MSDS4409
MATERIAL SAFETY DATA SHEET
May be used to comply with OSHA鈥檚 Hazard Communication
HMIS HAZARD RATING
Standard 29 CFR 1910.1200. Standard must be consulted for
specific requirements.
HEALTH 2 0 = INSIGNIFICANT 3 = HIGH
FLAMMABILITY 3 1 = SLIGHT 4 = EXTREME
REACTIVITY 0 2 = MODERATE
SAFETEC OF AMERICA TRANSPORTATION INFORMATION
PROPER SHIPPING NAME Flammable liquid, n.o.s. (Ethanol)
HAZARD CLASS / PKG. GRP. REF. 173.150(b)(c)
3 / II
IDENTIFICATION NUMBER UN1993 LABEL None Required
SECTION 1 - PRODUCT / COMPANY IDENTIFICATION
IDENTITY (AS USED ON LABEL AND LIST) Page 1 of 2
TM
Safetec Sting Relief
MANUFACTURER鈥橲 NAME EMERGENCY TELEPHONE NUMBER (24 Hours)
Safetec of America, Inc. (800) 255-3924
ADDRESS (NUMBER, STREET, P.O. BOX) TELEPHONE NUMBER FOR INFORMATION
887 Kensington Avenue @ William L. Gaiter Pkwy. (716) 895-1822
(CITY, STATE AND ZIP CODE) DATE PREPARED September 1, 2004
SUPERSEDES June 4, 2001
Buffalo, NY 14215
SECTION 2 - HAZARDOUS INGREDIENTS / IDENTITY INFORMATION
CAS # % (wt.) OSHA PEL/STEL ACGIH TLV/TWA/STEL
HAZARDOUS COMPONENTS
MG/M3 MG/M3
(SPECIFIC CHEMICAL IDENTITY; COMMON NAME(S)) (OPTIONAL) PPM PPM
Ethyl Alcohol 64-17-5 1000 (PEL) 1000 (TLV)
Lidocaine HCl 6108-05-0 2 None Established None Established
Menthol 2216-51-5 None Established None Established
This product is not known to contain a substance subject to Section 313 of Title III of the Superfund Amendments
and Reauthorization Act of 1986 (SARA) and 40 CFR 372 at or above minimal amounts.
SECTION 3 - HEALTH HAZARD DATA
ROUTES OF ENTRY - SIGNS AND SYMPTOMS OF EXPOSURE EMERGENCY AND FIRST AID PROCEDURES
EYES: Brief contact may cause mild irritation; prolonged Flush eyes with clear running water for a minimum of 15
contact may cause moderate irritation associated with minutes while holding eyelids open; if irritation persists, seek
redness. medical attention.
INHALATION: Brief (minutes) inhalation will not cause If irritation occurs, remove to fresh air and provide oxygen if
adverse effects; prolonged and constant inhalation may breathing is difficult; seek medical attention if required
cause irritation to the upper respiratory tract.
SKIN: Prolonged or repeated skin contact may cause mild If irritation occurs, flush with clear running water for a
irritation. minimum of 15 minutes; if irritation persists, seek medical
attention.
INGESTION: Small amounts swallowed incidental to normal DO NOT induce vomiting; seek immediate medical attention.
handling are not likely to cause injury. Swallowing larger
amounts may cause injury.
HEALTH HAZARDS (ACUTE AND CHRONIC): Acute effects are possible irritation and discomfort; chronic effects are
possible with the ingestion of large amounts to the nervous system. Do not use on abraded skin.
NTP? No IARC MONOGRAPHS? No OSHA REGULATED? No
CARCINOGENICITY
No additional information
MEDICAL CONDITIONS GENERALLY AGGRAVATED BY EXPOSURE: Preexisting skin, eye or respiratory disorders may
become aggravated through prolonged exposure.
Form Revised 1/99
MATERIAL SAFETY DATA SHEET
IDENTITY (AS USED ON LABEL AND LIST) Page 2 of 2
Safetec Sting Relief TM Date: September 1, 2004
SECTION 4 - FIRE FIGHTING MEASURES
FLASH POINT (TOC) FLAMMABLE LIMITS (% Volume in Air for Lowest Flashing Component)
15.7掳C LEL: 3.3 UEL: 19
EXTINGUISHING MEDIA
dry chemicals, alcohol-type or all-purpose foam, CO2
SPECIAL FIRE FIGHTING PROCEDURES
DO NOT enter confine fire space without full bunker gear (Helmet with face shield, bunker coats, gloves and rubber boots. Wear
NIOSH/MSHA approved self contained breathing apparatus. Cool fire exposed containers with water. A water spray may be used to
dispense vapors; re-ignition is possible.
