**** SECTION 2 - COMPOSITION, INFORMATION ON INGREDIENTS ****
+----------------+--------------------------------------+----------+-----------+
| CAS# | Chemical Name | % | EINECS# |
|----------------|--------------------------------------|----------|-----------|
| 4165-57-5 |Bromobenzene-d5 | | 224-013-8 |
+----------------+--------------------------------------+----------+-----------+
Hazard Symbols: XI N
Risk Phrases: 10 38 51/53
**** SECTION 3 - HAZARDS IDENTIFICATION ****
EMERGENCY OVERVIEW
Flammable. Irritating to skin. Toxic to aquatic organisms, may cause
long-term adverse effects in the aquatic environment.Hygroscopic
(absorbs moisture from the air).
Potential Health Effects
Eye:
May cause eye irritation.
Skin:
Causes skin irritation.
Ingestion:
The toxicological properties of this substance have not been fully
investigated.
Inhalation:
May cause respiratory tract irritation. Vapors may cause dizziness
or suffocation.
Chronic:
Not available.
**** SECTION 4 - FIRST AID MEASURES ****
Eyes:
Flush eyes with plenty of water for at least 15 minutes,
occasionally lifting the upper and lower eyelids. Immediately flush
eyes with plenty of water for at least 15 minutes, occasionally
lifting the upper and lower eyelids. Get medical aid immediately.
Skin:
Get medical aid. Flush skin with plenty of water for at least 15
minutes while removing contaminated clothing and shoes. Remove
contaminated clothing and shoes.
Ingestion:
If victim is conscious and alert, give 2-4 cupfuls of milk or water.
Get medical aid immediately. Do NOT induce vomiting. If conscious and
alert, rinse mouth and drink 2-4 cupfuls of milk or water.
Inhalation:
Get medical aid immediately. Remove from exposure and move to fresh
air immediately. If not breathing, give artificial respiration. If
breathing is difficult, give oxygen.
Notes to Physician:
**** SECTION 5 - FIRE FIGHTING MEASURES ****
General Information:
As in any fire, wear a self-contained breathing apparatus in
pressure-demand, MSHA/NIOSH (approved or equivalent), and full
protective gear. Vapors may form an explosive mixture with air.
Vapors can travel to a source of ignition and flash back. Will burn
if involved in a fire. Use water spray to keep fire-exposed
containers cool. Containers may explode in the heat of a fire.
Flammable liquid and vapor.
Extinguishing Media:
For small fires, use dry chemical, carbon dioxide, water spray or
alcohol-resistant foam. For large fires, use water spray, fog, or
alcohol-resistant foam. In case of fire, use water, dry chemical,
chemical foam, or alcohol-resistant foam. Use water spray to cool
fire-exposed containers. Water may be ineffective. Use agent most
appropriate to extinguish fire. Do NOT use straight streams of
water.
**** SECTION 6 - ACCIDENTAL RELEASE MEASURES ****
General Information: Use proper personal protective equipment as indicated
in Section 8.
Spills/Leaks:
Absorb spill with inert material (e.g. vermiculite, sand or earth),
then place in suitable container. Clean up spills immediately,
observing precautions in the Protective Equipment section. Remove all
sources of ignition. Use a spark-proof tool. A vapor suppressing foam
may be used to reduce vapors.
**** SECTION 7 - HANDLING and STORAGE ****
Handling:
Ground and bond containers when transferring material. Use
spark-proof tools and explosion proof equipment. Avoid breathing
dust, vapor, mist, or gas. Avoid contact with eyes, skin, and
clothing. Empty containers retain product residue, (liquid and/or
vapor), and can be dangerous. Keep away from heat, sparks and flame.
Do not pressurize, cut, weld, braze, solder, drill, grind, or expose
empty containers to heat, sparks or open flames.
Storage:
Keep away from heat, sparks, and flame. Keep away from sources of
ignition. Store in a cool, dry place. Store in a tightly closed
container. Flammables-area.
**** SECTION 8 - EXPOSURE CONTROLS, PERSONAL PROTECTION ****
Engineering Controls:
Use adequate general or local exhaust ventilation to keep airborne
concentrations below the permissible exposure limits. Use process
enclosure, local exhaust ventilation, or other engineering controls
to control airborne levels.
Exposure Limits
CAS# 4165-57-5:
Personal Protective Equipment
Eyes:
Wear chemical splash goggles. Wear safety glasses and
chemical goggles if splashing is possible.
Skin:
Wear appropriate protective gloves and clothing to
prevent skin exposure. Wear appropriate protective
gloves to prevent skin exposure.
