Formosa Plastics Corporation, TexasÂ
Material Safety Data SheetÂ
MANUFACTURERÂ MSDSÂ No:Â C/A009Â
Formosa Plastics Corporation, TexasÂ
201 Formosa Drive, Point Comfort, TX 77978 11/14/2007Â
Preparation Date:Â
02/23/2007Â
Telephone: (361) 9877000 Fax: (361) 9872363 Supersedes Date:Â
Emergency: 800Â424Â9300Â (CHEMTREC)Â
1. PRODUCT IDENTIFICATIONÂ
Ethylene Dichloride (EDC)Â
Product Name:Â
EDCÂ
Product Code:Â
Chlorinated HydrocarbonÂ
Chemical Family:Â
1,2ÂDichloroethaneÂ
Chemical Name:Â
107Â06Â2Â
CASÂ No:Â
Ethylene chloride, EDC, SymÂdichloroethane, Ethane dichloride, 1,2ÂÂ
Synonyms:Â
DichloroethaneÂ
Formula:Â
C2H4Cl2Â
Technical Information: (361) 987Â7453Â
2. PRODUCT INGREDIENTSÂ
No. Components CAS No. Percent (%) OSHA PELÂ
P Ethylene Dichloride 107Â06Â2 99Â100 50 ppm TWAÂ
3. PHYSICAL/CHEMICAL PROPERTIESÂ
LiquidÂ
Physical Form:Â
Clear, colorlessÂ
Color:Â
SweetÂ
Odor:Â
99Â
Molecular Weight:Â
182.3°F (83.5°C)Â
Boiling Point:Â
Â31.54°F (Â35.3°C)Â
Melting Point:Â
Â31.54°F (Â35.3°C)Â
Freezing Point:Â
5Â10 mg/ml @20 degrees CÂ
Solubility in Water:Â
1.26 (water = 1)@ 20 degrees CÂ
Specific Gravity:Â
3.4 (air = 1)Â
Vapor Density:Â
0.27 (Butyl Acetate = 1)Â
Evaporation Rate:Â
60 mg Hg @20 degrees CÂ
Vapor Pressure:Â
100Â
%Â Volatile:Â
About 7Â
pH:Â
The physical data presented above are typical values and should not be construed as a specification.Â
4. FIRE HAZARD DATA AND FIGHTING METHODÂ
55.4°F (13°C)Â
Flash Point:Â
775°F (412.78°C)Â
Autoignition:Â
Flammable LimitsÂ
6.2Â
In Air (LEL, %)Â
15.9Â
(UEL, %)Â
Dry chemical, carbon dioxide, water fog and spray.Â
Extinguishing Media:Â
In the event of a fire, wear NIOSH approved, positive pressure, selfÂcontainedÂ
breathing apparatus (SCBA), and full protective gear. Fight fire from protectedÂ
Special Fire FightingÂ
location or maximum possible distance. Stop flow of gas before extinguishingÂ
Procedure:Â
fire. Immediately evacuate area. Cool exposed equipment with water spray untilÂ
fire is out.
Vapors are heavier than air and may travel along the ground and considerableÂ
Unusual Fire andÂ
distance to a source of ignition and flash back.Â
Explosion Hazards:Â
5. HUMAN HEALTH DATAÂ
This product is toxic by inhalation, ingestion, and skin contact. It may cause narcosisÂÂ
Emergency Overview:Â
like effects, headache, nausea, vomiting and weakness.Â
Primary Route(s) ofÂ
Inhalation, Ingestion, Eye, Skin ContactÂ
Exposure:Â
Potential Health Effects and Symptoms of OverÂExposureÂ
May cause damage to liver, kidney, lung, digestive tract and central nervous system.Â
May cause severe irritation to eyesÂ
Eye Contact:Â
May cause severe irritation to skinÂ
Skin Contact:Â
May cause severe irritation to respiratory tractÂ
Inhalation:Â
May cause severe irritation to digestive tractÂ
Ingestion:Â
Medical Conditions Aggravated by Overexposure:Â
None identifiedÂ
NTP: Yes IARC: Yes OSHA: NoÂ
Carcinogenicity:Â
NTP: Anticipated human carcinogen. IARC Cancer Review: Animal Sufficient Evidence.Â
6. FIRST AID MEASURESÂ
Immediately irrigate with copious amounts of water for at least 15 minutes. Call a physician.Â
Eye Contact:Â
Immediately wash with large quantities of water under emergency safety shower whileÂ
Skin Contact:Â
removing contaminated clothing. Wash affected area with mild soap. Call a physician.Â
Remove to fresh air. Support respiration. Call a physician.Â
Inhalation:Â
If person is conscious give up to 1 pint of water. Do not induce vomiting. Call a physician.Â
Ingestion:Â
Never administer Adrenaline for swallowing or inhalation overÂexposure. IncreasedÂ
sensitivity of heart to Adrenaline may be caused by the overÂexposure. Saline CatharticsÂ
Notes to Physician:Â
should be considered following high dose ingestion. OverÂexposure may cause vomiting andÂ
