Aitken Freeman Pty Ltd
Factory 7, 7-9 Brough St, Springvale VIC 3171
PO Box 548, Noble Park VIC 3174
Phone: (03) 9701 3955 Fax: (03) 9701 3956
Internet: www.aitkenfreeman.com
e-mail: sales@aitkenfreeman.com
MATERIAL SAFETY DATA SHEET 鈥? PAGE 1 OF 4
TECSEAL WB BASE
This product is classified as hazardous according to criteria of NOHSC
Section 1 鈥? Identification of the Material and Supplier
PRODUCT (MATERIAL) NAME: TECSEAL WB BASE
OTHER NAMES:
RECOMMENDED USES: Base component of a solvent free epoxy coating for concrete
SUPPLIER NAME/ADDRESS: Aitken Freeman Pty Ltd 鈥? Factory 7, 7-9 Brough St, Springvale VIC 3171
TELEPHONE NUMBER: (03) 9701 3955 FACSIMILE NUMBER: (03) 9701 3956
EMERGENCY PHONE NUMBER: (03) 9701 3955 HOURS: 0800-1700 Mon-Fri
Section 2 鈥? Hazards Identification
POISONS SCHEDULE: S5
HAZARD CLASSIFICATION: Classified as a HAZARDOUS SUBSTANCE according to criteria of NOHSC.
Classified as NON DANGEROUS GOODS according to criteria of ADG Code.
RISK PHRASES: R22: Harmful if swallowed
R41: Risk of serious damage to the eyes
R43: May cause sensitisation by skin contact
R37/R38: Irritating to respiratory system and skin
SAFETY PHRASES: S20: When using, do not eat or drink
S23: Do not breathe vapour
S24/25: Avoid contact with skin and eyes
S28: After contact with skin, wash immediately with plenty of soap suds.
S36: Wear suitable protective clothing
S38: In case of insufficient ventilation, wear suitable respiratory equipment
Section 3 鈥? Composition / Information on Ingredients
INGREDIENTS:
Chemical Name: Proportion: CAS Number:
Bisphenol A Resin > 60 % 25068-38-6
C12-C14 Alkyl glycidyl ether 10 鈥? 30 % 68909-97-2
Balance of formulation consists of ingredients below cut-off rates or ingredients determined not to be hazardous.
Section 4 鈥? First Aid Measures
INHALATION: If inhaled, remove patient from contaminated area to fresh air. Lay patient down,
keep warm and rested. Encourage patient to blow nose and clear breathing
passages. If not breathing, apply artificial respiration. Seek medical attention if
irritation persists.
INGESTION: If swallowed, DO NOT induce vomiting. Rinse mouth with plenty of water. Seek
immediate medical advice from a doctor or the Poisons Information Centre
(13 11 26 Australia-wide).
SKIN: If skin or hair contact occurs, remove all contaminated clothing and wash before
reuse. Wash off skin and/or hair with running water and soap if available. Seek
medical assistance if irritation persists.
EYES: If product comes into contact with eyes, hold eyelids apart and flush the eye
continuously with fresh running water. If pain persists or recurs seek medical
attention. Removal of contact lenses after an eye injury should only be
undertaken by skilled personnel.
FIRST AID FACILITIES: Eye wash and normal washroom facilities.
ADVICE TO DOCTOR: Treat symptomatically. POISON INFORMATION CENTRE 鈥? 13 11 26 Australia-
wide.
Material Safety Data Sheet 鈥? Tecseal WB Base 鈥? Page 1 of 4 鈥? Review Date 1st March 2008
MATERIAL SAFETY DATA SHEET 鈥? PAGE 2 OF 4
Section 5 鈥? Fire Fighting Measures
EXTINGUISHING MEDIA: Carbon dioxide, dry chemical, foam or water fog
FIRE FIGHTING: Wear breathing apparatus and gloves. Avoid bodily contact with substance or
run-off. If significant quantity of this product is involved in a fire, contact the fire
brigade.
FIRE / EXPLOSION HAZARD: This product is classified as a C1 combustible product. There is no risk of an
explosion from this product under normal circumstances if it is involved in a fire.
Fire decomposition products from this product may be toxic if inhaled. Take
appropriate protective measures.