Clothing:
Wear appropriate protective clothing to minimize
contact with skin.
Respirators:
A respiratory protection program that meets OSHA's 29
CFR 1910.134 and ANSI Z88.2 requirements or European
Standard EN 149 must be followed whenever workplace
conditions warrant a respirator's use. Wear a
NIOSH/MSHA or European Standard EN 149 approved
full-facepiece airline respirator in the positive
pressure mode with emergency escape provisions.
**** SECTION 9 - PHYSICAL AND CHEMICAL PROPERTIES ****
Physical State: Clear liquid
Color: colorless
Odor: Not available.
pH: Not available.
Vapor Pressure: Not available.
Viscosity: Not available.
Boiling Point: 53 deg C @ 23.00m
Freezing/Melting Point: Not available.
Autoignition Temperature: Not available.
Flash Point: 51 deg C ( 123.80 deg F)
Explosion Limits, lower: Not available.
Explosion Limits, upper: Not available.
Decomposition Temperature:
Solubility in water: practically insoluble
Specific Gravity/Density: 1.5500g/cm3
Molecular Formula: C6D5Br
Molecular Weight: 162.06
**** SECTION 10 - STABILITY AND REACTIVITY ****
Chemical Stability:
Stable under normal temperatures and pressures.
Conditions to Avoid:
Incompatible materials, ignition sources, excess heat, strong
oxidants.
Incompatibilities with Other Materials:
Strong oxidizing agents.
Hazardous Decomposition Products:
Carbon monoxide, irritating and toxic fumes and gases, carbon
dioxide, hydrogen bromide.
Hazardous Polymerization: Not available.
**** SECTION 11 - TOXICOLOGICAL INFORMATION ****
RTECS#:
CAS# 4165-57-5 unlisted.
LD50/LC50:
Not available.
Carcinogenicity:
Bromobenzene-d5 -
Not listed by ACGIH, IARC, or NTP.
**** SECTION 12 - ECOLOGICAL INFORMATION ****
**** SECTION 13 - DISPOSAL CONSIDERATIONS ****
Dispose of in a manner consistent with federal, state, and local regulations.
**** SECTION 14 - TRANSPORT INFORMATION ****
IATA
Shipping Name: BROMOBENZENE
Hazard Class: 3
UN Number: 2514
Packing Group: III
IMO
Shipping Name: BROMOBENZENE
Hazard Class: 3.3
UN Number: 2514
Packing Group: III
RID/ADR
Shipping Name: BROMOBENZENE
Hazard Class: 3
UN Number: 2514
Packing group: III
**** SECTION 15 - REGULATORY INFORMATION ****
European/International Regulations
European Labeling in Accordance with EC Directives
Hazard Symbols: XI N
Risk Phrases:
R 10 Flammable.
R 38 Irritating to skin.
R 51/53 Toxic to aquatic organisms, may cause
long-term adverse effects in the aquatic environment.
Safety Phrases:
S 9 Keep container in a well-ventilated place.
S 16 Keep away from sources of ignition - No
smoking.
S 33 Take precautionary measures against static
discharges.
S 61 Avoid release to the environment. Refer to
special instructions/safety data sheets.
WGK (Water Danger/Protection)
CAS# 4165-57-5: No information available.
Canada
None of the chemicals in this product are listed on the DSL/NDSL list.
CAS# 4165-57-5 is not listed on Canada's Ingredient Disclosure List.
US FEDERAL
TSCA
CAS# 4165-57-5 is not listed on the TSCA inventory.
It is for research and development use only.
**** SECTION 16 - ADDITIONAL INFORMATION ****
MSDS Creation Date: 5/11/1999 Revision #2 Date: 3/18/2003
The information above is believed to be accurate and represents the best
information currently available to us. However, we make no warranty of
merchantability or any other warranty, express or implied, with respect to
such information, and we assume no liability resulting from its use. Users
should make their own investigations to determine the suitability of the
information for their particular purposes. In no way shall the company be
liable for any claims, losses, or damages of any third party or for lost
profits or any special, indirect, incidental, consequential or exemplary
damages, howsoever arising, even if the company has been advised of
the possibility of such damages.
