**** SECTION 2 - COMPOSITION, INFORMATION ON INGREDIENTS ****
+----------------+--------------------------------------+----------+-----------+
| CAS# | Chemical Name | % | EINECS# |
|----------------|--------------------------------------|----------|-----------|
| 3886-69-9 |r-(+)-1-Phenylethylamine | 98.0 | 223-423-4 |
+----------------+--------------------------------------+----------+-----------+
Hazard Symbols: C
Risk Phrases: 34
**** SECTION 3 - HAZARDS IDENTIFICATION ****
EMERGENCY OVERVIEW
Causes burns.Corrosive.Combustible liquid.
Potential Health Effects
Eye:
Causes severe eye burns.
Skin:
Causes severe burns.
Ingestion:
May cause irritation of the digestive tract.
Inhalation:
Causes respiratory tract irritation.
Chronic:
No information found.
**** SECTION 4 - FIRST AID MEASURES ****
Eyes:
Immediately flush eyes with plenty of water for at least 15 minutes,
occasionally lifting the upper and lower eyelids. Get medical aid
immediately. Do NOT allow victim to rub eyes or keep eyes closed.
Skin:
Get medical aid immediately. Flush skin with plenty of water for at
least 15 minutes while removing contaminated clothing and shoes.
Discard contaminated clothing in a manner which limits further
exposure.
Ingestion:
If victim is conscious and alert, give 2-4 cupfuls of milk or water.
Never give anything by mouth to an unconscious person. Get medical
aid immediately.
Inhalation:
Remove from exposure and move to fresh air immediately. If not
breathing, give artificial respiration. If breathing is difficult,
give oxygen. Get medical aid.
Notes to Physician:
**** SECTION 5 - FIRE FIGHTING MEASURES ****
General Information:
As in any fire, wear a self-contained breathing apparatus in
pressure-demand, MSHA/NIOSH (approved or equivalent), and full
protective gear. Will burn if involved in a fire. Use water spray to
keep fire-exposed containers cool. Combustible liquid. Containers may
explode when heated.
Extinguishing Media:
Use water spray to cool fire-exposed containers. Cool containers
with flooding quantities of water until well after fire is out. Use
water spray, dry chemical, carbon dioxide, or alcohol-resistant foam.
**** SECTION 6 - ACCIDENTAL RELEASE MEASURES ****
General Information: Use proper personal protective equipment as indicated
in Section 8.
Spills/Leaks:
Absorb spill with inert material (e.g. vermiculite, sand or earth),
then place in suitable container. Remove all sources of ignition.
Provide ventilation.
**** SECTION 7 - HANDLING and STORAGE ****
Handling:
Wash thoroughly after handling. Use with adequate ventilation. Do
not get in eyes, on skin, or on clothing. Empty containers retain
product residue, (liquid and/or vapor), and can be dangerous. Take
precautionary measures against static discharges. Keep container
tightly closed. Keep away from heat, sparks and flame. Avoid
ingestion and inhalation. Do not pressurize, cut, weld, braze,
solder, drill, grind, or expose empty containers to heat, sparks or
open flames.
Storage:
Keep away from heat, sparks, and flame. Keep away from sources of
ignition. Store in a tightly closed container. Store in a cool, dry,
well-ventilated area away from incompatible substances. Corrosives
area.
**** SECTION 8 - EXPOSURE CONTROLS, PERSONAL PROTECTION ****
Engineering Controls:
Use adequate ventilation to keep airborne concentrations low.
Exposure Limits
CAS# 3886-69-9:
Personal Protective Equipment
Eyes:
Wear appropriate protective eyeglasses or chemical
safety goggles as described by OSHA's eye and face
protection regulations in 29 CFR 1910.133 or European
Standard EN166.
Skin:
Wear appropriate protective gloves to prevent skin
exposure.
Clothing:
Wear appropriate protective clothing to prevent skin
exposure.
Respirators:
Follow the OSHA respirator regulations found in 29
CFR 1910.134 or European Standard EN 149. Use a
NIOSH/MSHA or European Standard EN 149 approved
respirator if exposure limits are exceeded or if
irritation or other symptoms are experienced.
