Tnemec Company, Inc. For coatings, resins and related materials, approved by
Material Safety Data Sheet (MSDS) the U.S. Department of Labor as essentially similar to
123 West 23rd Avenue, Kansas City, MO 64116-3064
form OSHA-20, meets requirements of CFR 29 Part
Emergency Telephone: 800-535-5053 (INFOTRAC)
1910.1200, OSHA'S hazard communication standard.
Telephone: 816-474-3400 NPCA 1-84
11/01/2006 V626-NOPG SILICONE RUBBER DUR A PELL GS VOC Page 1 of 2
PREPARED DATE: Series: Product Class:
SECTION 2 - HAZARDOUS INGREDIENTS
VAPOR OCCUPATIONAL EXPOSURE LIMITS
PRESS. ACGIH OSHA
MMHG
INGREDIENTS CAS# % By Wt. TLV - TWA TLV - STEL TLV - C PEL -TWA PEL - STEL PEL - C
o
@ 68 F
BENZENE, 1-CHLORO-4-(TRIFLUOROMETHYL)- 98-56-6 86.75
** SARA Reportable Product
This product contains no reported carcinogens or suspected carcinogens.
SECTION 3 - HEALTH HAZARD INFORMATION
EMERGENCY OVERVIEW: POTENTIAL HEALTH EFFECTS: EYE: Moderate irritation. Redness, tearing, blurred vision. SKIN: Moderate irritation, drying of skin, defatting and possible dermatitis.
INHALATION - OVEREXPOSURE TO SOLVENT VAPORS OR SPRAY MIST: Nasal and respiratory irritation, anesthetic effects, dizziness, possible unconsciousness and asphyxiation, stupor, weakness,
fatigue, nausea, and headache. INHALATION - OVEREXPOSURE TO FREE PIGMENT DUST: INGESTION: Gastrointestinal irritation, nausea, vomiting, diarrhea, death, aspiration into the lungs which can
be fatal. CHRONIC EFFECTS: NOTICE: Reports have associated repeated and prolonged occupational overexposure to solvents with permanent brain and nervous system damage. Intentional misuse by
deliberately concentrating and inhaling the vapors may be harmful or fatal. TARGET ORGANS: Can cause eye irritation. Can cause skin irritation. Can cause respiratory tract irritation. Can cause gastrointestinal
tract irritation. Can cause liver damage. Can cause kidney damage. Can cause nervous system effects. OTHER: This product when mixed with other components acquires the hazards of all components.
PRIMARY ROUTES OF ENTRY: Dermal and Inhalation. PROPOSITION 65: Pigments and/or other raw materials present in this product contain trace amounts of a chemical or chemicals known to the State of
California to cause cancer, birth defects or other reproductive harm.
SECTION 4 - FIRST AID MEASURES
EYE CONTACT: Flush immediately with large amounts of clean water under low pressure for at least 15 minutes. Consult a physician. SKIN CONTACT: Wash affected area with soap and water. Remove
contaminated clothing. Dispose of or launder accordingly. Consult a physician if skin irritation persists. INHALATION: Remove affected individual to fresh air. Treat symptomatically. If breathing is difficult,
administer oxygen. If breathing has stopped give artificial respiration. Consult a physician. INGESTION: Drink 1 or 2 glasses of water to dilute. Do not induce vomiting. Consult a physician or poison control
center IMMEDIATELY. Treat symptomatically. NOTE TO PHYSICIAN:
SECTION 5 - FIRE AND EXPLOSION HAZARD DATA
FLAMMABILITY CLASSIFICATION FLASHPOINT EXPLOSION LEVEL LOW EXPLOSION LEVEL HIGH FLAMMABILITY LIMITS LOWER FLAMMABILITY LIMITS HIGHER
103.0 掳F -N/A -N/A -N/A -N/A
EXTINGUISHING MEDIA: Foam, carbon dioxide, and dry chemical. FIRE-FIGHTING PROCEDURES AND EQUIPMENTS: Keep away from heat, open flames, sparks, and areas where static charge may be
generated. Do not apply to hot surfaces due to possible fire and explosion risk. For closed containers, pressure build-up and possible explosion might occur due to extreme heat exposure. Solvent vapors are
heavier than air and may travel considerable distance to a source of ignition and flash back. Water may be used to cool unruptured containers. Wear self-contain- ed breathing apparatus with a full facepiece
operated in pressure- demand or other positive pressure mode to prevent inhalation of hazardous decomposition products. Use appropriate extinguishing media to control fire. Water may cause violent frothing if
sprayed directly into containers of burning liquid.