Section 6 鈥? Accidental Release Measures
EMERGENCY PROCEDURES: Product is slippery when spilt 鈥? avoid accidents by cleaning up any spills
immediately. Wear gloves, protective goggles and appropriate protective
equipment to avoid eye and skin contact. If significant chance that product
vapours or mists are likely to build up in the spill area, a respirator should also be
worn. Isolate and contain spill and soak up with inert material such as clay or
sand. Prevent by any means possible the material from entering storm water
drains, waterways, basements or workpits. Collect in suitable containers and
ensure these are correctly labelled. Ensure area is thoroughly ventilated before
recommencing work.
METHODS AND MATERIALS FOR CONTAINMENT AND CLEAN UP:
Contain and collect spills as detailed above. Refer to State Land Waste
Management Authority for disposal considerations.
Section 7 鈥? Handling and Storage
PRECAUTIONS FOR SAFE HANDLING:
Wear protective goggles or face shield and rubber gloves and barrier cream to
prevent eye and skin contamination. Contact lenses pose a special hazard as they
may absorb irritants. Suitable protective clothing, PVC gloves and boots should
be worn. Use in a well ventilated area, preferably outdoors. General exhaust is
normally adequate. If risk of overexposure exists, wear SAA approved
respirator.
CONDITIONS FOR SAFE STORAGE:
Keep containers tightly sealed when not in use. Store in a cool, dry, well
ventilated place out of direct sunlight. Keep away from strong acids, bases and
oxidising agents.
INCOMPATIBILITIES: No restrictions.
Section 8 鈥? Exposure Controls / Personal Protection
NATIONAL EXPOSURE STANDARDS:
No exposure standards have been established for this product by NOHSC. Refer
to limits for individual constituents listed below:
Bisphenol A epoxy resin 鈥? none assigned for material, but contains
Epichlorohydrin: TLV TWA: 0.1ppm, 0.38mg/m3 鈥? skin
ES TWA: 0.1ppm, 0.4mg/m3
BIOLOGICAL LIMIT VALUES: Not established for the product.
ENGINEERING CONTROLS: If used in limited ventilation, ensure adequate ventilation to maintaine exposure
levels are kept below standards, by using a local exhaust. Keep containers closed
when not in use.
PERSONAL PROTECTION: Avoid unnecessary contact as good work practice. Wash contaminated clothing
and protective equipment before storing and reuse. Wash hands before eating,
smoking, or using the toilet.
RESPIRATORY PROTECTION: It is usually safe not to use respiratory protection. However, where engineering
controls are not effective in controlling airborne exposure, the use of a mask or
other device is appropriate. For assistance in selecting suitable equipment consult
AS/NZ1715.
EYE PROTECTION: Eye protective measures are normally necessary, and are suggested when using
this product. Consult AS1336 and AS/NZ1337.
PROTECTIVE GLOVES: Rubber, PVC or other protective gloves are necessary, and desirable, especially if
this product is being used frequently or for lengthy periods. Consult AS2161 for
guidance.
CLOTHING: Clean overalls should be worn, preferably with an apron. Consult AS2919 for
clothing guidance.
SAFETY FOOTWEAR: Wearing safety boots is advisory. Consult AS/NZ2210 for advice on Occupational
Protective Footwear.
Material Safety Data Sheet 鈥? Tecseal WB Base 鈥? Page 2 of 4 鈥? Review Date 1st March 2008
MATERIAL SAFETY DATA SHEET 鈥? PAGE 3 OF 4
Section 9 鈥? Physical and Chemical Properties
APPEARANCE (COLOUR, PHYSICAL FORM, SHAPE):
Transparent liquid
ODOUR: Nil
SOLUBILITY: Insoluble
VAPOUR DENSITY: Not available VAPOUR PRESSURE: Negligible
MELTING POINT: Not applicable BOILING POINT: Not available
FREEZING POINT: Not available SPECIFIC GRAVITY: 1.0 鈥? 1.1
FLASH POINT: > 93掳C UPPER FLAMMABLE LIMIT: Not established
LOWER FLAMMABLE LIMIT: Not established AUTOIGNITION TEMPERATURE:Unknown
VOLATILE ORGANIC COMPOUNDS (VOC) CONTENT: No data available
Section 10 鈥? Stability and Reactivity
CHEMICAL STABILITY: Stable
CONDITIONS TO AVOID: Keep away from strong acids, bases and oxidising agents.
INCOMPATIBLE MATERIALS: No restrictions
HAZARDOUS DECOMPOSITION PRODUCTS:
On burning may emit toxic fumes, including carbon and nitrogen oxides.
