible Exposure Limit
Compensation & Liability Act of 1980 (Superfund) (EPA)
ppm parts per million
CNS Central Nervous System
CWA Clean Water Act (EPA) RCRA Resource Conservation and Recovery Act (EPA)
SARA EPA鈥檚 Superfund Amendment and Reauthorization
DOT Department of Transportation
Act (EPA)
EPA Environmental Protection Agency
g/kg grams per kilogram STEL Short-Term Exposure Limit, ACGIH terminology
TLV Threshold Limit Value
IARC Internal Agency for Research on Cancer
TWA Time-Weighted Average
LC50 Lethal Concentration in which 50% of the test animals are
expected to die
LD50 Lethal Dose in which 50% of the test animals are
expected to die
THIS PRODUCT IS FORMULATED AND LABELED FOR
INDUSTRIAL AND COMMERCIAL APPLICATION ONLY
The information contained herein is given in good faith and based on data considered accurate. However, no warranty is
expressed or implied regarding the accuracy of these data or the results to be obtained from the use thereof. ChemMasters
assumes no responsibility for personal injury or property damage to vendees, users or third parties caused by the material.
Such vendees or users assume all risks associated with the use of the material.
4
This is the last page of this MSDS.
|