MATERIAL SAFETY DATA SHEET
SECTION I: MANUFACTURER & MATERIAL IDENTIFICATION
Manufacturer Kramer Industries, Inc. Emergency Phone 732-650-9599
140 Ethel Road West
Suite U
Piscataway, NJ 08854-5951
Acrylic Plastic Abrasive
Product
CAS Number None
Date Prepared Revised 1/07
SECTION II: HAZARDOUS INGREDIENTS/IDENTITY INFORMATION
HAZARDOUS COMPONENTS CAS # PEL (ppm) TLV (ppm)
No Hazardous Components None
INGREDIENTS Exposure Limit
Acrylic Polymer ACGIH None
OSHA None
SECTION III: PHYSICAL/CHEMICAL CHARACTERISTICS
Evaporation Rate Solid Vapor Density N/A
Solubility in Water Insoluble Percent Volatile N/A
Approximate Boiling Range N/A Density 1.19
SECTION IV: FIRE AND EXPLOSION HAZARD DATA
Flash Point, ASTM D-1929 Estimated Flash Approx. 391掳C
Flammable Limits N/A
Extinguishing Media Foam, Carbon Dioxide, Water, Dry Chemical
Special Procedures Full protective equipment
Unusual Fire & Explosion Hazards None known
MSDS for Acrylic Plastic Abrasive cont.
SECTION V: REACTIVITY DATA
Stability Stable
Conditions to Avoid Sources of ignition and temperatures above 570掳F or 370掳C
Incompatibility N/A
Hazardous Decomposition Under fire conditions, hazardous decomposition products will include: CO, CO2 and
smoke. Temperatures above 370掳C can cause methyl methacrylate monomer
(MMA) to be released. See section 8.
Vapor may cause irritation to the eyes, nose and throat. May cause central nervous
system effects such as dizziness, headache, nausea and loss of consciousness.
Under some circumstances, mutagenic changes have been observed with MMA.
The meaning and significance of these results is not understood. At 1000 ppm, MMA
is weakly embryotoxic with rats.
Exposure Limits Cas Number Vapor Pressure
OSHA & ACGIH
MMA 100ppm 80-62-6 29 mm (20掳C)
Hazardous Polymerization Will not occur
SECTION VI: HEALTH HAZARD DATA
Symptoms/Effects of Overexposure and First Aid Ingestion: Ingestion of small quantities of this material under
normal circumstances would not cause harmful effect.
Inhalation: Gross overexposure to nuisance particles, regardless of how generated, may cause irritation of the
respiratory tract. If irritation develops, remove to fresh air. If breathing difficulty persists, consult a physician.
Skin or Eye Contact: Nuisance particles may cause irritation. In case of eye contact, flush immediately with
large amounts of water. For skin, wash with soap and water. If irritation persists, consult a physician.
SECTION VII: PRECAUTIONS FOR SAFE HANDLING AND USE
Spill No special procedures required.
Waste Disposal Sanitary landfill, in accordance with Federal, State and Local Regulations.
Handling & Storage N/A
The information contained in this material safety data sheet is, to our best knowledge, true and accurate, but all recommendations or suggestions are made
without guarantee, since the conditions of use are beyond our control. It is the user's responsibility to determine the safety, toxicity and suitability for his own use
of the product described herein. KRAMER INDUSTRIES, INC. disclaims any liability incurred in connection with the use of these data or suggestions.
MSDS for Acrylic Plastic Abrasive cont.
SECTION VIII: CONTROL MEASURES
Respiratory Protection Do not breath dust. Wear a properly fitted dust respirator approved by NIOSH/MSHA
during application, unless air monitoring shows dust levels below 10 mg/m3.
Ventilation Provide sufficient ventilation in volume and pattern to keep airborne levels of methyl
methacrylate below 100 ppm and dust levels below 10 mg/m3.
Protective Gloves Leather gloves are recommended
Eye Protection Safety glasses with side shields
Other Equipment None required
Work/Hygiene Practices Observe standard industrial hygiene practices
Transportation: Not regulated
SECTION IX: REGULATORY STATUS
NTP Not listed
IARC Monographs Not listed
OSHA Regulated Not regulated
Notice From Kramer Industries, Inc.: The data in this material safety sheet relate only to specific material
designated herein and do not relate to use in combination with any other material or process.
The information contained in this material safety data sheet is, to our best knowledge, true and accurate, but all recommendations or suggestions are made
without guarantee, since the conditions of use are beyond our control. It is the user's responsibility to determine the safety, toxicity and suitability for his own use
of the product described herein. KRAMER INDUSTRIES, INC. disclaims any liability incurred in connection with the use of these data or suggestions.
|