Aitken Freeman Pty Ltd
Factory 7, 7-9 Brough St, Springvale VIC 3171
PO Box 548, Noble Park VIC 3174
Phone: (03) 9701 3955 Fax: (03) 9701 3956
Internet: www.aitkenfreeman.com
e-mail: sales@aitkenfreeman.com
MATERIAL SAFETY DATA SHEET 鈥? PAGE 1 OF 4
RESILOC HB BASE
This product is classified as hazardous according to criteria of NOHSC
Section 1 鈥? Identification of the Material and Supplier
PRODUCT (MATERIAL) NAME: RESILOC HB BASE
OTHER NAMES:
RECOMMENDED USES: Base component of two part epoxy repair mortar system
SUPPLIER NAME/ADDRESS: Aitken Freeman Pty Ltd 鈥? Factory 7, 7-9 Brough St, Springvale VIC 3171
TELEPHONE NUMBER: (03) 9701 3955 FACSIMILE NUMBER: (03) 9701 3956
EMERGENCY PHONE NUMBER: (03) 9701 3955 HOURS: 0800-1700 Mon-Fri
Section 2 鈥? Hazards Identification
HAZARD CLASSIFICATION: Classified as a HAZARDOUS SUBSTANCE according to criteria of NOHSC.
Classified as DANGEROUS GOODS according to criteria of ADG Code.
RISK PHRASES: R36/38: Irritating to eyes and skin.
R43: May cause sensitisation by skin contact.
R51/53: Toxic to aquatic organisms, may cause long-term adverse effects in the
aquatic environment.
SAFETY PHRASES: S24/25: Avoid contact with the skin and eyes.
S26: In case of contact with eyes, rinse immediately with plenty of water and
contact a doctor or Poisons Information Centre on 13 11 26 (Australia-wide).
S28: After contact with skin, wash immediately with water (and soap if available)
S36/37/39: Wear suitable protective clothing, gloves and eye/face protection.
S61: Avoid release to the environment.
Section 3 鈥? Composition / Information on Ingredients
INGREDIENTS:
Chemical Name: Proportion: CAS Number:
Bisphenol A epoxy resin > 60% [25068-38-6]
Crystalline silica (quartz) 1 鈥? 10 % [14808-60-7]
Glycidyl ether 1 鈥? 10 % [16096-31-4]
Inert fillers 10 鈥? 60 % [14807-96-6]
Balance of formulation consists of ingredients below cut-off rates or ingredients determined not to be hazardous.
Section 4 鈥? First Aid Measures
INHALATION: If inhaled, remove patient from contaminated area to fresh air 鈥? avoid becoming
a casualty. Remove contaminated clothing and loosen remaining clothing. Lay
patient down in a comfortable position, keep warm and rested. Seek medical
attention if further symptoms develop. If not breathing, clear airway and apply
artificial respiration.
INGESTION: If swallowed, DO NOT induce vomiting. Rinse mouth with plenty of water. Seek
immediate medical advice from a doctor or the Poisons Information Centre
(13 11 26 Australia-wide).
SKIN: If skin or hair contact occurs, remove all contaminated clothing and wash before
reuse. Flush skin and/or hair with running water and soap if available. Seek
medical assistance if irritation persists.
EYES: If product comes into contact with eyes, hold eyelids apart and flush the eye
continuously with fresh running water. If pain persists or recurs seek medical
attention. Removal of contact lenses after an eye injury should only be
undertaken by skilled personnel.
FIRST AID FACILITIES: Eye wash and normal washroom facilities.
ADVICE TO DOCTOR: Treat symptomatically. POISON INFORMATION CENTRE 鈥? 13 11 26 Australia-
wide. This product is corrosive.
Material Safety Data Sheet 鈥? Resiloc HB Base 鈥? Page 1 of 4 鈥? 1st March 2008
MATERIAL SAFETY DATA SHEET 鈥? PAGE 2 OF 4
Section 5 鈥? Fire Fighting Measures
EXTINGUISHING MEDIA: Water mist CO2, foam or dry powder.
HAZARDS FROM COMBUSTION PRODUCTS:
Combustion will release toxic fumes, including carbon and nitrogen oxides.
SPECIAL PROTECTIVE PRECAUTIONS AND EQUIPMENT FOR FIRE FIGHTERS:
Heating can cause expansion or decompostion leading to violent rupture of
containers. Keep containers cool with water spray. Fire fighters should wear self
contained breathing apparatus if risk of exposure to vapour or products of
combustion. Avoid bodily contact with substance or run off.