UNUSUAL FIRE AND EXPLOSIVE HAZARDS
Flammable liquid. Concentrated vapors may be flammable.
SECTION 5 - PRECAUTIONS FOR SAFE HANDLING AND USE / LEAK PROCEDURES
STEPS TO BE TAKEN IF MATERIAL IS SPILLED OR RELEASED
Small spills may be flushed with large amounts of water; larger spills should be collected with approved absorbent for disposal.
WASTE DISPOSAL METHODS
Dispose of in accordance with Local, State, and Federal regulations. Products classified as non-hazardous may become hazardous
waste upon contact with other products. Refer to "40 CFR Protection of Environment Parts 260-299" for complete waste disposal
regulations. Consult your Local, State, or Federal Environmental Protection Agency before disposing of any chemicals.
PRECAUTIONS TO BE TAKEN IN HANDLING AND STORAGE
Keep container(s) tightly closed when not in use. Store in cool, dry area away from possible sources of ignition. Keep this and other
chemicals out of reach of children.
SECTION 6 - EXPOSURE CONTROLS / PERSONAL PROTECTION
LOCAL EXHAUST: Required
RESPIRATORY PROTECTION VENTILATION
Ordinarily, none required MECHANICAL (GENERAL): No
EYE PROTECTION
PROTECTIVE GLOVES
Ordinarily, none required Ordinarily, none required
WORK / HYGIENIC PRACTICES
OTHER PROTECTIVE CLOTHING OR EQUIPMENT
Ordinarily, none required Practice safe work habits. Use according to label instructions.
SECTION 7 - PHYSICAL / CHEMICAL PROPERTIES
SPECIFIC GRAVITY (WATER=1)
BOILING POINT
0.92
173qF (Based on Ethyl Alcohol)
MELTING POINT
VAPOR PRESSURE (mm Hg)
Not Determined Not applicable
pH
VAPOR DENSITY (AIR=1)
Not Determined Approximately 4.3
EVAPORATION RATE (n-BUTYL ACETATE=1)
SOLUBILITY IN WATER
Complete to moderate Not Determined
% VOLATILES (BY WEIGHT)
APPEARANCE AND ODOR
Clear liquid. Not Determined
SECTION 8 - STABILITY AND REACTIVITY
UNSTABLE: CONDITIONS TO AVOID
STABILITY
STABLE: XXX Extreme temperatures; sources of ignition
INCOMPATIBILITIES (MATERIALS TO AVOID)
Strong oxidizing/reducing agents
HAZARDOUS DECOMPOSITION OR BYPRODUCTS
Decomposition will not occur if handled / stored properly. Thermal decomposition may produce carbon monoxide, small amounts of
nitrogen oxides, halogenated compounds or propionaldehyde may also be formed.
MAY OCCUR:
HAZARDOUS POLYMERIZATION
WILL NOT OCCUR: XXX
The information contained herein is believed to be accurate but is not warranted to be so. Users are advised to confirm in advance of need that information
is current, applicable and suited to the circumstances of use. Vendor assumes no responsibility for injury to vendee or third persons proximately caused by
the material if reasonable safety procedures are not adhered to as stipulated in the data sheet. Furthermore, vendor assumes no responsibility for injury
caused by abnormal use of this material even if reasonable safety procedures are followed.
MSDS PREPARED BY: Safetec of America, Inc., 887 Kensington Avenue @ William L. Gaiter Pkwy., Buffalo, NY 14215 (716) 895-1822
Form Revised 1/99
Dynarex Corporation
MATERIAL SAFETY DATA SHEET
#1103 #1104
NORPAK ALCOHOL SWABS/PREP PADS
Section I -- General Information
Product Name: Alcohol Swabs/Prep Pads
Product Use: Medical Skin Cleansing
WHMIS Classification: Class B, Div. 2 Flammable Liquid
(For 99% alcohol only) Class D, Div. 2 Sub "B" Toxic
Date effective: Jan 5, 1999
Revised by: K.S. Alim
Section II -- Hazardous Ingredients
INGREDIENTS CAS NUMBER WT. % ACGIH-TLV LC/50 LD/50 LD/50
(ppm TWA) (8 hrs. rat) (oral, rat) (Dermal Rabbit)
Isopropyl 67-63-0 33.3 400 12,000 ppm 4,720 mg/kg 12.9 g/kg
Alcohol (99%)
鈥? Each Individual swab contains approximately 0.6 ml of application solution.
