MSDS - Material Safety Data Sheet
Product Name: Synlube 1711 Aerosol
MSDS No.: 042902
I. Basic Information:
Manufacturer: Synair Corporation
2
DISTRIBUTED BY FREEMAN MFG & SUPPLY CO. 800-321-8511 2 1
Transportation Emergency Phone: Chem-trec 1-800-424-9300
Last Update: 05/13/2002
2
X
Chemical State: Liquid Gas Solid 2
X
Chemical Type: Pure Mixture 1
H
II. Ingredients:
SARA OSHA ACGIH Other
CAS No. Chemical Name % Range EHS NTP IARC SUB Z 313 PEL TLV Limits
811972 1,1,1,2-Tetrafluoroethane 13-16 1000ppm 1000ppm NE
1717006 1,1-Dichloro-1-fluoroethane 59-64 X NE 500 ppm NE
68476857Liquefied Petroleum Gas 14-18 1000ppm 1000ppm NE
Non-Hazardous Release Blend 4-7 NE NE NE
III. Hazardous Identification:
Hazard Category:
Acute X Chronic X Fire Pressure Reactive
X
Hazardous Identification Information:
Warning!
Clear, colorless liquid with a faint ether-like odor.
Incompatible with alkalies and strong oxidizing agents.
Avoid open flames, hot metal surfaces and other high temperature sources.
Repeated contact may cause minor skin and eye irritation.
IV. First Aid Measures:
Route(s) of Entry:
Inhalation, Ingestion, Skin and Eye contact.
Health Hazards (Acute and Chronic):
Acute (Short-Term)
Contact with the liquid may cause dryness of the skin and irritation of the eyes and throat. Inhalation of high concentrations of
vapors may cause dizziness and nausea.
Chronic (Delayed)
Repeated contact may produce minor skin and eye irritation. Blood pressure depression may result from breathing high
Page 2 of 4 Date Printed: 05/14/2002
MSDS - Material Safety Data Sheet
Product Name: Synlube 1711 Aerosol
MSDS No.: 042902
concentrations of vapors. Persons with pre-existing heart disease may be at an increased risk from exposure.
Signs and Symptoms:
Contact may cause minor skin and eye irritation. Inhalation of high concentrations of vapors may cause dizziness and
nausea.
Medical Conditions Generally Aggravated by Exposure:
Blood pressure depression may result from breathing high concentrations of vapors. Persons with pre-existing heart
disease may be at an increased risk of exposure.
Emergency and First Aid Procedures:
SKIN CONTACT: Wash affected area with warm soapy water and apply barrier cream.
EYE CONTACT: Flush eyes with water for at least 15 minutes and contact a physician.
INGESTION: Do NOT induce vomiting. Take 1-2 glasses of water or milk and contact a physician. Do not give anything by
mouth to an unconscious person.
INHALATION: Remove person to fresh air. If person is not breathing give mouth-to-mouth resuscitation and contact a
physician.
Other Health Warnings:
None known
V. Fire Fighting Measures:
Flash Point: NE Lower Explosive Limit: NE Upper Explosive Limit: NE
Fire Extinguishing Media: Foam, water spray, carbon dioxide or dry chemical extinguishers.
Special Fire Fighting Procedures:
Firefighters should wear a self-contained breathing apparatus and protective clothing to guard against incompletely
combusted carbon products and halogenated solvents.
Unusual Fire and Explosion:
In a fire, aerosol cans may explode. Cool cans with water spray and move to safety as soon as possible.
VI. Accidental Release Measures:
Steps to be Taken in Case Material is Released or Spilled:
Ventilate spill area. Remove all sources of ignition. Cover liquid with an absorbent material (sawdust, vermiculite or wet
sand). After the material is absorbed scoop up and place in containers for disposal.
VII. Handling and Storage:
Precautions to be Taken:
Store in a cool, dry place away from sunlight or temperatures above 120掳F. Vapors of this product are heavier than air and
will collect in low places. Use in a well ventilated area.
Other Precautions:
Do not puncture or incinerate aerosol containers.
VIII. Exposure Controls/Personal Protection:
Ventilitation Requirements:
Local Exhaust: Provide mechanical (general) and/or local exhaust ventilation to control airborne levels below the exposure
guidelines.
Personal Protective Equipment:
RESPIRATORY PROTECTION: If airborne concentrations exceed established exposure limits, use a supplied air respirator
or a purifying cartridge respirator suitable for organic vapors.
PROTECTIVE GLOVES: Impervious rubber gloves.
Page 3 of 4 Date Printed: 05/14/2002
MSDS - Material Safety Data Sheet
Product Name: Synlube 1711 Aerosol
MSDS No.: 042902
EYE PROTECTION: Wear safety glasses or goggles.
OTHER PROTECTIVE CLOTHING OR EQUIPMENT: An apron or suitable clothing to prevent skin contact.
IX. Physical and Chemical Properties:
Boiling Point: NA Melting Point: NA Evaporation Rate: <1
Vapor Pressure (mm Hg.): NE Vapor Density (AIR = 1): >1
Solubility In Water: Nil
Apprearance and Odor: Clear liquid; ether-like odor
Other Information: VOLATILITY @75掳F: High
PERCENT VOLATILE BY VOLUME(%): 95%
SPECIFIC GRAVITY: 1.1
X. Stability and Reactivity:
Stability:
Stable
Incompatibility (Materials to Avoid):
Alkalies and strong oxidizing agents. Avoid open flames, hot metal surfaces and other high temperature sources.
Decomposition/By Products:
Hydrocarbon decomposition products at elevated temperatures, halogens, halogen acids and carbonyl halides.
Hazardous Polymerization:
Will not occur.
XI. Toxicological Information:
None Available
XII. Ecological Information:
None Available
XIII. Disposal Considerations:
Waste must be disposed of in accordance with federal, state and local environmental regulations.
XIV. Transport Information:
Box, Aerosols, Non-Flammable
2.2
UN1950
Hazardous
XV. Regulatory Information:
SARA 313 INFORMATION: This product contains the following substances subject to the reporting requirements of Section
313 of Title III of the Superfund Amendments and Reauthorization Act of 1986 and 40 CFR part 372:
CHEMICAL NAME CAS NUMBER CONCENTRATION
1,1-Dichloro-1-Fluoroethane 1717-00-6 59-64%
(HCFC-141b)
Page 4 of 4 Date Printed: 05/14/2002
MSDS - Material Safety Data Sheet
Product Name: Synlube 1711 Aerosol
MSDS No.: 042902
XVI. Other Information:
In this document the following abbreviations were used:
NA: Not Applicable
NE: Not Established
ALL Chemical Property And Toxicity Analysis PAGES IN THIS GROUP