MATERIAL SAFETY DATA SHEET
SECTION 1 - PRODUCT IDENTIFICATION AND USE
IDO Heavy Duty Extended Life Diesel Coolant
Product Name:
Permanent antifreeze/Summer Coolant.
Product Class:
Class D2B - Toxic Material
WHMIS Classification:
Irving Oil (506) 632-2000
Supplier Name and Address: Phone:
10 Sydney Street (506) 648-3060
Emergency:
Saint John, N.B.
E2L 4K1
SECTION 2 - HAZARDOUS INGREDIENTS OF MATERIALS
Hazardous Ingredients CAS# wt% ACGIH-TLV LC50 LD50
Ethylene Glycol 107-21-1 90-98 Ceil: 100 ppm Oral: 4700 mg/kg (Rat)
from ACGIH Skin: 9530 mg/kg (Rabbit)
(Canada 1999)
Sodium Benzoate 532-32-1 1-5 Not Available
SECTION 3 - PHYSICAL DATA AND CHEMICAL PROPERTIES
o
Liquid. 2.1
Form: Vapour Pressure(@20 C):
Yellow 2.1
Colour: Vapour Density (Air = 1):
o
N/A. - 13C (8.6F)
Odour: Freezing Point ( C):
o o
1.115-1.145 197 C (386.6F)
Specific Gravity @ 15 C: Boiling Point ( C @760 mm Hg):
Complete <1
Solubility in Water: Evaporation Rate:
N/A
Volatile content (%vol):
SECTION 4 - FIRE AND EXPLOSION HAZARD
Flammability: 鈱es Open flame above flash point.
No Conditions:
Flash Point : cc-116.1C (241F)
15.3% (calculated) 3.2%
Upper Flammable Limit: Lower Flammable Limit:
Not applicable. Not classified.
Auto Ignition Temperature: TDG Flammability Classification:
Not established. Not established.
Sensitivity to Impact: Sensitivity to Static Discharge:
Water, fog, Carbon dioxide, dry chemical, or alcohol foam.
Means of Extinction:
Oxides of carbon.
Hazardous Combustion Products:
Wear self-contained breathing apparatus when fighting fire. Use water to cool fire-exposed
Special Procedures:
containers. A solid stream of water directed into hot burning liquid can cause frothing.
SECTION 5 - REACTIVITY DATA
This product is stable.
Stability:
Will not occur.
Hazardous Polymerisation:
Excessive heat.
Conditions to avoid:
Strong oxidising agents.
Incompatibility with other substances:
Thermal decomposition; oxides of carbon.
Hazardous decomposition products:
The information contained in this form is based on data from sources considered to be reliable but Irving Oil does not guarantee the accuracy or completeness thereof. The information is
provided as a service to the persons purchasing or using the material to which it refers and Irving Oil expressly disclaims all liability for loss or damage including consequential loss or for
injury to persons including death. The information shall not be reproduced, published or distributed in any manner without prior consent in writing of Irving Oil
extended life antifreeze.DOC
Page 1 of 2
MATERIAL SAFETY DATA SHEET
SECTION 6 - TOXICOLOGICAL PROPERTIES
鈱ye 鈱? Ingestion
Route of Entry: Skin Contact Skin Absorption Inhalation
Irritating to eyes and skin. Inhalation irritates nose and throat. High vapour concentration causes
Effects of Acute Exposure:
nausea, vomiting and headaches. Exposure to high concentration from heated antifreeze coolant or
exposure to mists may produce nausea, vomiting, headache, dizziness and irregular eye movements.
Ingestion causes abdominal discomfort or pain, dizziness, lumbar pain, oliguria, uraemia and central
nervous system depression. Ingestion of large volumes cause kidney damage and can be fatal.
Slightly toxic on prolonged or repeated skin contact.
Effects of Chronic Exposure:
50 ppm (vapour or mist) Not determined.
Exposure Limits: Carcinogenicity:
Not determined. Not determined.
Reproductive Toxicity: Teratogenicity:
Irritation to eyes and skin may occur. Not determined.
Irritancy of Product: Mutagenicity:
SECTION 7 - PREVENTATIVE AND CORRECTIVE MEASURES
Gloves: Gloves (impervious).
Personal Protective Equipment:
Eye: Splash Goggles
Respiratory: Wear appropriate respirator when ventilation is inadequate
Footwear: No special requirements under normal conditions.
Clothing: No special requirements under normal conditions. Wear chemical resistant
pants and jacket if in risk of skin exposure.
Other:
Provide adequate ventilation, mechanical or other.
Engineering Controls:
Contain spills with dikes or absorbent material. Prevent from entering sewers or water courses. Clean
Leak and Spill Procedure:
up or absorb for salvage or disposal.
Consult local authorities.
Waste Disposal:
Keep containers closed.
Storage Requirements
None.
Special Shipping Information:
SECTION 8 - FIRST AID MEASURES
Remove to fresh air or give artificial respiration. If breathing is difficult, give oxygen and seek medical attention.
Inhalation:
Give two glasses of water or milk if conscious, then induce vomiting. Seek medical attention immediately.
Ingestion:
Flush with water for 15 minutes.
Eye:
Wash contaminated area with soap and water. Clean contaminated clothing before wearing again.
Skin:
Follow good work/hygiene practices.
General Advice:
SECTION 9 - PREPARATION DATE OF MSDS
Irving Lubricants (506) 632-7000
MSDS Prepared by: Phone:
MSDS Date: February 14, 2007
Revision 03
The information contained in this form is based on data from sources considered to be reliable but Irving Oil does not guarantee the accuracy or completeness thereof. The information is
provided as a service to the persons purchasing or using the material to which it refers and Irving Oil expressly disclaims all liability for loss or damage including consequential loss or for
injury to persons including death. The information shall not be reproduced, published or distributed in any manner without prior consent in writing of Irving Oil
extended life antifreeze.DOC
Page 2 of 2
|