HAZARDOUS REACTIONS: None
Section 11 鈥? Toxicological Information
TOXICOLOGY INFORMATION: No toxicity data is available for this product.
HEALTH EFFECTS FROM THE LIKELY ROUTES OF EXPOSURE:
INHALATION: Not normally a hazard at normal temperatures, however at elevated
temperatures vapour may be irritating to respiratory system. Inhalation of
vapour may result in nausea and headache.
INGESTION: Swallowing may result in nausea, vomiting, abdominal pain and diarrhoea.
SKIN: Is irritating and may cause drying of the skin. May lead to dermatitis and in some
cases sensitisation. The material may accentuate pre-existing skin conditions.
EYES: Irritating and abrasive to the eyes and is capable of causing temporary
impairment of vision, eye inflammation and ulceration.
CHRONIC EFFECTS: May causes sensitisation in susceptible individuals by skin contact. Repeated or
prolonged skin contact may result in allergic contact dermatitis.
Section 12 鈥? Ecological Information
ECOTOXICITY: Not available
PERSISTENCE AND DEGRADIBILITY:
Not available
MOBILITY: Not available
ENVIRONMENTAL PROTECTION:
Product is biodegradable and will not accumulate in soil or water or cause long
term problems.
Section 13 鈥? Disposal Considerations
Recycle wherever possible. Consult manufacturer for recycling options or consult local or regional waste
management authority for disposal if no suitable treatment or disposal facility can be identified. Dispose of by: Burial
in a licenced land-fill or Incineration in a licenced apparatus after admixture with suitable combustible material)
Decontaminate empty containers. Observe all label safeguards until containers are cleaned and destroyed.
Containers may still present a chemical hazard/ danger when empty. Return to supplier for reuse/ recycling if
possible. Otherwise: If container can not be cleaned sufficiently well to ensure that residuals do not remain or if the
container cannot be used to store the same product, then puncture containers, to prevent re-use, and bury at an
authorised landfill. Where possible retain label warnings and MSDS and observe all notices pertaining to the product.
Section 14 鈥? Transport Information
This material is a Non Dangerous Good according to the Australian Code for the Transport of Dangerous Goods by
Road and Rail.
UN NUMBER: None assigned
UN PROPER SHIPPING NAME: None assigned
DANGEROUS GOODS CLASS: None assigned
SUBSIDIARY RISK: None assigned
PACKING GROUP: None assigned
SPECIAL PRECAUTIONS PER USER:
Keep containers tightly sealed, store in a cool, dry, well ventilated place out of
direct sunlight. Keep away from strong acids, bases and oxidising agents.
HAZCHEM CODE: None assigned
Material Safety Data Sheet 鈥? Tecseal WB Base 鈥? Page 3 of 4 鈥? Review Date 1st March 2008
MATERIAL SAFETY DATA SHEET 鈥? PAGE 4 OF 4
Section 15 鈥? Regulatory Information
POISON SCHEDULE: S5
OHS: Unregulated
ENVIRONMENTAL: Unregulated
ADDITIONAL NATIONAL AND/OR INTERNATIONAL REGULATORY INFORMATION:
Unregulated
Section 16 鈥? Other Information
DATE OF PREPARATION OR LAST REVISION OF MSDS:
1st March 2008
CONTACT POINT: Aitken Freeman Pty Ltd
(03) 9701 3955
LITERATURE REFERENCES / SOURCES OF DATA:
Material Safety Data Sheets from Suppliers
List of Designated Substances 鈥? Worksafe Australia (on-line)
Australian Dangerous Goods Code 6th Edition
Standard for the Uniform Scheduling of Drugs and Poisons No 19
The information presented herein has been compiled from sources considered to be dependable and is accurate to
the best of seller's knowledge, however seller makes no warranty whatsoever, expressed, implied, or of
merchantability regarding to the accuracy of such data or the results to be obtained from the use thereof. Seller
assumes no responsbility for injury to the buyer or third persons or for any damage to property. Buyer assumes all
risks.
