CHEMICAL INTERNATIONAL
MATERIAL SAFETY DATA SHEET
EMERGENCY#: CANUTEC (613)996-6666
PRODUCT IDENTIFICATION AND PREPARATION INFORMATION
PRODUCT NAME: C.I. Slip Not EFFECTIVE DATE: 10 September 2003
WHMIS CLASS: Class A, Class B-Div.5, Class D-Div.2B
T.D.G. CLASSIFICATION: Consumer Commodity
CHEMICAL FAMILY: N/A MATERIAL USE: Slip Resistant Epoxy Coating
HAZARDOUS INGREDIENTS
INGREDIENTS CAS # Wt% TWA-TLV LC50 LD50
Acetone 67-64-1 20-40 1000ppm TWA N/A N/A
Xylene 1330-20-7 10-20 150ppm TWA N/A N/A
Toluene 108-88-3 10-20 100 ppm TWA 8000ppm rat 4hr. 2500mg/kg oral rat
Clay (Dust Hazard) 1332-58-7 0-10 N/A N/A N/A
Titanium Oxide 13463-67-7 0-10 N/A N/A N/A
(Dust Hazard)
Amorphous Silica 7631-86-9 0-10 N/A N/A N/A
(Dust Hazard)
Liquefied Petroleum Gas 68476-85-7 20-40 1000ppm TWA N/A N/A
PHYSICAL DATA
BOILING POINT(oF): -232 COEF. OF WATER/OIL DIST.:
VAPOUR PRESSURE (psig @75oF): 65 SPECIFIC GRAVITY (H20=1): 0.800@ 75oF
VAPOUR DENSITY (Air=1): >1 PERCENT VOLATILE (by vol.):
SOLUBILITY IN WATER: Spray mist is insoluble. EVAPORATION RATE (H20=1):
PHYSICAL STATE: ODOUR THRESHOLD:
FREEZING POINT(oF): -13
pH (as supplied): N/A
APPEARANCE AND ODOUR: Aerosol mist, strong solvent odour.
FIRE AND EXPLOSION DATA
FLAMMABILITY: Flammable Spray
FLASH POINT (Deg F method): 45.0 (T.O.C)
HAZARDOUS COMBUSTION PRODUCTS:
MEANS OF EXTINCTION: Foam, carbon dioxide, dry media.
SPECIAL FIRE FIGHTING PROCEDURES: Hazardous decomposition products may form from incomplete
combustion. Wear full protective clothing and self contained positive pressure breathing apparatus.
FIRE AND EXPLOSION HAZARDS: Extremely flammable liquid and vapours. Container can build pressure from
heat and rupture explosively. Volatile vapours can burn in the open, or explode if confined. Vapour is heavy and can
travel long distances to source of ignition.
REACTIVITY DATA
CONDITIONS FOR CHEMICAL INSTABILITY: Stable Hazardous polymerization will not occur
INCOMPATIBILITY: Avoid contact with strong oxidizing agents, alkaline, magnesium, aluminum, and reactive metals.
HAZARDOUS DECOMPOSITION PRODUCTS: Carbon dioxides, carbon monoxides.
FIRST AID
EYE: Flush with large amounts of cool running water for at least 15 minutes while holding upper and lower lids open. if irritation persists, get
medical attention immediately.
SKIN: Thoroughly wash exposed area with soap and water. Remove contaminated clothing. Launder contaminated clothing before reuse.
INHALATION: remove to fresh air. If breathing is difficult, administer oxygen. If breathing has stopped, give artificial respiration. Keep
person warm, quiet, and seek medical attention immediately.
INGESTION: Do not induce vomiting. Seek medical attention immediately. Aspiration of material into lungs due to vomiting can cause
chemical pneumontitis which can be fatal. Never give anything by mouth to an unconscious person.
C.I SLIPNOT
TOXICOLOGICAL PROPERTIES
EFFECTS OF CHRONIC EXPOSURE:
EYES&SKIN: Contact with eyes and skin can cause severe irritation, redness, tearing, and blurred vision. Prolonged
or repeated contact will cause defatting of the skin, and dermatitis in some cases. It may cause allergic skin reaction.
INHALATION: Inhalation of mist can cause irritation of nasal and respiratory passages. Repeated or prolonged
exposure to high levels of solvent vapours may cause permanent brain and nervous system damage. May also cause
liver and kidney damage.
INGESTION: Can cause gastrointestinal irritation, nausea, vomiting, and diarrhea. Aspiration of chemical into the
lungs can cause chemical pneumontitis.
CARCINOGENICITY: Non hazardous by WHIMIS criteria.
REPRODUCTIVE TOXIN: Not sufficient data.
TERATOGENICITY: Not sufficient data.
MUTAGENICITY: Not sufficient data
SYNERGISTIC MATERIALS: Not available
PREVENTATIVE MEASURES
GLOVES: Wear protective gloves such as Polyvinyl or Polyethylene.
EYE PROTECTION: Chemical splash goggles in compliance with OSHA regulations are advised.
RESPIRATORY PROTECTION: If workplace exposure limit(s) of product, or any component is exceeded, use a
NIOSH/MSHA approved air supplied respirator. Engineering or or administrative controls should be implemented to
reduce exposure.
ENGINEERING CONTROLS: Provide sufficient mechanical ventilation to keep TLV of section II ingredients
below acceptable limits.
LEAK AND SPILL PROCEDURE: Allow propellant to evaporate. Maintain local exhaust and adequate
ventilation. No smoking.
Keep sparks, heat sources, and open flame far away from spill or leak. Cover with absorbent material and sweep up.
Wash area to prevent slipping.
Dispose of soaked absorbent material in accordance with federal, provincial, and local regulations.
WASTE DISPOSAL: Aerosol cans, when emptied and depressurized through normal use, pose no disposal hazard
and should be recycled.
Consult federal, provincial, and local authorities for approved procedures.
HMIS HAZARD RATING INFORMATION
FLAMMABILITY REACTIVITY HEALTH
4 0 2
DISCLAIMER: Information for this material safety data sheet was obtained from sources considered technically accurate
and reliable. While every effort has been made to ensure full disclosure of product hazards, in some cases, data is not
available and is so stated. Since conditions of actual product use are beyond the control of the supplier, it is assumed
that the user of this material has been full trained according to the mandatory requirements of WHIMIS. No warranty,
expressed or implied is made, and supplier will not be liable for any losses, injuries, or consequential damage which may
result from the use or reliance on any information contained in this form.
CHEMICAL INTERNATIONAL
18043 鈥? 107 Avenue
EDMONTON ALBERTA
T5S 1K3
|