protracted retching via CNS mechanism.Â
If the victim is convulsing or unconscious, do not give anything by mouth, ensure that theÂ
Other Instructions:Â
victim's airway is open and lay the victim on his/her side with the head lower than the body.Â
7. EXPOSURE CONTROLS, PERSONAL PROTECTIONÂ
RECOMMENDATIONSÂ
Splash proof chemical goggles.Â
Eye Protection:Â
Polyvinyl alcohol or nitrile gloves with 4H liner, boots and protective clothing to preventÂ
Skin Protection:Â
skin contact.Â
NIOSH approved respirators, SCBA.Â
Respiratory Protection:Â
Ventilation Requirements ÂÂ
Local Exhaust, GeneralÂ
Engineering Control:Â
Maintain the ambient workplace atmosphere below the legislated PELs listed in Section 2.Â
Avoid contact with skin and avoid breathing vapor. Do not eat, drink, or smoke in work area.Â
Wash hands thoroughly after handling, especially before eating, drinking, smoking, chewing,Â
Required Work/HygieneÂ
or using restroom facility. Contaminated clothing and shoes should be thoroughly cleanedÂ
Procedure:Â
before reuse or properly disposed of.Â
Exposure Guidelines:Â
No. Components OSHAÂPEL ACGIHÂTLVÂ
P Ethylene Dichloride 50 ppm TWA 10 ppm TWAÂ
8. ACCIDENTAL RELEASE CONTROL MEASURESÂ
Evacuate the area and eliminate ignition sources. Wear full protective clothing and positive,Â
selfÂcontained breathing apparatus. Contain the spill. Remain upwind and dissipate vaporÂ
Response to Spills:Â
with water spray. Increase ventilation if in an enclosed area. Prevent liquid or vapors from
entering sewers or other low areas. Notify appropriate authorities as necessary.Â
9. HANDLING AND STORAGEÂ
When transferring this product, there is potential for static electricity buildup. ConsiderationÂ
should be given to bonding and grounding and venting of equipment during loading,Â
Handling:Â
unloading, and transfer of this product. Do not handle this product near heat, sparks, orÂ
flame.Â
Store in a cool, dry, wellÂventilated area. Keep away from sources of ignition, sparks or openÂ
Storage:Â
flame.Â
Keep containers tightly closed.Â
Container Use:Â
10. STABILITY AND REACTIVITYÂ
StableÂ
Stability:Â
Avoid heat, flame, other sources of ignition. Not compatible with strong oxidizers, strongÂ
Conditions to Avoid:Â
bases, aluminum, magnesium, potassium, sodium, nitric acid and ammonia.Â
HazardousÂ
Hydrogen chloride gas, carbon dioxide, carbon monoxide, and phosgene.Â
Decomposition:Â
Hazardous Polymerization: Will not occur.Â
11. DISPOSAL CONSIDERATIONSÂ
It must be disposed of in accordance with Federal, State and local environmental controlÂ
Disposal Method:Â
regulations.Â
Recycle to process if possible.Â
Recycle/Reclaim:Â
12. TRANSPORT INFORMATIONÂ
Ethylene DichlorideÂ
Proper shipping Name:Â
3Â
DOT Hazard Class:Â
UN1184Â
UN/NAÂ Number:Â
Flammable liquid, PoisonÂ
Hazard Label(s):Â
IIÂ
Packing Group:Â
Emergency Response GuideÂ
129Â
(ERG)Â No.:Â
13. TOXICOLOGICAL INFORMATIONÂ
The information provided below can be subject to misinterpretation. Therefore, it is essential the following information beÂ
interpreted by individuals trained in its evaluation.Â
Chemical Toxicity DataÂ
Skin and Eye Irritation Data:Â
eyeÂrbt: 63 mg SEVÂ
sknÂrbt: 625 mg open MLDÂ
Tumorigenic Data:Â
Ethylene Dichloride TDLo: orlÂrat 5286 mg/kg/69WÂIÂ
TCLo: ihlÂrat 5 ppm/7H/78WÂIÂ
Teratogenicity:Â
TCLo: ihlÂrat 300 ppm/7H (6Â15D preg)Â
14. ECOLOGICAL INFORMATIONÂ
No data available on the adverse effects of this product on the environment. Neither COD or BOD data are available.Â
15. REGULATORY INFORMATIONÂ
FEDERALÂ REGULATORYÂ INFORMATIONÂ
Ethylene DichlorideÂ
PELÂTWAÂ 50Â ppmÂ
OSHAÂ Status:Â
Hazardous Air Pollutants (HAPs) ListingÂ
EPA Clean Air Act Status:Â
ARP Flammable Substances (40 CFR 68.130) ListingÂ
Hazardous Substances Listing (40 CFR 116)Â