Material Safety Data Sheet 鈥? Tecseal WB Base 鈥? Page 4 of 4 鈥? Review Date 1st March 2008
Aitken Freeman Pty Ltd
Factory 7, 7-9 Brough St, Springvale VIC 3171
PO Box 548, Noble Park VIC 3174
Phone: (03) 9701 3955 Fax: (03) 9701 3956
Internet: www.aitkenfreeman.com
e-mail: sales@aitkenfreeman.com
MATERIAL SAFETY DATA SHEET 鈥? PAGE 1 OF 4
TECSEAL WB HARDENER
This product is classified as hazardous according to criteria of NOHSC
Section 1 鈥? Identification of the Material and Supplier
PRODUCT (MATERIAL) NAME: TECSEAL WB HARDENER
OTHER NAMES:
RECOMMENDED USES: Hardener component of a solvent free epoxy coating for concrete
SUPPLIER NAME/ADDRESS: Aitken Freeman Pty Ltd 鈥? Factory 7, 7-9 Brough St, Springvale VIC 3171
TELEPHONE NUMBER: (03) 9701 3955 FACSIMILE NUMBER: (03) 9701 3956
EMERGENCY PHONE NUMBER: (03) 9701 3955 HOURS: 0800-1700 Mon-Fri
Section 2 鈥? Hazards Identification
POISONS SCHEDULE: S5
HAZARD CLASSIFICATION: Classified as a HAZARDOUS SUBSTANCE according to criteria of NOHSC.
Classified as NON DANGEROUS GOODS according to criteria of ADG Code.
RISK PHRASES: R20/21/22: Harmful by inhalation, by contact with skin or if swallowed
R43: May cause sensitisation by skin contact
R36/37/R38: Irritating to eyes, respiratory system and skin
R52/53: Harmful to aquatic organisms, may cause long-term adverse effects in
the aquatic environment.
SAFETY PHRASES: S20: When using, do not eat or drink
S23: Do not breathe vapour
S24/25: Avoid contact with skin and eyes
S28: After contact with skin, wash immediately with plenty of soap suds.
S36: Wear suitable protective clothing
S38: In case of insufficient ventilation, wear suitable respiratory equipment
Section 3 鈥? Composition / Information on Ingredients
INGREDIENTS:
Chemical Name: Proportion: CAS Number:
3,6,9,12-Tetraaazatetradecane-1, 14-diamine < 2% 4067-16-7
Non hazardous ingredients > 98%
Balance of formulation consists of ingredients below cut-off rates or ingredients determined not to be hazardous.
Section 4 鈥? First Aid Measures
INHALATION: If inhaled, remove patient from contaminated area to fresh air. Lay patient down,
keep warm and rested. Encourage patient to blow nose and clear breathing
passages. If not breathing, apply artificial respiration. Seek medical attention if
irritation persists.
INGESTION: If swallowed, DO NOT induce vomiting. Rinse mouth with plenty of water. Seek
immediate medical advice from a doctor or the Poisons Information Centre
(13 11 26 Australia-wide).
SKIN: If skin or hair contact occurs, remove all contaminated clothing and wash before
reuse. Wash off skin and/or hair with running water and soap if available. Seek
medical assistance if irritation persists.
EYES: If product comes into contact with eyes, hold eyelids apart and flush the eye
continuously with fresh running water. If pain persists or recurs seek medical
attention. Removal of contact lenses after an eye injury should only be
undertaken by skilled personnel.
FIRST AID FACILITIES: Eye wash and normal washroom facilities.
ADVICE TO DOCTOR: Treat symptomatically. POISON INFORMATION CENTRE 鈥? 13 11 26 Australia-
wide.
Material Safety Data Sheet 鈥? Tecseal WB Hardener 鈥? Page 1 of 4 鈥? Review Date 1st March 2008
MATERIAL SAFETY DATA SHEET 鈥? PAGE 2 OF 4
Section 5 鈥? Fire Fighting Measures
EXTINGUISHING MEDIA: Carbon dioxide, dry chemical, foam or water fog
FIRE FIGHTING: Wear breathing apparatus and gloves. Avoid bodily contact with substance or
run-off. If significant quantity of this product is involved in a fire, contact the fire
brigade.
FIRE / EXPLOSION HAZARD: This product is classified as flammable. There is no risk of an explosion from this
product under normal circumstances if it is involved in a fire. Fire decomposition
products from this product may be toxic if inhaled. Take appropriate protective
measures.
Section 6 鈥? Accidental Release Measures
EMERGENCY PROCEDURES: Product is slippery when spilt 鈥? avoid accidents by cleaning up any spills
immediately. Wear gloves, protective goggles and appropriate protective
equipment to avoid eye and skin contact. If significant chance that product
vapours or mists are likely to build up in the spill area, a respirator should also be
worn. Isolate and contain spill and soak up with inert material such as clay or
sand. Prevent by any means possible the material from entering storm water
drains, waterways, basements or workpits. Collect in suitable containers and
ensure these are correctly labelled. Ensure area is thoroughly ventilated before
recommencing work.