Section 6 鈥? Accidental Release Measures
EMERGENCY PROCEDURES: Product is slippery when spilt 鈥? avoid accidents by cleaning up any spills
immediately. Wear gloves, protective goggles and appropriate protective
equipment to avoid eye and skin contact. Isolate and contain spill and soak up
with inert material such as clay or sand. Prevent by any means possible the
material from entering storm water drains, waterways, basements or workpits.
Collect in suitable containers and ensure these are correctly labelled. Ensure area
is thoroughly ventilated before recommencing work.
METHODS AND MATERIALS FOR CONTAINMENT AND CLEAN UP:
Contain and collect spills as detailed above. Refer to State Land Waste
Management Authority for disposal considerations.
Section 7 鈥? Handling and Storage
PRECAUTIONS FOR SAFE HANDLING:
Wear protective goggles or face shield and rubber gloves and barrier cream to
prevent eye and skin contamination. Contact lenses pose a special hazard as they
may absorb irritants. Suitable protective clothing, PVC gloves and boots should
be worn. Use in a well ventilated area, preferably outdoors. General exhaust is
normally adequate. If risk of overexposure exists, wear SAA approved dust
respirator.
CONDITIONS FOR SAFE STORAGE:
Keep containers tightly sealed when not in use. Store in a cool, dry, well
ventilated place out of direct sunlight. Keep away from strong acids, bases and
oxidising agents.
INCOMPATIBILITIES: No restrictions.
Section 8 鈥? Exposure Controls / Personal Protection
NATIONAL EXPOSURE STANDARDS:
No exposure standards have been established for this product by NOHSC. Refer
to limits for individual constituents listed below:
Bisphenol A epoxy resin 鈥? none assigned for material, but contains
Epichlorohydrin: TLV TWA: 0.1ppm, 0.38mg/m3 鈥? skin
ES TWA: 0.1ppm, 0.4mg/m3
BIOLOGICAL LIMIT VALUES: Not established for the product.
ENGINEERING CONTROLS: If used in limited ventilation, ensure adequate ventilation to maintaine exposure
levels are kept below standards, by using a local exhaust. Keep containers closed
when not in use.
PERSONAL PROTECTION: Avoid unnecessary contact as good work practice. Wash contaminated clothing
and protective equipment before storing and reuse. Wash hands before eating,
smoking, or using the toilet.
RESPIRATORY PROTECTION: It is usually safe not to use respiratory protection. However, where engineering
controls are not effective in controlling airborne exposure, the use of a mask or
other device is appropriate. For assistance in selecting suitable equipment consult
AS/NZ1715.
EYE PROTECTION: Eye protective measures are normally necessary, and are suggested when using
this product. Consult AS1336 and AS/NZ1337.
PROTECTIVE GLOVES: Rubber, PVC or other protective gloves are necessary, and desirable, especially if
this product is being used frequently or for lengthy periods. Consult AS2161 for
guidance.
CLOTHING: Clean overalls should be worn, preferably with an apron. Consult AS2919 for
clothing guidance.
SAFETY FOOTWEAR: Wearing safety boots is advisory. Consult AS/NZ2210 for advice on Occupational
Protective Footwear.
Material Safety Data Sheet 鈥? Resiloc HB Base 鈥? Page 2 of 4 鈥? 1st March 2008
MATERIAL SAFETY DATA SHEET 鈥? PAGE 3 OF 4
Section 9 鈥? Physical and Chemical Properties
APPEARANCE (COLOUR, PHYSICAL FORM, SHAPE):
Off white, soft paste
ODOUR: Nil
SOLUBILITY: Insoluble
VAPOUR DENSITY: Not available VAPOUR PRESSURE: Negligible
MELTING POINT: Not applicable BOILING POINT: Not available
FREEZING POINT: Not available SPECIFIC GRAVITY: 0.8 鈥? 1.0
FLASH POINT: > 93掳C UPPER FLAMMABLE LIMIT: Not established
LOWER FLAMMABLE LIMIT: Not established AUTOIGNITION TEMPERATURE:Unknown
VOLATILE ORGANIC COMPOUNDS (VOC) CONTENT: Nil.
Section 10 鈥? Stability and Reactivity
CHEMICAL STABILITY: Stable
CONDITIONS TO AVOID: Keep away from strong acids, bases and oxidising agents.
