Crystal Cote
Wood Floor Care
WF For Use On:
Sealed Wood Sealed Concrete
Sealed Cork Parquet Floors
Polyurethane
DESCRIPTION
A light colored, high quality oil modified urethane floor finish designed
for use on wood. Produces a non-yellowing, extremely durable, high
Wood Finish
gloss finish; ideal for gymnasiums. Easy to apply, it is compatible
over a wide variety of conventional solvent based and water-based
coatings (provided these coatings are cured, bonded and the floor is
properly prepared).
Manufacturer鈥檚 Recommendation: This coating is to be
applied without thinning.
VOC Content = 493 grams/liter
DIRECTIONS
ON NEW OR NEWLY PREPARED FLOORS: Use a good quality
polyurethane sealer; following label directions carefully. Allow to dry
thoroughly.
ON NEWLY SEALED FLOORS: Buff with a #120 abrasive screen.
Clean surface thoroughly with a tack rag and waterless cleaner and
allow to dry. Apply finish using a synthetic or lamb鈥檚 wool applicator,
pressure sprayer or gravity fed applicator. If more than one coat is
desired, allow 6 to 8 hours dry time between coats. No screening is
required if recoating is done within 24 hours. Allow 48 hours cure time
before allowing any foot traffic on floors.
NOTE: Best results are obtained with adequate ventilation and floor
temperature above 60掳F and below 95掳F. Avoid direct drafts on floor
while finishing.
CAUTION: Do not use on any resilient type flooring.
PRODUCT SPECIFICATIONS
Non-volatile solids: 42.0卤0.5% Removability: With conventional urethane
Gardner Color: (Typical)..................4 strippers
(Maximum)............12 Drying Properties: Set to touch - 1-2 hrs.
Odor: Solvent Recoat - 6-8 hrs.
Type: Oil modified urethane Dry hard - 48 hrs.
Solvent Systems: Mineral spirits Recoatability: Excellent (follow directions)
o
Flash Point: 106 F (TCC) Storage/Stability: 2 years
Viscosity: A-C, Gardner Freeze/Thaw Stability: Keep from freezing
Slip Resistance: Greater than 0.50 Weight per Gallon: 7.09 lbs./gal.
400-500 ft2 per gal.
Sward Hardness: Greater than 30 Coverage:
Chemical Resistance: Excellent VOC Content: 493 gms/liter
Misco Products Corporation 鈥? Reading, PA 鈥? (800) 548-4568 FAX (610) 926-1194
www.miscoprod.com
U42 MATERIAL SAFETY DATA SHEET N/A=Not Applicable
Prepared by: Regulatory Affairs Dept. Effective Date: 5/99 Revision: 10/99
(Prepared According to 29 CFR 1910.1200)
SECTION 1-PRODUCT IDENTIFICATION AND SUPPLIER INFORMATION
Manufacturer鈥檚 Name: Product Name: Crystal Cote Finish Supplier鈥檚 Name:
Misco Products Corporation Generic Name: Polyurethane Wood Finish
Manufacturer鈥檚 Address: Supplier鈥檚 Address:
Chemical Family: Solvent Urethane Blend
1048 Stinson Drive Reading, PA 19605 Formula: Proprietary
Manufacturer鈥檚 Phone #: (610) 926-4106 Supplier鈥檚 Phone #:
SECTION 2-INGREDIENT INFORMATION
CHEMICAL NAME CAS NO. WT. % PEL TWA-TLV STEL-TLV
Petroleum Distillates 8052-41-3 55 to 58 300 ppm 100 ppm N/A
Oil Modified Urethane Resin N/A 42 to 45
SECTION 3-PHYSICAL DATA SECTION 4-FIRE AND EXPLOSION HAZARD DATA
Flash Point (Method Used): 106 F. (TCC)
Boiling Point (掳F): 300 F. Initial Specific Gravity: .893
Upper Explosion Limit: 6.0 Lower Explosion Limit: 1.0
Vapor Pressure: <10mm Hg @ 68 F. Vapor Density (Air=1): >1
Extinguishing Media: Foam, CO2, dry chemical.
% Volatile: 45+ pH: N/A
Special Firefighting Procedures: Do Not Use Water.
Solubility in Water: Nil Evaporation Rate (Water=1): <1
Unusual Fire and Explosion Hazards: Drums heated by fire can explode.
Physical Description: Moderately viscous yellow liquid with characteristic odor.
VOC Content (Subpart D 搂59.406) : 493 g/l
SECTION 5-REACTIVITY DATA
Stability: Stable Hazardous Polymerization: May occur through oxidation, leading to exothermic
reaction. Heat generated by oxidation may lead to spontaneous combustion of materials
such as rags, paper towels, etc., used for clean-up
Hazards Decomposition Products: Carbon monoxide possible if burned. Incompatibility (Materials to Avoid): Strong oxidizers.