EPA Clean Water ActÂ
Priority Pollutants Listing
Status:Â
Toxic Pollutants Listing (40 CFR 401.15; 403 App.B)Â
U.S. INVENTORY (TSCA): All the components of this substance are listed on or areÂ
exempt from the inventory. Subject to a TSCA Section (4) Enforceable Consent Agreement.Â
Formosa Plastics and others are to report as required under Section 12(b). (ETHYLENEÂ
DICHLORIDEÂ 107Â06Â2)Â
TSCAÂ 12(b)Â EXPORTÂ NOTIFICATION:Â
1,1,2ÂTRICHLOROETHANEÂ
TSCAÂ Status:Â
CASÂ NUMBER: 79Â00Â5Â
SECTIONÂ 4Â
1,2ÂDICHLOROETHANEÂ
CASÂ NUMBER: 107Â06Â2Â
SECTIONÂ 4Â
100Â lbs.Â
CERCLAÂ RQ:Â
SARA Title IIIÂ
Ethylene DichlorideÂ
Section 302* Section 313** Section 311/312***Â
None Yes H1, H2, P3Â
*Reportable quantity of extremely hazardous substance, Sec. 302Â
*Threshold planning quantity, extremely hazardous substance, Sec. 302Â
**Toxic chemical. Sec. 313Â
**Category as required by Sec 313 (40CFR372.65C). Must be used on Toxic Release Inventory form.Â
***Hazard category for SARA Sec.311/312 reporting H1=acute health hazard, H2=chronic health hazard, P3=fire hazard,Â
P4=sudden release of pressure hazard, P5=reactive hazardÂ
If disposed of in its purchased form, this product meets the RCRA hazardous waste codeÂ
U077 by listing. Under RCRA, it is the responsibility of the product user to determine at theÂ
RCRAÂ Status:Â
time of disposal whether a material containing the product or derived form the productÂ
should be classified as a hazardous waste (40 CFR 261.20Â24).Â
OTHERÂ REGULATORYÂ INFORMATIONÂ
The following chemicals are specifically listed by individual states; other productÂspecific health and safety data in otherÂ
sections of the MSDS may also be applicable for state requirements. For details on your regulatory requirements, youÂ
should contact the appropriate agency in your state.Â
State Chemical RegulationÂ
Cal Prop. 65 listing.Â
CaliforniaÂ
State RightÂToÂKnow Substances listingÂ
FL; LA; MA; MN; NJ;Â
Ethylene DichlorideÂ
PAÂ
Listed in Texas Air Contaminants with Health Effects ScreeningÂ
TexasÂ
Levels: 40 ppb short term and 1 ppb long term.Â
Product Name: Ethylene DichlorideÂ
InternationalÂ
Australia: Australian Inventory of Chemical Substances (AICS) ListingÂ
Canada: WHMIS: Ingredient disclosure 1% item 715 (498)Â
National Pollutant Release Inventory (NPRI): YesÂ
Domestic Substance List (DSL) Inventory listingÂ
United Kingdom: Maximum Exposure Limits: 7 ppm TWAÂ
Germany: Carcinogens (animal evidence of carcinogenicity)Â
Israel:Â PELÂTWAÂ 10Â ppm
16. OTHER INFORMATIONÂ
NFPAÂ HMISÂ
Fire  3 Health Â 3Â
Health Â 2 Flammability  3Â
Reactivity ÂÂ 0Â Reactivity ÂÂ 1Â
Personal Protection Index  XÂ
Specific Hazard  NoneÂ
X: Ask your supervisor or safety specialist for handling instructions.Â
This information is furnished without warranty, expressed or implied, except that it is accurate to the bestÂ
knowledge of Formosa Plastics Corporation, Texas. Neither Formosa Plastics Corporation, Texas nor any of itsÂ
subsidiaries assume any liability whatsoever for the accuracy or completeness of the information contained herein.Â
Final determination of suitability of any material is the sole responsibility of the user. All materials may presentÂ
unknown hazards and should be used with caution. Although certain hazards are described herein, we cannotÂ
guarantee that these are the only hazards which exist. Formosa Plastics Corporation, Texas assumes no legalÂ
responsibility for loss, damage or expense arising out of, or in any way connected with, the handling, storage, use orÂ
disposal of this product.Â
EHSC Intranet | Procedures | Regulatory Reviews | Communications | EducationÂ
Provide Feedback | Tell a Friend | Copyright Notice | FPC IntranetsÂ
Copyright ©1999 Â2007 FPC USA
|