INCOMPATIBLE MATERIALS: No restrictions
HAZARDOUS DECOMPOSITION PRODUCTS:
On burning may emit toxic fumes, including carbon and nitrogen oxides.
HAZARDOUS REACTIONS: None
Section 11 鈥? Toxicological Information
TOXICOLOGY INFORMATION: No toxicity data is available for this product.
HEALTH EFFECTS FROM THE LIKELY ROUTES OF EXPOSURE:
INHALATION: Not normally a hazard at normal temperatures, however at elevated
temperatures vapour may be irritating to respiratory system. Inhalation of
vapour may result in nausea and headache.
INGESTION: Swallowing may result in nausea, vomiting, abdominal pain and diarrhoea.
SKIN: Is irritating and may cause drying of the skin. May lead to dermatitis and in some
cases sensitisation. The material may accentuate pre-existing skin conditions.
EYES: Irritating and abrasive to the eyes and is capable of causing temporary
impairment of vision, eye inflammation and ulceration.
CHRONIC EFFECTS: May causes sensitisation in susceptible individuals by skin contact. Repeated or
prolonged skin contact may result in allergic contact dermatitis.
Section 12 鈥? Ecological Information
ECOTOXICITY: Not available
PERSISTENCE AND DEGRADABILITY:
Not available
MOBILITY: Not available
ENVIRONMENTAL PROTECTION:
Product is toxic to aquatic organisms, and may cause long-term adverse effects
in the aquatic environment. Avoid contaminating waterways.
Section 13 鈥? Disposal Considerations
DISPOSAL METHODS AND CONTAINERS:
Refer to State Land Waste Management Authority. Empty containers must be
decontaminated. Normally suitable for disposal at approved land waste site.
Section 14 鈥? Transport Information
This material is a Class 9 鈥? Miscellaneous Dangerous Good according to the Australian Code for the Transport of
Dangerous Goods by Road and Rail. Class 9 Goods are incompatible in a placard load with dangerous goods of Class
1, Explosives.
UN NUMBER: None assigned
UN PROPER SHIPPING NAME: None assigned
DANGEROUS GOODS CLASS: None assigned
SUBSIDIARY RISK: None assigned
PACKING GROUP: None assigned
SPECIAL PRECAUTIONS PER USER:
Keep containers tightly sealed, store in a cool, dry, well ventilated place out of
direct sunlight. Keep away from strong acids, bases and oxidising agents.
HAZCHEM CODE: None assigned
Material Safety Data Sheet 鈥? Resiloc HB Base 鈥? Page 3 of 4 鈥? 1st March 2008
MATERIAL SAFETY DATA SHEET 鈥? PAGE 4 OF 4
Section 15 鈥? Regulatory Information
POISON SCHEDULE: S5
OHS: Unregulated
ENVIRONMENTAL: Unregulated
ADDITIONAL NATIONAL AND/OR INTERNATIONAL REGULATORY INFORMATION:
Unregulated
Section 16 鈥? Other Information
DATE OF PREPARATION OR LAST REVISION OF MSDS:
1st March 2008
CONTACT POINT: Aitken Freeman Pty Ltd
(03) 9701 3955
LITERATURE REFERENCES / SOURCES OF DATA:
Material Safety Data Sheets from Suppliers
List of Designated Substances 鈥? Worksafe Australia (on-line)
Australian Dangerous Goods Code 6th Edition
Standard for the Uniform Scheduling of Drugs and Poisons No 19
The information presented herein has been compiled from sources considered to be dependable and is accurate to
the best of seller's knowledge, however seller makes no warranty whatsoever, expressed, implied, or of
merchantability regarding to the accuracy of such data or the results to be obtained from the use thereof. Seller
assumes no responsbility for injury to the buyer or third persons or for any damage to property. Buyer assumes all
risks.
Material Safety Data Sheet 鈥? Resiloc HB Base 鈥? Page 4 of 4 鈥? 1st March 2008
Aitken Freeman Pty Ltd
Factory 7, 7-9 Brough St, Springvale VIC 3171
PO Box 548, Noble Park VIC 3174
Phone: (03) 9701 3955 Fax: (03) 9701 3956
Internet: www.aitkenfreeman.com
e-mail: sales@aitkenfreeman.com
MATERIAL SAFETY DATA SHEET 鈥? PAGE 1 OF 4
RESILOC HB HARDENER
This product is classified as hazardous according to criteria of NOHSC
Section 1 鈥? Identification of the Material and Supplier
PRODUCT (MATERIAL) NAME: RESILOC HB HARDENER
OTHER NAMES:
RECOMMENDED USES: Hardener component of two part epoxy repair mortar system
SUPPLIER NAME/ADDRESS: Aitken Freeman Pty Ltd 鈥? Factory 7, 7-9 Brough St, Springvale VIC 3171
TELEPHONE NUMBER: (03) 9701 3955 FACSIMILE NUMBER: (03) 9701 3956
EMERGENCY PHONE NUMBER: (03) 9701 3955 HOURS: 0800-1700 Mon-Fri
Section 2 鈥? Hazards Identification
HAZARD CLASSIFICATION: Classified as a HAZARDOUS SUBSTANCE according to criteria of NOHSC.
