Date Prepared: 11/13/02
ChemMasters
Supersedes: 08/01/01
Product Name: Textured II
Material Safety Data Sheet
1. Chemical Product and Company Information
Product Name: Textured II
Product Description: Textured II is a heavy bodied, acrylic emulsion, decorative, textured coating.
ChemMasters In Case of Emergency Contact:
300 Edwards Street CHEMTREC 800/424-9300
Madison, Ohio 44057
440-428-2105
2. Composition / Information on Ingredients
Components CAS # Exposure Limits % by Wt
OSHA(PEL/TWA) ACGIH (TLV/TWA) OTHER
10 mg/m3(%SiO2+2) 0.1 mg/m3 (resp)
Silica, Quartz 14808-60-7 鈥? 30-35
Water 7732-18-5 NE NE --- 20-25
Titanium Dioxide 13463-67-7 NE NE --- 10-15
Acrylic Polymer Trade Secret NE NE --- 9-10
Tremolite 14567-73-8 NE NE --- 6-8
Talc 14807-96-6 NE NE --- 3-7
Ethylene Glycol 107-21-1 鈥? 50 ppm (ceiling) --- 2
3. Hazards Identification
CAUTION
May Cause Eye Irritation
Potential Health Hazards - Acute
Eye: Direct contact may cause irritation.
Skin: Prolonged or repeated exposure may cause slight irritation.
Inhalation: Exposure to mist may cause headache, nausea and/or other symptoms of upper respiratory tract irritation.
Ingestion: Unlikely in hazardous amounts. Ingestion of very large amounts may damage the central nervous system,
gastrointestinal system and/or kidneys.
Potential Health Effects - Chronic:
Animal test results suggest Ethylene Glycol may cause liver, kidney and birth defects. However, there is no available
information to suggest Ethylene Glycol has caused birth defects in humans.
Carcinogenicity: NTP IARC Monographs OSHA Regulated
NO NO NO
4. First Aid Measures
Eye: Immediately flush with plenty of water for 15 minutes.
Skin: Wash with soap and water.
Inhalation: Move victim to fresh air
Ingestion: If swallowed, give victim plenty of water. Consult a physician.
SEEK MEDICAL ATTENTION IF SYMPTOMS PERSIST.
1
Date Prepared: 11/13/02
Supersedes: 08/01/01
Product Name: Textured II
5. Fire Fighting Measures
Flash Point (method used): Not applicable
Flammable Limits (% volume in air): Lower = Not applicable Upper =Not applicable
Auto Ignition Temperature: Not applicable
Extinguishing Media: Media appropriate for surrounding fire.
Hazard Combustion Products: Thermal decomposition may yield acrylic monomers, oxidizing agents, hypochlorites
Fire Fighting Instructions: Wear positive pressure, self-contained breathing apparatus.
6. Accidental Release Measures
Spill: Contain spilled material by diking. Absorb with inert material, then place in chemical waste container for later
disposal. Keep spills out of municipal sewers and open bodies of water.
7. Handling and Storage
Handling: Always use good industrial hygiene practices and safety guidelines.
Storage: Store material in its original container. Keep containers tightly closed when not in use. Protect from freezing.
8. Exposure Controls / Personal Protection
Exposure Controls: None required
Personal Protection: Safety glasses should be worn to minimize contact with this material. A source of clean water
should be available in work area for flushing eyes and skin.
9. Physical and Chemical Properties
Appearance: Gritty paint like colored liquid
Odor: Acrylic odor
Boiling Point: 212oF
Melting Point: Not applicable
Vapor Pressure (mm/Hg): 17 @20oC
Vapor Density (Air = 1): <1.0
Solubility in Water: 100%
Specific Gravity (H20 = 1): 1.65-1.76
Evaporation Rate (n-Butyl Acetate = 1): <1.0
10. Stability and Reactivity
Chemical Stability: Stable
Conditions to Avoid: Freezing and high temperatures
Incompatibility (materials to avoid): Strong acids, oxidizing agents, hypochlorites
Hazardous Decomposition or By-products: May yield acrylic monomers
Hazardous Polymerization: Will not occur
11. Toxicological Information
Components Oral LD50 Dermal LD50 Inhalation LC50
(rat) (rabbit) (rat)
Not applicable 鈥? 鈥? 鈥?
2
Date Prepared: 11/13/02
Supersedes: 08/01/01
Product Name: Textured II
12. Ecological Information
No data available.
13. Disposal Considerations
Dispose of in accordance with all federal, state, and local regulations. If uncertain of local requirements, contact
the proper environmental authorities for disposal.
This material does not meet RCRA鈥檚 characteristic definition of ignitability, corrosivity, or reactivity, and is not listed
in 40 CFR 261.33. The toxicity characteristic (TC), however has not been evaluated by the Toxicity Characteristic
Leaching procedure (TCLP).
14. Transportation Information
For U S National Shipments:
Shipping Description: Non-Regulated Material
Emergency Response Guide Number: Not applicable
Hazard Class: Not applicable
15. Regulatory Information
OSHA: This material is non-hazardous under the OSHA Hazard Communication Standard.
CERCLA Reportable Quantity: Not applicable
SARA Title III:
Section 311/312 hazard categories: Not applicable
Section 313 reportable ingredients:
Components CAS # Maximum %
Ethylene Glycol 107-21-1 2%
16. Other Information
MSDS Status: Revised entire
Industrial Abbreviation Legend on page 4 of this MSDS.
3
Date Prepared: 11/13/02
Supersedes: 08/01/01
Product Name: Textured II
Industrial Abbreviation Legend
mg/m3
ACGIH American Conference of Governmental Industrial milligrams per cubic meter
NIOSH National Institute for Occupational Safety and Health
Hygienists
NTP National Toxicology Program
CAA Clean Air Act (EPA)
CERCLA Comprehensive Environmental Response, OSHA Occupational Safety and Health Administration
PEL Permissible Exposure Limit
Compensation & Liability Act of 1980 (Superfund) (EPA)
ppm parts per million
CNS Central Nervous System
CWA Clean Water Act (EPA) RCRA Resource Conservation and Recovery Act (EPA)
SARA EPA鈥檚 Superfund Amendment and Reauthorization
DOT Department of Transportation
Act (EPA)
EPA Environmental Protection Agency
g/kg grams per kilogram STEL Short-Term Exposure Limit, ACGIH terminology
TLV Threshold Limit Value
IARC Internal Agency for Research on Cancer
TWA Time-Weighted Average
LC50 Lethal Concentration in which 50% of the test animals are
expected to die
LD50 Lethal Dose in which 50% of the test animals are
expected to die
THIS PRODUCT IS FORMULATED AND LABELED FOR
INDUSTRIAL AND COMMERCIAL APPLICATION ONLY
The information contained herein is given in good faith and based on data considered accurate. However, no
warranty is expressed or implied regarding the accuracy of these data or the results to be obtained from the use
thereof. The Spray-Cure Company assumes no responsibility for personal injury or property damage to vend-
ees, users or third parties caused by the material. Such vendees or users assume all risks associated with the
4
use of the material.
This is the last page of this MSDS.
|