The application solution consists of 70% Isopropyl Alcohol and 30% purified D.I. Water.
Section III -- Physical Data
Physical State: Individually sealed alcohol - impregnated swabs
Odor: a) No odor when swab is sealed
b) Alcohol odor when pouch is opened
file:///C|/Documents and Settings/e03383/Local Settings/Temporary Internet Files/OLK8F/Alcohol preps dynarex.html (1 of 4) [10/29/2007 4:16:13 PM]
Dynarex Corporation
Vapor Pressure: 4.4 Kpa@ 20掳C (for 99% alcohol only)
Boiling Point (掳C): Not applicable for swabs
Solubility in-Water: Not applicable for swabs
Specific Gravity: Not applicable for swabs
Volatility/Vol (%): 100 (for 99% alcohol only)
Evaporation Rate (n-BuAC=1): 1.44 (for 99% alcohol only)
Section IV -- Fire and Explosion Data
Flammability: Flammable liquid on combustible tissue
Flash Point (掳C, TCC) 14 (for 99% alcohol only) TCC
Auto ignition Temperature: 399掳C (for 99% alcohol only)
Flammable Limits (Vol. %) LEL 2 (for 99% alcohol only)
LEL 12 (for 99% alcohol only)
Hazardous Combustion Products: Fumes, smoke, oxides of carbon
Extinguishing Media: Dry chemical, carbon dioxide
Alcohol foam, water as extinguishing agents.
Special Fire Hazard: Keep away from sources of extreme heat
Section V -- Reactivity Data
Chemical Stability: Stable
Materials to avoid: Strong oxidizing agents
Section VI -- Health Hazard Data
(For 99% alcohol only) Low to moderate toxicity. Vapors in high concentrations are imitating
Inhalation: and anesthetic.
Eye contact: May cause imitation and lead to tissue damage if exposure persists
Skin contact: Very low order of toxicity by skin absorption. Frequent or prolonged
use may cause skin irritation and dermatitis.
Ingestion: Low order of toxicity.
file:///C|/Documents and Settings/e03383/Local Settings/Temporary Internet Files/OLK8F/Alcohol preps dynarex.html (2 of 4) [10/29/2007 4:16:13 PM]
Dynarex Corporation
Section VII -- Precautions for Safe Use and Handling
General: Store product in cool place. The Individual swabs are for external
application only.
Leak and Spill Due to product packaging (sealed swabs) the chance of a spill is
negligible.
Waste Disposal: Dispose of used swabs as normal household trash.
Section VIII -- Emergency First Aid Procedures
(For 99% alcohol only) If eye contact occurs, immediately flush with water for several
Contact with eyes: minutes, until irritation subsides. If irritation persists, obtain medical
attention.
Contact with skin: Wash with soap and water.
Inhalation: Remove from contaminated area. Apply artificial respiration if
breathing has stopped. Obtain medical attention.
Ingestion: Do not induce vomiting. Keep at rest and call a physician.
Ingestion of swab: Not a normal route of exposure. However, if ingested, remove swab
and rinse mouth several time with water.
Disclaimer:
Information for this material safety data sheet was obtained from sources considered
technically accurate and reliable. While every point has been made to ensure full solitaire of
product hazards, in some cases data is not available and is so stated. Since conditions of
actual product use are beyond control of the supplier, it is assumed that user of this material
has been fully trained according to the mandatory requirements. The buyer assumes all risk of
use, storage and handling to comply with local, provincial/state and federal regulations. No
warranty, expressed or implied, is made and supplier will not be liable for any losses, injuries
or consequential damages, which may result from the use of or reliance on any information
contained in this form. If user requires independent information on this or any other material,
we recommend contacting the Canadian Center for Occupational Health and Safety (OCOHS)
in Hamilton, Oration (1-800-263-8276) or CSTS in Montreal, Quebec (514-873-3990).
file:///C|/Documents and Settings/e03383/Local Settings/Temporary Internet Files/OLK8F/Alcohol preps dynarex.html (3 of 4) [10/29/2007 4:16:13 PM]
Dynarex Corporation
Executive Headquarters: 10 Glenshaw Street, Orangeburg, NY
10962
Dynarex Corporation
Phone: (845) 365-8200 鈥? Toll Free: (888) 335-7500 鈥? (888)
DYNAREX
Fax: (845) 365-8201 鈥? Email: sales@dynarex.com 鈥? www.
dynarex.com
file:///C|/Documents and Settings/e03383/Local Settings/Temporary Internet Files/OLK8F/Alcohol preps dynarex.html (4 of 4) [10/29/2007 4:16:13 PM]
MSDS Material Safety Data Sheet
Blistex Inc.