METHODS AND MATERIALS FOR CONTAINMENT AND CLEAN UP:
Contain and collect spills as detailed above. Refer to State Land Waste
Management Authority for disposal considerations.
Section 7 鈥? Handling and Storage
PRECAUTIONS FOR SAFE HANDLING:
Wear protective goggles or face shield and rubber gloves and barrier cream to
prevent eye and skin contamination. Contact lenses pose a special hazard as they
may absorb irritants. Suitable protective clothing, PVC gloves and boots should
be worn. Use in a well ventilated area, preferably outdoors. General exhaust is
normally adequate. If risk of overexposure exists, wear SAA approved dust
respirator.
CONDITIONS FOR SAFE STORAGE:
Keep containers tightly sealed when not in use. Store in a cool, dry, well
ventilated place out of direct sunlight. Keep away from strong acids, bases and
oxidising agents.
INCOMPATIBILITIES: No restrictions.
Section 8 鈥? Exposure Controls / Personal Protection
NATIONAL EXPOSURE STANDARDS:
No exposure standards have been established for this product or its constituents
by NOHSC.
BIOLOGICAL LIMIT VALUES: Not established for the product.
ENGINEERING CONTROLS: If used in limited ventilation, ensure adequate ventilation to maintaine exposure
levels are kept below standards, by using a local exhaust. Keep containers closed
when not in use.
PERSONAL PROTECTION: Avoid unnecessary contact as good work practice. Wash contaminated clothing
and protective equipment before storing and reuse. Wash hands before eating,
smoking, or using the toilet.
RESPIRATORY PROTECTION: It is usually safe not to use respiratory protection. However, where engineering
controls are not effective in controlling airborne exposure, the use of a mask or
other device is appropriate. For assistance in selecting suitable equipment consult
AS/NZ1715.
EYE PROTECTION: Eye protective measures are normally necessary, and are suggested when using
this product. Consult AS1336 and AS/NZ1337.
PROTECTIVE GLOVES: Rubber, PVC or other protective gloves are necessary, and desirable, especially if
this product is being used frequently or for lengthy periods. Consult AS2161 for
guidance.
CLOTHING: Clean overalls should be worn, preferably with an apron. Consult AS2919 for
clothing guidance.
SAFETY FOOTWEAR: Wearing safety boots is advisory. Consult AS/NZ2210 for advice on Occupational
Protective Footwear.
Material Safety Data Sheet 鈥? Tecseal WB Hardener 鈥? Page 2 of 4 鈥? Review Date 1st March 2008
MATERIAL SAFETY DATA SHEET 鈥? PAGE 3 OF 4
Section 9 鈥? Physical and Chemical Properties
APPEARANCE (COLOUR, PHYSICAL FORM, SHAPE):
Transparent (or pigmented) liquid
ODOUR: Strong amine odour
SOLUBILITY: Partially soluble
VAPOUR DENSITY: Not available VAPOUR PRESSURE: 1.0kPa at 20掳C
MELTING POINT: Not applicable BOILING POINT: >100掳C at 100kPa
FREEZING POINT: Not available SPECIFIC GRAVITY: 1.25
FLASH POINT: > 110掳C UPPER FLAMMABLE LIMIT: Not established
LOWER FLAMMABLE LIMIT: Not established AUTOIGNITION TEMPERATURE:Unknown
VOLATILE ORGANIC COMPOUNDS (VOC) CONTENT: No data available
Section 10 鈥? Stability and Reactivity
CHEMICAL STABILITY: Stable under normal conditions
CONDITIONS TO AVOID: Keep away from strong acids and oxidising agents.
INCOMPATIBLE MATERIALS: No restrictions
HAZARDOUS DECOMPOSITION PRODUCTS:
On burning may emit toxic fumes, including carbon monoxide, amines, ammonia
and nitrogen oxides.
HAZARDOUS REACTIONS: None
Section 11 鈥? Toxicological Information
TOXICOLOGY INFORMATION: No toxicity data is available for this product.
HEALTH EFFECTS FROM THE LIKELY ROUTES OF EXPOSURE:
INHALATION: Vapour or mist is irritating to the upper respiratory tract and may cause
sensitisation. Inhalation of vapour may aggravate pre-existing conditions such as
asthma, bronchitis or emphysema. Acute effects may be chest and nasal irritation
with coughing, sneezing, heacache and nausea. Hazard increases at elevated
temperatures.