Classified as DANGEROUS GOODS according to criteria of ADG Code.
RISK PHRASES: R20/21/22: Harmful by inhalation, in contact with skin and if swallowed.
R34: Causes burns
R42/43: May cause sensitisation by inhalation or skin contact.
R51/53: Toxic to aquatic organisms, may cause long-term adverse effects in the
aquatic environment.
SAFETY PHRASES: S24/25: Avoid contact with the skin and eyes.
S26: In case of contact with eyes, rinse immediately with plenty of water and
contact a doctor or Poisons Information Centre on 13 11 26 (Australia-wide).
S28: After contact with skin, wash immediately with water (and soap if available)
S36/37/39: Wear suitable protective clothing, gloves and eye/face protection.
S61: Avoid release to the environment.
Section 3 鈥? Composition / Information on Ingredients
INGREDIENTS:
Chemical Name: Proportion: CAS Number:
Isophoronediamine 10 鈥? 30 % [2855-13-2]
Benzyl alcohol 30 鈥? 60 % [100-51-6]
N-aminoethylpiperazine 1 鈥? 10 % [140-31-8]
Triethylenetetramine 10 鈥? 30 % [112-24-3]
Balance of formulation consists of ingredients below cut-off rates or ingredients determined not to be hazardous.
Section 4 鈥? First Aid Measures
INHALATION: If inhaled, remove patient from contaminated area to fresh air 鈥? avoid becoming
a casualty. Remove contaminated clothing and loosen remaining clothing. Lay
patient down in a comfortable position, keep warm and rested. Seek medical
attention if further symptoms develop. If not breathing, clear airway and apply
artificial respiration.
INGESTION: If swallowed, DO NOT induce vomiting. Rinse mouth with plenty of water. Seek
immediate medical advice from a doctor or the Poisons Information Centre
(13 11 26 Australia-wide).
SKIN: If skin or hair contact occurs, remove all contaminated clothing and wash before
reuse. Flush skin and/or hair with running water and soap if available. Seek
medical assistance if irritation persists.
EYES: If product comes into contact with eyes, hold eyelids apart and flush the eye
continuously with fresh running water. If pain persists or recurs seek medical
attention. Removal of contact lenses after an eye injury should only be
undertaken by skilled personnel.
FIRST AID FACILITIES: Eye wash and normal washroom facilities.
ADVICE TO DOCTOR: Treat symptomatically. POISON INFORMATION CENTRE 鈥? 13 11 26 Australia-
wide. This product is corrosive.
Material Safety Data Sheet 鈥? Resiloc HB Hardener 鈥? Page 1 of 4 鈥? 1st March 2008
MATERIAL SAFETY DATA SHEET 鈥? PAGE 2 OF 4
Section 5 鈥? Fire Fighting Measures
EXTINGUISHING MEDIA: Water mist CO2, foam or dry powder.
HAZARDS FROM COMBUSTION PRODUCTS:
Combustion may release toxic fumes, including carbon monoxide, amines,
ammonia, and nitrogen oxides.
SPECIAL PROTECTIVE PRECAUTIONS AND EQUIPMENT FOR FIRE FIGHTERS:
Heating can cause expansion or decompostion leading to violent rupture of
containers. Keep containers cool with water spray. Fire fighters should wear self
contained breathing apparatus if risk of exposure to vapour or products of
combustion. Avoid bodily contact with substance or run off.
SPECIFIC HAZARDS: Liquid and vapour are flammable. Vapour forms an explosive mixture with air.
Section 6 鈥? Accidental Release Measures
EMERGENCY PROCEDURES: Product is slippery when spilt 鈥? avoid accidents by cleaning up any spills
immediately. Wear gloves, protective goggles and appropriate protective
equipment to avoid eye and skin contact. Isolate and contain spill and soak up
with inert material such as clay or sand. Prevent by any means possible the
material from entering storm water drains, waterways, basements or workpits.