Blistex Foille Ointment 1 3
Page of
MSDS Number: 025-9302 Revision Date: 11/10/04
1 PRODUCT AND COMPANY IDENTIFICATION
Manufacturer
Blistex Inc.
1800 Swift Drive
Oak Brook, IL 60523
Contact: Director of Quality Systems
Telephone Number: (630) 571-2870
FAX Number:
E-Mail:
Web
Product Name: Blistex Foille Ointment
Revision Date: 11/10/04
MSDS Number: 025-9302
2 COMPOSITION/INFORMATION ON INGREDIENTS
3 HAZARDS IDENTIFICATION
Route of Entry: Skin, Ingestion, Mucus membranes
Target Organs: N/A
Inhalation: No
Skin Contact: Mild allergic conditions in and around the lip area may occur. Irritation and swelling may develop.
Eye Contact: Irritation
Ingestion: N/A
MSDS Material Safety Data Sheet
Blistex Inc.
Blistex Foille Ointment 2 3
Page of
MSDS Number: 025-9302 Revision Date: 11/10/04
4 FIRST AID MEASURES
Inhalation: N/A
Skin Contact: Wash with luke warm water and mild soap.
If irritation or rash develops, stop use. If condition does not improve in several days, seek medical
assistance.
Eye Contact: Flush with luke warm water for 15 minutes.
Ingestion: If discomfort or concerns arise, contact a physician or Poison Control Center.
5 FIRE FIGHTING MEASURES
Flash Point: < 545 F
Flash Point Method: Open Cup
Burning Rate: Unknown
Autoignition Temperature: Unknown
LEL: Unknown
UEL: Unknown
CO2, Dry Chemical, Foam
6 ACCIDENTAL RELEASE MEASURES
Use inert absorbent material to collect spilled product. Collect and place in drums for disposal.
Dispose of according to local, state and federal regulations.
7 HANDLING AND STORAGE
Handling Precautions: Keep in closed containers when in bulk form.
Storage Requirements: Store at room temperature.
8 EXPOSURE CONTROLS/PERSONAL PROTECTION
Engineering Controls: N/A
Protective Equipment: Use NIOSH approved gloves and goggles when handling in raw, bulk form.
9 PHYSICAL AND CHEMICAL PROPERTIES
Appearance: Homogeneous Ointment - Greenish-yellow/green cast
Physical State: Creamy Boiling Point: N/A
Odor: Characteristic Freezing/Melting Pt.: N/A
pH: 6.0 - 8.2 Solubility: Insoluble in water
Vapor Pressure: N/A Spec Grav./Density: 0.910 - 0.930
Vapor Density: N/A
MSDS Material Safety Data Sheet
Blistex Inc.
Blistex Foille Ointment 3 3
Page of
MSDS Number: 025-9302 Revision Date: 11/10/04
10 STABILITY AND REACTIVITY
Stability: Stable
Conditions to avoid: Intense heat - Freezing
Materials to avoid (incompatability): Oxidizing agents
Hazardous Decomposition products: None
Hazardous Polymerization: None
11 TOXICOLOGICAL INFORMATION
12 ECOLOGICAL INFORMATION
13 DISPOSAL CONSIDERATIONS
Follow local, state and federal regulations.
14 TRANSPORT INFORMATION
15 REGULATORY INFORMATION
16 OTHER INFORMATION
END OF MSDS DOCUMENT
MSDS4409
MATERIAL SAFETY DATA SHEET
James Alexander Corporation 845 Route 94 Blairstown, NJ 07825
庐
Product Name: MEDICAINE STING AND BITE RELIEF
Page 1 of 5
MSDS Effective Date: September 10, 2004
CHEMTREC 24 Hour Emergency Phone: (800) 424-9300 Note: The CHEMTREC emergency
number is to be used only in the event of chemical emergencies involving a spill, leak, fire, exposure, or accident
involving chemicals. All non-emergency questions should be directed to JAC at (908) 362-9266.