INGESTION: Harmful and highly irritating if swallowed. Swallowing may result in nausea,
vomiting, abdominal pain and diarrhoea. May cause chemical burns to the mouth,
throat and oseophagus, with extreme discomfort and pain. Considered an unlikely
route of entry in commercial/industrial environments.
SKIN: Prolonged exposure is highly irritating and may cause drying and cracking of the
skin. Material is corrosive and can cause chemical burns. Capable of causing
dermatitis and sensitisation resulting in hives, rash, itching or swelling of
extremities. Toxic effects may result from skin absorption. Sensitisation may
appear after repeated symptom-free exposures. Open cuts, abraded or irritated
skin should not be exposed to this material. This material may accentuate pre-
existing skin conditions.
EYES: Highly irritating to the eyes and is capable of causing pain and corneal burns. If
not promptly treated, can lead to permanent eye injury.
CHRONIC EFFECTS: May causes sensitisation in susceptible individuals by skin contact or inhalation.
Repeated or prolonged skin contact may result in allergic contact dermatitis.
Section 12 鈥? Ecological Information
ECOTOXICITY: Not available
PERSISTENCE AND DEGRADIBILITY:
Not available
MOBILITY: Not available
ENVIRONMENTAL PROTECTION:
Product is toxic to aquatic organisms, and may cause long-term adverse effects
in the aquatic environment. Avoid contaminating waterways.
Section 13 鈥? Disposal Considerations
Recycle wherever possible. Consult manufacturer for recycling options or consult local or regional waste
management authority for disposal if no suitable treatment or disposal facility can be identified. Dispose of by: Burial
in a licenced land-fill or Incineration in a licenced apparatus after admixture with suitable combustible material)
Decontaminate empty containers. Observe all label safeguards until containers are cleaned and destroyed.
Containers may still present a chemical hazard/ danger when empty. Return to supplier for reuse/ recycling if
possible. Otherwise: If container can not be cleaned sufficiently well to ensure that residuals do not remain or if the
container cannot be used to store the same product, then puncture containers, to prevent re-use, and bury at an
authorised landfill. Where possible retain label warnings and MSDS and observe all notices pertaining to the product.
Material Safety Data Sheet 鈥? Tecseal WB Hardener 鈥? Page 3 of 4 鈥? Review Date 1st March 2008
MATERIAL SAFETY DATA SHEET 鈥? PAGE 4 OF 4
Section 14 鈥? Transport Information
This material is a Non Dangerous Good according to the Australian Code for the Transport of Dangerous Goods by
Road and Rail.
UN NUMBER: None assigned
UN PROPER SHIPPING NAME: None assigned
DANGEROUS GOODS CLASS: None assigned
SUBSIDIARY RISK: None assigned
PACKING GROUP: None assigned
SPECIAL PRECAUTIONS PER USER:
Keep containers tightly sealed, store in a cool, dry, well ventilated place out of
direct sunlight. Keep away from strong acids, bases and oxidising agents.
HAZCHEM CODE: None assigned
Section 15 鈥? Regulatory Information
POISON SCHEDULE: S5
OHS: Unregulated
ENVIRONMENTAL: Unregulated
ADDITIONAL NATIONAL AND/OR INTERNATIONAL REGULATORY INFORMATION:
Unregulated
Section 16 鈥? Other Information
DATE OF PREPARATION OR LAST REVISION OF MSDS:
1st March 2008
CONTACT POINT: Aitken Freeman Pty Ltd
(03) 9701 3955
LITERATURE REFERENCES / SOURCES OF DATA:
Material Safety Data Sheets from Suppliers
List of Designated Substances 鈥? Worksafe Australia (on-line)
Australian Dangerous Goods Code 6th Edition
Standard for the Uniform Scheduling of Drugs and Poisons No 19
The information presented herein has been compiled from sources considered to be dependable and is accurate to
the best of seller's knowledge, however seller makes no warranty whatsoever, expressed, implied, or of
merchantability regarding to the accuracy of such data or the results to be obtained from the use thereof. Seller
assumes no responsbility for injury to the buyer or third persons or for any damage to property. Buyer assumes all
risks.
Material Safety Data Sheet 鈥? Tecseal WB Hardener 鈥? Page 4 of 4 鈥? Review Date 1st March 2008
|