Collect in suitable containers and ensure these are correctly labelled. Ensure area
is thoroughly ventilated before recommencing work.
METHODS AND MATERIALS FOR CONTAINMENT AND CLEAN UP:
Contain and collect spills as detailed above. Refer to State Land Waste
Management Authority for disposal considerations.
Section 7 鈥? Handling and Storage
PRECAUTIONS FOR SAFE HANDLING:
Wear protective goggles or face shield and rubber gloves and barrier cream to
prevent eye and skin contamination. Contact lenses pose a special hazard as they
may absorb irritants. Suitable protective clothing, PVC gloves and boots should
be worn. Use in a well ventilated area, preferably outdoors. General exhaust is
normally adequate. If risk of overexposure exists, wear SAA approved dust
respirator.
CONDITIONS FOR SAFE STORAGE:
Store in accordance with AS 3780-1994: The storage and handling of corrosive
substances; and AS1940: The storage and handling of flammable and
combustible liquids.
STORAGE: Store in a cool, dry, well-ventilated area out of direct sunlight. Store away from
strong acids and oxidising agents.
INCOMPATIBILITIES: No restrictions.
Section 8 鈥? Exposure Controls / Personal Protection
NATIONAL EXPOSURE STANDARDS:
No exposure standards have been established for this product by NOHSC. No
exposure limits have been established for individual constituents.
BIOLOGICAL LIMIT VALUES: Not established for the product.
ENGINEERING CONTROLS: If used in limited ventilation, ensure adequate ventilation to maintaine exposure
levels are kept below standards, by using a local exhaust. Keep containers closed
when not in use.
PERSONAL PROTECTION: Avoid unnecessary contact as good work practice. Wash contaminated clothing
and protective equipment before storing and reuse. Wash hands before eating,
smoking, or using the toilet.
RESPIRATORY PROTECTION: It is usually safe not to use respiratory protection. However, where engineering
controls are not effective in controlling airborne exposure, the use of a mask or
other device is appropriate. For assistance in selecting suitable equipment consult
AS/NZ1715.
EYE PROTECTION: Eye protective measures are normally necessary, and are suggested when using
this product. Consult AS1336 and AS/NZ1337.
PROTECTIVE GLOVES: Rubber, PVC or other protective gloves are necessary, and desirable, especially if
this product is being used frequently or for lengthy periods. Consult AS2161 for
guidance.
CLOTHING: Clean overalls should be worn, preferably with an apron. Consult AS2919 for
clothing guidance.
SAFETY FOOTWEAR: Wearing safety boots is advisory. Consult AS/NZ2210 for advice on Occupational
Protective Footwear.
Material Safety Data Sheet 鈥? Resiloc HB Hardener 鈥? Page 2 of 4 鈥? 1st March 2008
MATERIAL SAFETY DATA SHEET 鈥? PAGE 3 OF 4
Section 9 鈥? Physical and Chemical Properties
APPEARANCE (COLOUR, PHYSICAL FORM, SHAPE):
Clear liquid
ODOUR: Strong amine odour
SOLUBILITY: Insoluble
VAPOUR DENSITY: Not available VAPOUR PRESSURE: Negligible
MELTING POINT: Not applicable BOILING POINT: Not available
FREEZING POINT: Not available SPECIFIC GRAVITY: 0.98
FLASH POINT: > 62掳C UPPER FLAMMABLE LIMIT: Not established
LOWER FLAMMABLE LIMIT: Not established AUTOIGNITION TEMPERATURE:Unknown
VOLATILE ORGANIC COMPOUNDS (VOC) CONTENT: Not stated
Section 10 鈥? Stability and Reactivity
CHEMICAL STABILITY: Stable under normal conditions
CONDITIONS TO AVOID: Keep away from strong acids and oxidising agents.
INCOMPATIBLE MATERIALS: No restrictions
HAZARDOUS DECOMPOSITION PRODUCTS:
On burning may emit toxic fumes, including carbon monoxide, amines, ammonia
and nitrogen oxides.
HAZARDOUS REACTIONS: None
Section 11 鈥? Toxicological Information
TOXICOLOGY INFORMATION: No toxicity data is available for this product.