------------------------------I. PRODUCT IDENTIFICATION -------------------------------
Manufacturer鈥檚 Name: James Alexander Corporation Phone: (908)362-9266
Emergency Telephone No.: (800)424-9300 (CHEMTREC)
Address: 845 Route 94 Blairstown, NJ 07825
庐
Product Name: MEDICAINE STING AND BITE RELIEF
Synonyms: N/A
D.O.T. Shipping Name: Consumer Commodity- ORM-D for ground shipments
Flammable Liquid NOS, 3, UN1993, PGII (contains isopropanol) for
air shipments only
NFPA Ratings: Health - 2 Flammability - 3 Instability - 0
------------------------------II. HAZARDOUS INGREDIENTS ------------------------------
---------OSHA-------- ---------ACGIH---------
Component CAS No. % PEL/TWA TLV/TWA TLV/STEL
Isopropyl Alcohol 67-63-0 29% 400 ppm 400 ppm 500 ppm
2216-51-5 1% N/A N/A
Menthol
---------------------------------------III. PHYSICAL DATA --------------------------------------
Boiling Point: N/A for mixtures Melting Point: Unknown
Specific Gravity: 1.029 25/25 Vapor Pressure: Unknown
Vapor Density: Unknown Solubility in water: Very soluble
% volatiles by vol.: 29% Evaporation Rate (Butyl acetate=1): Unknown
Appearance and odor: Clear, dark green liquid. Odor of isopropyl alcohol, residual odor of
menthol.
pH: Unknown
-----------------------IV FIRE & EXPLOSION INFORMATION ------------------------
Flash Point: 62 degrees F Test Method: Pensky Martens Closed Cup
Autoignition temp: Isopropyl Alcohol: 852 degrees F (456oC)
MATERIAL SAFETY DATA SHEET
James Alexander Corporation 845 Route 94 Blairstown, NJ 07825
庐
Product Name: MEDICAINE STING AND BITE RELIEF
Page 2 of 5
MSDS Effective Date: September 10, 2004
CHEMTREC 24 Hour Emergency Phone: (800) 424-9300 Note: The CHEMTREC emergency
number is to be used only in the event of chemical emergencies involving a spill, leak, fire, exposure, or accident
involving chemicals. All non-emergency questions should be directed to JAC at (908) 362-9266.
Flammable limits in air % by volume: Lower (Unknown) Upper(Unknown)
Extinguishing media: 鈥淎lcohol resistant鈥? foam, CO2 or dry chemical.
Special fire fighting procedures:
NOTE: Individuals should perform only those fire-fighting procedures for which they
have been trained.
Remove all sources of ignition. Move exposed containers from fire area if it can be done
without risk. Firefighters should wear proper protective equipment and self-contained breathing
apparatus with full facepiece operated in positive pressure mode. Spray extinguishing media
directly into base of flames. Water may be used to keep fire-exposed containers cool.
Unusual fire and explosion hazard: When heated, mixture will give off carbon monoxide and
unidentified organic compounds. Closed containers exposed to heat may develop pressure and
explode.
-------------------------V. HEALTH HAZARD INFORMATION -------------------------
Primary routes of exposure: Inhalation, eye contact, skin contact, ingestion.
Signs and symptoms of overexposure:
Inhalation: May cause mild irritation to the nose, throat, and respiratory tract and may
result in depression of the central nervous system.
Eye contact: Moderately irritating to the eyes.
Skin contact: Mildly irritating to the skin.
Ingestion: Irritating to the gastrointestinal tract. May cause abdominal pain and
vomiting (sometimes bloody). Ingestion may cause central nervous system depression, low blood
pressure, rapid heart beat and liver damage.
Early to moderate central nervous system depression may be evidenced by giddiness,
headache, dizziness and nausea. In extreme cases, unconsciousness, respiratory depression and
death may occur. Liver damage may be evidenced by loss of appetite, jaundice (yellowish skin
color) and sometimes pain in the upper abdomen on the right side.
Medical Conditions Aggravated by Exposure: Individuals with pre-existing skin disorders,
eye problems, or impaired respiratory function may be more susceptible to the effects of
overexposure.
MATERIAL SAFETY DATA SHEET
James Alexander Corporation 845 Route 94 Blairstown, NJ 07825
庐
Product Name: MEDICAINE STING AND BITE RELIEF
Page 3 of 5
MSDS Effective Date: September 10, 2004
CHEMTREC 24 Hour Emergency Phone: (800) 424-9300 Note: The CHEMTREC emergency
number is to be used only in the event of chemical emergencies involving a spill, leak, fire, exposure, or accident
involving chemicals. All non-emergency questions should be directed to JAC at (908) 362-9266.