SECTION 6 - SPILL OR LEAK PROCEDURES
CLEAN-UP: Remove all sources of ignition. Spills may be collected with inert, absorbent material for proper disposal. Use non-sparking tools, protective gloves, goggles and clothing, adequate ventilation, avoid
the breathing of vapors and use respiratory protective devices. Transfer absorbent material to suitable containers for proper disposal.
SECTION 7 - SPECIAL PRECAUTIONS
HANDLING AND STORAGE: Store in dry area. Keep closures tight and upright to prevent leakage. Do not store in high temperature areas or near fire or open flame. Refer to product data sheet for
recommended storage temperatures. SPECIAL COMMENTS: Prevent prolonged breathing of airborne contaminants such as vapor, spray mists, or dusts. Prevent contact with skin and eyes. Do not take
internally. Keep out of reach of children. Do not reuse or alter containers without proper industrial cleaning. Do not weld or flame cut empty, uncleaned containers due to potential fire and explosion hazard.
Consult product data sheet for proper application instructions.
11/01/2006 V626-NOPG SILICONE RUBBER DUR A PELL GS VOC Page 2 of 2
PREPARED DATE: Series: Product Class:
SECTION 8 - SAFE HANDLING AND USE INFORMATION
HYGIENIC PRACTICES: Wash hands and other contaminated skin areas with warm soap and water before eating. EYE PROTECTION: Use chemical resistant splash type goggles. RESPIRATORY
PROTECTION: Respiratory protective devices must be used when engineering and administration controls are not adequate to maintain Threshold Limit Values (TLV) and Permissible Exposure Limits (PEL) of
airborne contaminants below the listed values for those hazardous ingredients identified in Section II of this MSDS. Observe OSHA regulations for respirator use (CFR 29, 1910.134) whenever a respirator is
used. Particulate, chemical cartridge, air purifying half-mask respirators can be used within certain limitations; consult the respirator manufacturer for specific uses and limitations. Where airborne contaminant
concentrations are unknown, the use of a NIOSH/MSHA approved fresh-air supplied respirator is mandatory. OTHER PROTECTION: Use Chemical resistant gloves. Use chemical resistant coveralls or apron to
protect against skin and clothing contamination. Use protective cream where skin contact is likely. VENTILATION: Sufficient ventilation, in volume and pattern, should be provided through both local and general
exhaust to keep the air contaminant concentration below current applicable OSHA Permissible Exposure Limits (PEL) and ACGIH's Threshold Limit Values (TLV). Appropriate ventilation should be employed to
remove hazardous decomposition products formed during welding or flame cutting operations of surfaces coated with this product. Heavier than air solvent vapors should be removed from lower levels of work
area due to potential explosion hazard and all ignition sources (non-explosion proof equipment) should be eliminated if flammable mixtures will be encountered.
SECTION 9 - PHYSICAL AND CHEMICAL PROPERTIES
LOWER HIGHER FORMULA WEIGHT VOC IN LBS PER EVAPORATION %VOLATILE BY
VAPOR PRESSURE VAPOR DENSITY
BOILING RANGE BOILING RANGE BY VOLUME GALLON RATE WEIGHT
-N/A -N/A 282.0 掳F -N/A 掳F 10.6801 LB/GL .805 .000 (Ether = 1) 1.990
SECTION 10 - STABILITY AND REACTIVITY
INCOMPATIBILITIES: Strong oxidizing agents. DECOMPOSITION: Hydrogen chloride. Hydrogen Fluoride and Organic Halides. CONDITIONS TO AVOID: Heat, sparks, open flames. POLYMERIZATION: Will
not occur. STABILITY: Stable.
SECTION 13 - DISPOSAL CONSIDERATIONS
WASTE DISPOSAL: Dispose of in accordance with Federal, state, and local regulations regarding pollution.
SECTION 16 - HMIS INFORMATION
Health: 1 Flammability: 2 Reactivity: 1
This is a condensed MSDS, providing safety and health information pertinent to the complete product series. Physical constants such as Wt./Gal., VOC content and chemical constituents will vary with color. Safety and health
information may also vary with color. Certain colors may contain Carbon Black and Crystalline Silica, which have been identified as reported or suspected carcinogens. Prolonged inhalation of respirable dusts containing Crystalline
Silica may result in the development of a lung disease known as silicosis. For a complete, color-specific MSDS, please contact your local Tnemec representative listed at www.tnemec.com.
For specific information regarding occupational safety and health standards, please refer to the Code of Federal Regulations, Title 29, Part 1910. To the best of our knowledge, the information contained herein is accurate. However,
neither the Tnemec Company or any of its subsidiaries assume any liability whatsoever for the accuracy of completeness of the information contained herein. Final determination of suitability of any material is the sole responsibility
of the user. All materials may present unknown health hazards and should be used with caution. Although certain hazards are described herein, we cannot guarantee that these are the only hazards which exist.
|