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
|
|
|
| ALL MSDS PAGES IN THIS GROUP
| | NAME | CAS |
|
Octakis-6-Bromo-6-Deoxy-??5-Cyclodextrin
| 53784-84-2 |
|
Octakis-6-Iodo-6-Deoxy-??5-Cyclodextrin
| 168296-33-1 |
|
4-Chromanol 96%
| 1481-93-2 |
|
Octakis-6-(Dimethyl-Tert-Butylsilyl)-6-Deoxy-??5-Cyclodextrin
| 0-01-1 |
|
Diphenyl phthalate
| 84-62-8 |
|
DL-4-Chlorophenylalanine Methyl Ester Hydrochloride, 99%
| 14173-40-1 |
|
1H-Benzotriazole, 98%
| 95-14-7 |
|
m-Cresol, 95%
| 108-39-4 |
|
Thiodiglycolic Acid,98%
| 123-93-3 |
|
n-Acetyl-s-(2-hydroxyethyl)-l-cysteine
| 15060-26-1 |
|
Methyl 4-(3-Oxo-3-Phenyl-1-Propenyl) Benzoate, 98+% (NMR)
| 98258-72-1 |
|
Barium oxide
| 1304-28-5 |
|
Zinc Sulfide, Pieces, 3-12 mm, 99.9%
| 1314-98-3 |
|
Bromobenzene-d5, 99.5 atom% D
| 4165-57-5 |
|
Toluene-d8, 99.5+ atom % D
| 2037-26-5 |
|
1-Butanol-d10, packaged in ampules, 99+ atom % D
| 71-36-3 |
|
Ethylbenzene-d10, packaged in ampules, 99+ atom% D
| 25837-05-2 |
|
Mesitylene-d12, packaged in ampule, 98 atom% D
| 69441-16-3 |
|
Methylcyclohexane-d14, packaged in ampules, 99 atom % D
| 108-87-2 |
|
Methyl-d3 methacrylate-d5, stabilized
| 80-62-6 |
|
Aniline-d7, 99 atom% D
| 4165-61-1 |
|
Benzyl chloroformate, 50 wt% solution in toluene
| 108-88-3 |
|
Nitrobenzene-D5, 99.5 Atom% D
| 4165-60-0 |
|
1,1,2,2-Tetrachloroethane-d2, 99.5+ atom% D
| 33685-54-0 |
|
4,4'-Ethylenedianiline, 95%
| 621-95-4 |
|
Bromoform-d, stabilized with copper, 99 atom% D
| 75-25-2 |
|
1,2-Bis(dichlorophosphino)ethane, 97%
| 28240-69-9 |
|
N-Benzyl-4-cyano-4-(1-piperidino)-piperidine
| 84254-97-7 |
|
1,3,6,8-Pyrenetetrasulfonic Acid Tetrasodium Salt, 85+% (UV-VIS)
| 59572-10-0 |
|
Dittmer reagent, 95%
| |
|
Isoquinoline, 97%
| 119-65-3 |
|
Alkylbenzene sulfonic acid, mixture of C10-C13 isomers
| |
|
Methyltriallylsilane
| 1112-91-0 |
|
Tetraallylsilane
| 1112-66-9 |
|
2-Ethoxy-2-(2'-phenylsulfonylethyl)-1,3-dioxolane
| 149099-23-0 |
|
Sodium Hydride, Dispersion in Mineral Oil, 75%
| 7646-69-7 |
|
Hexaphenyldisilane
| 1450-23-3 |
|
Citronellal (pract), 93% (gc)
| 106-23-0 |
|
Hydriodic Acid, 57 Wt.% Aq. Solution, Distilled, Unstabilized
| 7732-18-5 |
|
Cyclopentylamine, 99+%
| 1003-03-8 |
|
(Bromomethyl)triphenylphosphonium bromide, 98%
| 1034-49-7 |
|
Methyl trans-3-methoxyacrylate, 95%
| 5788-17-0 |
|
Benzyltriphenylphosphonium borohydride, 98%
| 18117-29-8 |
|
2-Methyl-6-phenylbenzothiazole, 97%
| 107559-02-4 |
|
Ethylenediaminetetraacetic acid ferric sodium salt, trihydrate, 98%
| 15708-41-5 |
|
2,4-Dichlorobenzyl Alcohol, 99%
| 1777-82-8 |
|
Diethyldithiocarbamic Acid Diethylammonium Salt, 98% (Titr.)
| 1518-58-7 |
|
Hydriodic acid, reagent ACS, 55% in water, without stabilizer
| 10034-85-2 |
|
2,2,6,6-Tetramethyl-4-Piperidone Hydrochloride, 97%
| 33973-59-0 |
|
Cellulose Acetate Hydrogen Phthalate, Acetyl Content 17.0-22.0%
| 9004-38-0 |
|
|