ABN 65 007 171 333
MATERIAL SAFETY DATA SHEET
1. Identification of Material and Supplier
Leakmaster
Product Name
None
Other Names
Recommended Use Absorbs water and expands when in contact . A Polyurethane-based
sealing compound that cures by reaction with air humidity.
Supplier Name Corkjoint (Aust )Pty Ltd
Address 29 Capella Crescent, Moorabbin East, Vic. 3189
www.corkjoint.com.au
Web Address
03 9532 0822
Telephone 03 9532 61 22
Facsimile
Emergency Telephone 03 9532 0822
2. Hazards Identification
Hazard Classified as non-hazardous according to the criteria of the NOHSC and the ADG Code. Not scheduled as a
poison in the SUSDP. Non-irritant, non-sensitising, non-corrosive, non-explosive, non-toxic in the form sold.
Classification
None allocated or required.
Risk Phrases
Safety Phrases None allocated or required.
3. Composition/Information on Ingredients
Proportion
Chemical Identity CAS No
100 %
All components are determined to be non-hazardous or n.d.
below cut-off values
Page 1 of 4
Reference No 0002 Version 1.0 Issue Date 8/03/2004
Leakmaster
4. First Aid Measures
4.1 Symptoms of Exposure by Route
SWALLOWED
Small amounts ingested incidental to normal handling will have little or no effect.
EYE
Paste in contact with the eye may cause irritation and should be promptly removed by flushing.
SKIN
Prolonged skin contact may cause slight irritation
INHALED
Unlikely to cause adverse effects unless exposed to highly concentrated vapours. (Considered unlikely in any normal circumstances
of use)
4.2 First Aid Instructions
SWALLOWED
Do not induce vomiting. Rinse mouth clear with water and give two glasses to drink. If symptoms persist seek prompt medical help.
EYE
Immediately: Hold eye open and flush with clean water for at least 15 minutes. While flushing, gently pull upper and lower eyelids
away from eyes and ensure carefully flushed. If symptoms persist seek prompt medical attention.
SKIN
Remove contaminated clothing. Wash affected area with soap and water for at least 10 minutes. If symptoms persist seek medical
assistance.
INHALED
Remove patient (while wearing SCBA if concentrations are high) to fresh air. Allow to rest. Rinse mouth and nose with water.
Provide artificial respiration if breathing stops. Seek prompt medical attention unless recovery is virtually immediate.
FIRST AID FACILITIES
Provide normal industrial first aid facilities including eye-wash stations and safety showers as appropriate.
Notes to Physician (for symptoms of over-exposure to this product see above)
Possible symptoms of Chronic Health Effects
No chronic effects reported
Possible aggravated pre-existing conditions
None reported.
Suggested treatment for acute symptoms, known antidotes
Provide supportive care and treatment based on the patient's reactions to the exposure. For further information contact
the :
POISONS INFORMATION CENTRE 13 11 26 in all States
Issue Date 8/03/2004 Page 2 of 4
Leakmaster Version 1.0
Reference No 0002
5. Fire Fighting Measures
5.1 Flammability and Explosion Hazards
Product is combustible but slow to ignite.
5.2 Hazardous Combustion Products
Thermal decomposition emits CO X, nitric oxides, ammonia , trace amounts of chlorine, phenol, HCN and isocyanate vapour
5.3 Suitable Extinguishing Media
CO2, dry chemicals, or water. For large fires in warehouse or product areas use water jets or alcohol-resistant foam.
Hazchem Code: not allocated
5.4 Precautions for Fire Fighters and Special Equipment
Wear fully encapsulated suit with SCBA. Avoid all contact with product or run-off. Contain run-off for later collection and controlled
disposal.
6. Accidental Release Measures
6.1 Emergency Procedures 鈥? Spills and Leaks (See Section 13 for disposal considerations)
Switch off or remove all potential ignition sources. Prevent material entering drains or waterways. Scrape up and collect in suitable
containers. Fit lids and place container in a safe area to await disposal or recovery.
7. Handling and Storage
7.1 Handling Advice
Use in well-ventilated areas.
7.2 Storage Advice
Store in a cool, dry and well-ventilated area. Keep away from foodstuffs.
8. Exposure Controls/ Personal Protection
8.1 Exposure Standards
No exposure standards have been set by the NOHSC for this product or its ingredients in the form sold.