**** SECTION 9 - PHYSICAL AND CHEMICAL PROPERTIES ****
Physical State: Liquid
Color: clear, colorless
Odor: None reported
pH: 10.7
Vapor Pressure: 0.5 mmHg @ 20 C
Viscosity: Not available.
Boiling Point: 180.0 - 181.0 C
Freezing/Melting Point: -65 deg C
Autoignition Temperature: Not available.
Flash Point: 79 deg C ( 174.20 deg F)
Explosion Limits, lower: Not available.
Explosion Limits, upper: Not available.
Decomposition Temperature:
Solubility in water: Soluble.
Specific Gravity/Density: .9400
Molecular Formula: C8H11N
Molecular Weight: 121.0837
**** SECTION 10 - STABILITY AND REACTIVITY ****
Chemical Stability:
Stable under normal temperatures and pressures.
Conditions to Avoid:
Incompatible materials, ignition sources.
Incompatibilities with Other Materials:
Acids, acid chlorides, acid anhydrides, carbon dioxide, strong
oxidizing agents.
Hazardous Decomposition Products:
Nitrogen oxides, carbon monoxide, carbon dioxide.
Hazardous Polymerization: Has not been reported.
**** SECTION 11 - TOXICOLOGICAL INFORMATION ****
RTECS#:
CAS# 3886-69-9 unlisted.
LD50/LC50:
Not available.
Carcinogenicity:
r-(+)-1-Phenylethylamine -
Not listed by ACGIH, IARC, or NTP.
**** SECTION 12 - ECOLOGICAL INFORMATION ****
**** SECTION 13 - DISPOSAL CONSIDERATIONS ****
Dispose of in a manner consistent with federal, state, and local regulations.
**** SECTION 14 - TRANSPORT INFORMATION ****
IATA
Shipping Name: AMINES, LIQUID, CORROSIVE, N.O.S.*
Hazard Class: 8
UN Number: 2735
Packing Group: III
IMO
Shipping Name: AMINES, LIQUID, CORROSIVE, N.O.S.
Hazard Class: 8
UN Number: 2735
Packing Group: III
RID/ADR
Shipping Name: AMINES, LIQUID, CORROSIVE, N.O.S.
Hazard Class: 8
UN Number: 2735
Packing group: III
**** SECTION 15 - REGULATORY INFORMATION ****
European/International Regulations
European Labeling in Accordance with EC Directives
Hazard Symbols: C
Risk Phrases:
R 34 Causes burns.
Safety Phrases:
S 26 In case of contact with eyes, rinse immediately
with plenty of water and seek medical advice.
S 28A After contact with skin, wash immediately with
plenty of water.
S 36/37/39 Wear suitable protective clothing, gloves
and eye/face protection.
S 45 In case of accident or if you feel unwell, seek
medical advice immediately (show the label where
possible).
WGK (Water Danger/Protection)
CAS# 3886-69-9: No information available.
Canada
CAS# 3886-69-9 is listed on Canada's NDSL List.
CAS# 3886-69-9 is not listed on Canada's Ingredient Disclosure List.
US FEDERAL
TSCA
CAS# 3886-69-9 is listed on the TSCA inventory.
**** SECTION 16 - ADDITIONAL INFORMATION ****
MSDS Creation Date: 7/13/1998 Revision #2 Date: 3/18/2003
The information above is believed to be accurate and represents the best
information currently available to us. However, we make no warranty of
merchantability or any other warranty, express or implied, with respect to
such information, and we assume no liability resulting from its use. Users
should make their own investigations to determine the suitability of the
information for their particular purposes. In no way shall the company be
liable for any claims, losses, or damages of any third party or for lost
profits or any special, indirect, incidental, consequential or exemplary
damages, howsoever arising, even if the company has been advised of
the possibility of such damages.