SECTION 6-STORAGE AND HANDLING INFORMATION
Combustible liquid. Avoid contact with heat, spark or open flame. Keep out of reach of children. For use by trained personnel only. Keep unauthorized personnel away when
applying to floor. Keep container closed during storage. For institutional and industrial use only. Avoid contact with eyes, skin and clothing. Wear rubber gloves when handling.
Wear protective boots when applying to floors. Avoid breathing of vapors. Use in well-ventilated area.
SECTION 7-HEALTH HAZARDS AND FIRST AID SECTION 8-SPECIAL PROTECTION INFORMATION
Effects of Overexposure: Respiratory Protection: NIOSH approved hydrocarbon cartridge or self-contained
apparatus when used in enclosed areas.
Skin: Prolonged or repeated contact may cause irritation, defatting, or dermatitis.
Ventilation Requirements: Provide local exhaust to keep TLV of Section 2 in-
Eyes: Eye irritant. May cause redness, swelling, or blurred vision.
gredients below acceptable limit. Open doors and windows when handling and during
Inhalation: May be irritating to the nose, throat, and lungs. Prolonged breathing can
drying period.
cause headache, nausea, dizziness, weakness, and fatigue. Some reports have associated
Protective Gloves: Solvent proof rubber recommended.
repeated and prolonged occupational overexposure to solvents with permanent brain
and nervous system damage. Eye Protection: Safety glasses recommended.
Ingestion: Can cause irritation of the gastrointestinal tract, nausea, vomiting, and Other Protective Equipment: Eye wash station should be available nearby. Protective
diarrhea. Aspiration of material into the lungs can cause pneumonitis. clothing and footwear (rubber boots) when using on floors.
First Aid Procedures: SECTION 9-SPILL OR LEAK PROCEDURES
Skin: Remove contaminated clothing. Wash with soap and water. Seek medical Steps to be taken in Case Material is Released or Spilled: Shut off all ignition
attention if irritation persists. sources. Ventilate area well. Floors will become slippery. Avoid walking in product.
Keep unessential personnel away. Mop up or otherwise absorb and hold disposal.
Eyes: Flush with large quantities of water, holding eyelids open. Seek medical
Avoid discharge to sewer or open waterways.
attention.
Waste Disposal Method: Any method in accordance with local, state and federal laws.
Inhalation: Get to fresh air. If breathing is difficult, give oxygen. Seek medical
Best method is to recycle or reuse for intended purpose. If discarded, this material and
attention if symptoms persist.
containers should be treated as hazardous waste based on the characteristic of
Ingestion: Do not induce vomiting. Seek medical attention immediately.
ignitability as defined under federal RCRA regulations (40 CFR 261). Materials used to
absorb product should be soaked in water-filled containers or rinsed with water prior to
discarding in trash receptacles. Do not dispose of into storm drain, stream, river or to
ground. Rinse container thoroughly before discarding in trash.
SECTION 10-REGULATORY INFORMATION
HMIS Hazardous Materials
SARA Title III - Section 311/312 -Hazard Categories: Shipping Information:
Yes - Fire Hazard FOR CONTAINERS > 1 Gallon : Cleaning Compound Identification System
No - Sudden Release of Pressure Hazard Health 2
No - Reactivity Hazard FOR 1 GALLON CONTAINERS : Cleaning Compound Flammability 2
Yes - Immediate (acute) Health Hazard Reactivity 0
No - Delayed (chronic) Health Hazard FOR CONTAINERS < 1 GALLON : Cleaning Compound Personal Protection B
FOR EMERGENCY MEDICAL OR TRANSPORT INFORMATION: CHEM-TEL, Inc. @ 800-255-3924 (24 hours, 7 days per week)
This product contains the following toxic chemical(s) subject to the reporting requirements of section 313 of the Emergency Planning and Community Right-To-Know Act of 1986
and of 40 CFR 372.
CAS# Chemical Name Percent by Weight
None
This product contains the following chemical(s) which have been established to be either a carcinogen or suspected carcinogen.
CAS# Chemical Name Percent by Weight
None
SECTION 11-OTHER INFORMATION
This company cannot anticipate all conditions of handling and use of this product. Therefore, this company accepts no responsibility for results obtained by the application of this
information, or the safety and suitability of our products either alone or in combination with other products. It is the responsibility of the user to provide a safe workplace, using
the health and safety information contained herein as a guide. This company will accept no liability for damages or loss incurred from the improper handling and use of this
product
|