Substance TWA STEL
鈥? 鈥?
鈥?
8.2 Engineering Control Methods
Ensure good ventilation in the workplace.
8.3 Personal Protective Equipment
Respiratory Protection
Not usually required where ventilation is good. If vapours are in high concentration, typically in poorly ventilated enclosed areas,
wear respirator fitted with an organic vapour filter to AS 1715 & 1716.
Eye Protection
Not normally required. If mists or splashes are likely wear safety goggles or full face shield to AS 1337.
Gloves
When applying the product wear neoprene, nitrile or butyl rubber gloves to AS 2161.
Clothing
Wear Tyvec or cotton coveralls fastened at the neck and wrists. Supplement with PVA apron if required.
Issued 8/03/2004 Page 3 of 4
Version1.0
Reference No 0002
Leakmaster
9. Physical and Chemical Properties
Appearance: Odour:
Pasty grey coloured paste. slight hydrocarbon odour
Freezing/ Boiling
n.d. n.d.
Melting Point: Point:
n.d.
Vapour
1.2 鈥? 1.3 g/cm鲁
Density:
Pressure:
Solubility Insoluble Volatiles: 7% approximately
in water : Percent
Flammability n.d.
> 66潞C
Flash Point:
Limits:
n.d.
Ignition Point:
Other Incompatible in contact with aminos and alcohols. An exothermic reaction results if such contact occurs.
Properties
10. Stability and Reactivity
Product is stable in normal circumstances. In contact with incompatibles listed above an exothermic reaction will take place. Contact
with water or high humidity in closed containers may result in pressure increase by formation of CO2 and may result in violent rupture
of the container.
11. Toxicological Information
No relevant data.
12. Ecological Consideration
Prior to curing the product is regarded as presenting a slight hazard to water. Once cured adverse effects are largely unknown but it is
expected that cured product will be inert. Do not allow product or fire water run-off to enter drains or waterways,
13. Disposal Considerations
Disposal of waste product and fire water run-off must be in accordance with local regulations. Product is a suitable candidate for
incineration at authorised waste disposal facilities.
14. Transport Information
Legislation under the Dangerous Good Codes of Australia, the IMDG and IATA does not apply to this product.
15. Regulatory Information
No special labelling requirements under the Code of Practice for the labelling of Workplace Substances(NOHSC:2012[1994]), the
ADG Code or the SUSDP. All components are listed on the AICS.
16. Other Information
Date Prepared/Amended: 23-01-04 New version (1.0) to comply with National Code of Practice for the Preparation of Material
Safety Data Sheets 2nd Edition NOHSC: 2011 (2003)
Data Sources used: in the preparation of this MSDS include: 鈥淐hempendium鈥? published in CD format by CCOHS Canada
2003 - 4. 鈥淭OMES鈥? a CD database published by Micromedex, USA, 鈥淗azardous Properties of Industrial Materials鈥? Van
Nostrand Rheinhold NY, USA . 鈥淟ist of Designated Hazardous Substances鈥? NOHSC 10005: 1999, 鈥淣ational Exposure
Standards鈥? NOHSC 1003: 1995 . Abbreviations used: n.d = not determined, n.a = not applicable, n.all =not allocated,
SUSDP = Standard for the Uniform Scheduling of Drugs and Poisons, ADG = Australian Dangerous Goods Code,
IATA = International Air Transport Association (Dangerous Goods Regulations), IMDG = International Maritime Dangerous
Goods (Code).
Disclaimer
No representative of Corkjoint (Vic) Pty Ltd or any other person has authority to add to, or alter in any way, any MSDS or the information supplied
thereon. Any alterations render this MSDS invalid. The information contained herein is believed by Corkjoint (Vic) Pty Ltd and SSC Pty Ltd to be
accurate at the issue date shown and in accordance with information available to us. Persons dealing with the products referred to in this MSDS do
so at their own risk since their actions are beyond our control. Corkjoint (Vic) Pty Ltd and SSC Pty Ltd accepts no liability whatsoever for damage or
injury arising from the use of the information contained in this document. Users shall determine the suitability of the product for the intended use and
assume all risks and liability in connection with the intended use.
Version 1.0 Issue Date 8/03/2004 Page 4 of 4
Leakmaster Reference No 0002
|