MATERIAL SAFETY DATA SHEET
SECTION I - MANUFACTURER IDENTIFICATION
ALLSTATES COATINGS COMPANY INFORMATION PHONE: (903) 845-6436
P.O. BOX 1633 EMERGENCY PHONE: (800) 424-9300
100 LEE STREET PREPARED BY: CHAD PAYTON
GLADEWATER, TEXAS 75647 DATE REVISED: 8/16/00
SECTION II - PRODUCT IDENTIFICATION
PRODUCT NAME: CHEP BLUE LATEX PAINT
PRODUCT CODE: ALT-507
SECTION III - HAZARDOUS INGREDIENTS / SARA III INFORMATION
OSHA PEL ACGIH TLV
HAZARDOUS COMPONENTS CAS # mg/M3 mg/M3 OTHER % (OPT)
Water 7732-18-5 <50.00
Phthlo Blue NA NA < 5.00
Property Additives NA NA < 3.00
Calcium Carbonate 1317-65-3 10.0 10.0 <20.00
Acrylic Polymer 25067-01-0 NA NA <20.00
Titanium Pigment 13463-67-7 6.0 10.0 < 5.00
Health: 1 Flammability: 0 Reactivity: 0 Ratings based on NFPA
SECTION IV - PHYSICAL / CHEMICAL CHARACTERISTICS
BOILING POINT: 212掳F
SPECIFIC GRAVITY (H2O=1): 1.22
VAPOR PRESSURE (mm Hg): NA
MELTING POINT: NA
VAPOR DENSITY (AIR=1): Heavier
EVAPORATION RATE (Butyl Acetate=1): Water
SOLUBILITY in WATER: Soluble
APPEARANCE and ODOR: Blue, No Odor
SECTION V - FIRE AND EXPLOSION HAZARD DATA
FLASH POINT (Method Used): NA
FLAMMABLE LIMITS: LEL: NA UEL: NA
EXTINGUISHING METHOD: Water, all purpose (ABC) dry chemical, CO2 foam.
SPECIAL FIRE FIGHTING PROCEDURES: Adequate breathing apparatus should be worn when
fighting fires in enclosed areas.
UNUSUAL FIRE AND EXPLOSION HAZARDS: NON FLAMMABLE in EMULSION STATE.
NOTE: In Asphalt State: Small fires-use dry chemical,CO2, Halon Water spray or standard foam.
Large fires-use water spray, fog or standard foam.
SECTION VI - REACTIVITY DATA
CONDITIONS TO AVOID: Avoid heat, sparks or open flame.
INCOMPATABILITY (MATERIAL TO AVOID): Any strong oxidizing agents.
HAZARDOUS POLYMERIZATION: Will not occur.
STABILITY: Stable.
SECTION VII - HEALTH HAZARD DATA
CARCINOGENITY: NTP? No IARC MONOGRAPHS? No OSHA REGULATED? No
SIGNS and SYMPTONS of EXPOSURE:
EYES: May cause mild irritation.
SKIN: May cause slight to mild irritation.
INHALATION: May cause dizziness, headache, nausea.
MEDICAL CONDITIONS GENERALLY AGGRAVATED BY EXPOSURE: Individuals with chronic
respiratory disorders may be adversely affected by any fume or airborne particle matter exposure.
EMERGENCY and FIRST AID PROCEDURES:
INHALATION: Remove from contaminated area. If breathing is difficult, give oxygen. If breathing
stops, give artificial respiration - Call Physician.
INGESTION: If conscious give 1 to 2 glasses of milk or walter, induce vomiting and call a
physician. NEVER GIVE ANYTHING BY MOUTH TO AN UNCONSCIOUS PERSON.
EYES: Immediately flush with water for at least 15 minutes holding eyelids open. Call a physician
if irritation developes.
SKIN: Remove contaminated clothing and launder before reuse. Wash skin with soap and water.
SECTION VIII - PRECAUTIONS FOR SAFE HANDLING AND USE
STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED: Remove all ignition
sources. Avoid breathing vapors. Open all windows and doors. Keep out of sewers and water
sources. Advise proper authorities.
WASTE DISPOSAL METHODS: As provided under Resources Conservation and Recovery Act
(RCRA), and in accordance with Federal, State and Local Regulations.
PRECAUTIONS TO BE TAKEN IN HANDLING AND STORING: Keep containers closed when
not in use. Do not handle or store near heat , sparks or open flame or strong oxidants.
OTHER PRECAUTIONS: Avoid breathing vapors. Avoid prolonged or repeated skin contact.
SECTION IX - CONTROL MEASURES
RESPIRATORY PROTECTION: Use a NIOSH approved respirator.
VENTIALTION: Must be adequate, use local exhaust as needed.
PROTECTIVE GLOVES: Use rubber gloves as needed.
EYE PROTECTION: Use goggles or face shield.
OTHER PROTECTIVE CLOTHING or EQUIPMENT: As needed to avoid skin contact.
WORK / HYGENIC PRACTICES: Wash skin and exposed clothing throughly with soap and water
after use.
Disclaimer: Information in this MSDS and Environmental Data Sheet was obtained from sources which we believe are reliable.
However, the information is provided without any representation or warranty, expressed or implied, regarding its accuracy or
completeness.
|