HEALTH EFFECTS FROM THE LIKELY ROUTES OF EXPOSURE:
INHALATION: Vapour or mist is irritating to the upper respiratory tract and may cause
sensitisation. Inhalation of vapour may aggravate pre-existing conditions such as
asthma, bronchitis or emphysema. Acute effects may be chest and nasal irritation
with coughing, sneezing, heacache and nausea. Hazard increases at elevated
temperatures.
INGESTION: Harmful and highly irritating if swallowed. Swallowing may result in nausea,
vomiting, abdominal pain and diarrhoea. May cause chemical burns to the mouth,
throat and oseophagus, with extreme discomfort and pain. Considered an unlikely
route of entry in commercial/industrial environments.
SKIN: Prolonged exposure is highly irritating and may cause drying and cracking of the
skin. Material is corrosive and can cause chemical burns. Capable of causing
dermatitis and sensitisation resulting in hives, rash, itching or swelling of
extremities. Toxic effects may result from skin absorption. Sensitisation may
appear after repeated symptom-free exposures. Open cuts, abraded or irritated
skin should not be exposed to this material. This material may accentuate pre-
existing skin conditions.
EYES: Highly irritating to the eyes and is capable of causing pain and corneal burns. If
not promptly treated, can lead to permanent eye injury.
CHRONIC EFFECTS: May causes sensitisation in susceptible individuals by skin contact or inhalation.
Repeated or prolonged skin contact may result in allergic contact dermatitis.
Section 12 鈥? Ecological Information
ECOTOXICITY: Not available
PERSISTENCE AND DEGRADABILITY:
Not available
MOBILITY: Not available
ENVIRONMENTAL PROTECTION:
Product is toxic to aquatic organisms, and may cause long-term adverse effects
in the aquatic environment. Avoid contaminating waterways.
Section 13 鈥? Disposal Considerations
DISPOSAL METHODS AND CONTAINERS:
Refer to State Land Waste Management Authority. Empty containers must be
decontaminated. Normally suitable for disposal at approved land waste site.
Material Safety Data Sheet 鈥? Resiloc HB Hardener 鈥? Page 3 of 4 鈥? 1st March 2008
MATERIAL SAFETY DATA SHEET 鈥? PAGE 4 OF 4
Section 14 鈥? Transport Information
This material is a Class 8 鈥? Corrosive Substance according to the Australian Code for the Transport of Dangerous
Goods by Road and Rail. Class 8 Goods are incompatible in a placard load with any of the following:
鈼? Class 1, Explosives
鈼? Class 4.3, Dangerous When Wet substances
鈼? Class 5.1, Oxidising Agents and Class 5.2, Organic Peroxides
鈼? Class 6, Toxic Substances (where the toxic substances are cyanides and the corrosives are acids)
鈼? Class 7, Radioactive Substances
鈼? and are incompatible with food and food packaging in any quantity.
UN NUMBER: 1760
UN PROPER SHIPPING NAME: Corrosive Liquids N.O.S.
DANGEROUS GOODS CLASS: 8
SUBSIDIARY RISK: None assigned
PACKING GROUP: III
SPECIAL PRECAUTIONS PER USER:
Keep containers tightly sealed, store in a cool, dry, well ventilated place out of
direct sunlight. Keep away from strong acids and oxidising agents.
HAZCHEM CODE: 3X
Section 15 鈥? Regulatory Information
POISON SCHEDULE: S5
OHS: Unregulated
ENVIRONMENTAL: Unregulated
ADDITIONAL NATIONAL AND/OR INTERNATIONAL REGULATORY INFORMATION:
Unregulated
Section 16 鈥? Other Information
DATE OF PREPARATION OR LAST REVISION OF MSDS:
1st March 2008
CONTACT POINT: Aitken Freeman Pty Ltd
(03) 9701 3955
LITERATURE REFERENCES / SOURCES OF DATA:
Material Safety Data Sheets from Suppliers
List of Designated Substances 鈥? Worksafe Australia (on-line)
Australian Dangerous Goods Code 6th Edition
Standard for the Uniform Scheduling of Drugs and Poisons No 19
The information presented herein has been compiled from sources considered to be dependable and is accurate to
the best of seller's knowledge, however seller makes no warranty whatsoever, expressed, implied, or of
merchantability regarding to the accuracy of such data or the results to be obtained from the use thereof. Seller
assumes no responsbility for injury to the buyer or third persons or for any damage to property. Buyer assumes all
risks.
Material Safety Data Sheet 鈥? Resiloc HB Hardener 鈥? Page 4 of 4 鈥? 1st March 2008
|