MATERIAL SAFETY DATA SHEET
SECTION I - MANUFACTURER IDENTIFICATION
ALLSTATES COATINGS COMPANY INFORMATION PHONE: (903) 845-6436
P.O. BOX 1633 EMERGENCY PHONE: (800) 424-9300
100 LEE STREET PREPARED BY: CHAD PAYTON
GLADEWATER, TEXAS 75647 DATE REVISED: 9/16/05
SECTION II - PRODUCT IDENTIFICATION
PRODUCT NAME: Roof Coating
PRODUCT CODE: ALT-210
SECTION III - HAZARDOUS INGREDIENTS / SARA III INFORMATION
OSHA PEL ACGIH TLV
HAZARDOUS COMPONENTS CAS # mg/M3 mg/M3 OTHER % (OPT)
Water 7732-18-5 <30.00
Asphalt 8052-42-4 5mg/m3 5mg/m3 <20.00
Hydrous Aluminum Silicates 1302-78-9 5mg/m3 5mg/m <10.00
3
Cellulose Fibers 9004-34-6 5mg/m3 5mg/m3 <10.00
Acetic Acid 64-19-7 10 ppm 10 ppm <1.00
Potassium Bichromate 7778-50-9 0.1mg/m3 0.5mg/m < 1.00
3
Health: 1 Flammability: 0 Reactivity: 0 Ratings based on NFPA
SECTION IV - PHYSICAL / CHEMICAL CHARACTERISTICS
BOILING POINT: 212掳F
SPECIFIC GRAVITY (H2O=1): 1.00 - 1.05
VAPOR PRESSURE (mm Hg) 77飩癋: 23.7mm of hg
MELTING POINT: NA
VAPOR DENSITY (AIR=1): >1
EVAPORATION RATE (Butyl Acetate=1) @ 77飩癋: <1
SOLUBILITY in WATER: Soluble
APPEARANCE and ODOR: Black Thixotropic Liquid
SECTION V - FIRE AND EXPLOSION HAZARD DATA
FLASH POINT (Method Used): NA
FLAMMABLE LIMITS: LEL: NA UEL: NA
EXTINGUISHING METHOD: Water, all purpose (ABC) dry chemical, CO2 foam. Cool containers
exposed to heat.
SPECIAL FIRE FIGHTING PROCEDURES: Minimize breathing vapors, gases or fumes of
decomposition products. Do not enter any enclosed or confined fire space without proper
protective equipment, including self鈥揷ontained breathing apparatus.
UNUSUAL FIRE AND EXPLOSION HAZARDS: Material may foam if heated above 212飩癋.
SECTION VI - REACTIVITY DATA
CONDITIONS TO AVOID: Auto-ignition temperature known.
INCOMPATABILITY (MATERIAL TO AVOID): May react with strong oxidizing materials.
HAZARDOUS POLYMERIZATION: Will not occur.
STABILITY: Stable.
SECTION VII - HEALTH HAZARD DATA
CARCINOGENITY: NTP? No IARC MONOGRAPHS? No OSHA REGULATED? No
SIGNS and SYMPTONS of EXPOSURE:
Fumes from product can be unpleasant, may cause nausea, headache and irritating to eyes, skin,
and respiratory tract.
MEDICAL CONDITIONS GENERALLY AGGRAVATED BY EXPOSURE: Individuals with chronic
respiratory disorders may be adversely affected by any fume or airborne particle matter exposure.
EMERGENCY and FIRST AID PROCEDURES:
EYES: If this product comes in contact with eyes, Flush eye with plenty of water for at least 15
minutes and seek medical attention.
SKIN: If this product comes in contact with skin, wash with soap and plenty of water.
INHALATION: If respiratory discomfort occurs, remove to fresh air. If discomfort continues,
administer oxygen and get medical attention.
SECTION VIII - PRECAUTIONS FOR SAFE HANDLING AND USE
STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED: Dike or contain spill
with earth, floor dry, sand etc. Ventilate the area. Absorb spill with suitable absorbent material and
place in a closed container. Keep product out of sewers and waterways by diking or impounding.
Advise authorities if product has entered or may enter sewers or waterways. Assure conformity
with applicable governmental regulations.
WASTE DISPOSAL METHODS: As provided under Resources Conservation and Recovery Act
(RCRA), and in accordance with Federal, State and Local Regulations.
PRECAUTIONS TO BE TAKEN IN HANDLING AND STORING: Vapors are heavier than air and
may travel along the ground or be moved by ventilation to locations distant from the point of
material handling or the work area. Avoid prolonged or repeated inhalation of vapors or spray
mists. Avoid prolonged or repeated skin contact. Adhere to good hygienic practices. Use with
adequate ventilation. Store in a cool, dry place, out of direct sunlight and away from heat, sparks,
and flame. DO NOT FREEZE.
OTHER PRECAUTIONS: Avoid breathing vapors. Avoid prolonged or repeated skin contact.
SECTION IX - CONTROL MEASURES
RESPIRATORY PROTECTION: Use a NIOSH approved respirator in confined areas or with
vapors in high concentrations.
VENTIALTION: Must be adequate, use local exhaust as needed.
PROTECTIVE GLOVES: Use rubber gloves as needed.
EYE PROTECTION: Use goggles or face shield.
OTHER PROTECTIVE CLOTHING or EQUIPMENT: As needed to avoid skin contact.
WORK / HYGENIC PRACTICES: Wash skin and exposed clothing thoroughly with soap and
water after use.
Disclaimer: Information in this MSDS and Environmental Data Sheet was obtained from sources which we believe are reliable.
However, the information is provided without any representation or warranty, expressed or implied, regarding its accuracy or
completeness.
|