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
|
|
|
| ALL MSDS PAGES IN THIS GROUP
| | NAME | CAS |
|
1-Methyl-2-pyrrolidinone, 99+%, spectrophotometric grade
| 872-50-4 |
|
1-Methyl-2-pyrrolidinone, 99%
| 872-50-4 |
|
Sodium Iodide, 99.999%
| 7681-82-5 |
|
Guanidine Hydrochloride, 99% (Contains 0.2-0.4% SiO2 as Anti-Caking
| 50-01-1 |
|
Guanidine Hydrochloride, 98%
| 50-01-1 |
|
Phenoxy resin, average m.w. 70000
| 26402-79-9 |
|
N,N-Dimethylbenzylamine, 98%
| 103-83-3 |
|
N,N-Dimethylformamide, 99%
| 68-12-2 |
|
2-Methylbutane, 99+%
| 78-78-4 |
|
2-Methylbutane, 99+%, spectrophotometric grade
| 78-78-4 |
|
N,N-Dimethylformamide, P.A.
| 68-12-2 |
|
Polyethyleneglycol 300 Monononylether (Fractionated, Fraction 5)
| 39587-22-9 |
|
Polyethyleneglycol 300 Monooctylether
| 27252-75-1 |
|
Polyethyleneglycol 300 Monooctylether (Fractionated, Fraction 2)
| 27252-75-1 |
|
6-Ketocholestanol, 99%
| 1175-06-0 |
|
Polyethyleneglycol 300 monooctylether (Fractionated, Fraction 5)
| 27252-75-1 |
|
Dicyandiamide, 99.5%
| 461-58-5 |
|
Nitrazine Yellow, Indicator Grade
| 5423-07-4 |
|
Polyethyleneglycol 400 Monooctylether
| 27252-75-1 |
|
Polyethyleneglycol 600 Monooctylether
| 27252-75-1 |
|
N,N-Dimethylformamide for HPLC
| 68-12-2 |
|
N,N-Dimethylformamide, Reagent ACS
| 68-12-2 |
|
N,N-Dimethylformamide, Nonaqueous Titration Grade, 99+% (GC)
| 68-12-2 |
|
2-Isonitrosoacetophenone, 99%
| 532-54-7 |
|
N,N-Dimethylformamide, Reagent ACS, Spectro Grade, 99.8% (GC)
| 68-12-2 |
|
N,N-Dimethylformamide, 99+% Spectrophotometric Grade
| 68-12-2 |
|
R(+)-alpha-methylbenzyl isocyanate, 95%
| 33375-06-3 |
|
s-(-)-1-Phenylethylamine, 98% (uv-vis)
| 2627-86-3 |
|
r-(+)-1-Phenylethylamine, 98% (uv-vis)
| 3886-69-9 |
|
1,4-Dichlorobutane, 99+%
| 110-56-5 |
|
(-)-Taddol, 98%, (99% e.e.)
| 93379-48-7 |
|
3-Methyltetrahydrofuran, 99%
| 13423-15-9 |
|
Merrifield's peptide resin, 2% cross- linked, 2-2.5 meq cl/g, 200-400
| 9036-15-1 |
|
Cyclohexanone, 99.8%
| 108-94-1 |
|
1-Bromo-3-chloropropane, p.a.
| 109-70-6 |
|
2-Octenoic acid, 90-95% trans
| 1871-67-6 |
|
Fluorene (Techn), 90% (UV-Vis)
| 86-73-7 |
|
Chrysene, 98%
| 218-01-9 |
|
Aluminum chloride hexahydrate, 99%
| 7784-13-6 |
|
Carmine certified alum lake
| 1390-65-4 |
|
Carmine, high purity biological stain, (alum lake of carminic
| 1390-65-4 |
|
Trichlorovinylsilane, 96%
| 75-94-5 |
|
p-Xylene, 99%
| 106-42-3 |
|
p-Xylene, scintillation grade, 99%
| 106-42-3 |
|
Cyclooctanemethanol, 97%
| 3637-63-6 |
|
m-Xylene, spectro grade
| 108-38-3 |
|
2,3,3-Trichlorotetrahydrofuran, 98%
| 0-00-1 |
|
4-Chloro-1-(2,5-Dimethylphenyl)-1-Butanone
| 71526-84-6 |
|
4-Chloro-1-(2,4-Dimethylphenyl)-1-Butanone
| 74298-65-0 |
|
Fast Green FCF, High Purity Biological Stain
| 2353-45-9 |
|
|