----------------VI. EMERGENCY AND FIRST AID PROCEDURES ----------------
For Inhalation: Remove subject immediately to fresh air. Give artificial respiration if
victim is not breathing. If breathing is difficult, give oxygen. Get immediate medical attention.
For Eye Contact: Immediately flush eyes with copious amounts of water for at least 15
minutes. Eyelids should be held apart and away from eyeball for thorough rinsing. Do not permit
victim to rub eyes. Get immediate medical attention.
For Skin Contact: Immediately flush skin with copious amounts of water for at least 15
minutes while removing contaminated clothing and shoes. Obtain medical attention if irritation
persists after washing. Wash clothing before re-use.
For Ingestion: Contact a Poison Control Center immediately. Give no more than 2
glasses of water and induce vomiting by giving 30 cc (2 tablespoons) of syrup of ipecac. If
victim is a child, give no more than 1 glass of water and 15cc (1 tablespoon) syrup of ipecac. If
syrup of ipecac is unavailable, give 2 glasses of water and induce vomiting by touching finger to
back of victim鈥檚 throat. Do not give anything by mouth to an unconscious or convulsing person.
Get immediate medical attention.
-------------------------------------VII. TOXICITY DATA ---------------------------------------
None of the components present in this formulation are currently classified as
carcinogens in the NTP Annual Report on Carcinogens, IARC Monographs or by OSHA.
------------------------------VIII. PERSONAL PROTECTION ------------------------------
Storage Requirements: Protect containers from physical damage. Detached or outside
storage is preferred. Inside storage should be in an NFPA approved flammable liquids storage
room or cabinet. Store at temperatures below 77 degrees F (25oC). Do not store in direct
sunlight. Isolate from incompatible materials. Keep containers tightly closed.
Handling Requirements: All ignition sources should be eliminated. Remove closure
carefully; internal pressure may be present. Keep closure up to prevent leakage. When contents
are being transferred, metallic containers must be bonded to the receiving container and
grounded to avoid static discharges. Never use pressure to empty containers. Replace closure
carefully after each opening.
Ventilation: Not required for product (JAC unit dose swab) use. When handling bulk
material, use general or local exhaust ventilation to meet TLV requirements. Where engineering
controls are not feasible or sufficient to achieve full conformance with acceptable exposure
limits, use a NIOSH approved respirator designed for organic vapors.
MATERIAL SAFETY DATA SHEET
James Alexander Corporation 845 Route 94 Blairstown, NJ 07825
庐
Product Name: MEDICAINE STING AND BITE RELIEF
Page 4 of 5
MSDS Effective Date: September 10, 2004
CHEMTREC 24 Hour Emergency Phone: (800) 424-9300 Note: The CHEMTREC emergency
number is to be used only in the event of chemical emergencies involving a spill, leak, fire, exposure, or accident
involving chemicals. All non-emergency questions should be directed to JAC at (908) 362-9266.
Eye Protection: Not required for product (JAC unit dose swab) use. When handling bulk
material, always wear gas-tight, splash-proof chemical safety goggles meeting OSHA 29CFR
1910.133 specifications.
Skin Protection: Not required for product (JAC unit dose swab) use. When handling
bulk material, use nitrile, neoprene or natural rubber gloves for most effective skin protection.
-------------------------------IX. HAZARDOUS REACTIVITY -------------------------------
Stable at room temperature. Hazardous polymerization will not occur. However, carbon
monoxide gas and unidentified organic compounds may be formed during combustion.
Conditions To Avoid: Sunlight, heat (heating above ambient temperatures causes the
vapor pressure of the material to increase). Avoid contact with strong oxidizing agents.
Do not store or handle in aluminum equipment at temperatures above 120 degrees F.
-----------------X SPILL, LEAK AND DISPOSAL PROCEDURES ------------------
For large spills, stop leak if you can do so without risk. Extinguish all sources of ignition.
Wear self-contained breathing apparatus, chemical safety goggles and full protective clothing.
Ventilate area. Spilled liquids should be contained and not washed into sewers or ground water.
Contain by diking with non-combustible absorbent materials and place residue in DOT approved
waste container.
Comply with all applicable local, state and federal regulations on spill reporting, handling
and disposal of waste.
Other Precautions: Containers, even those that have been emptied, will retain product
residue and vapors. Handle empty containers as if they were full.
Prepared By: David Robinson
Title: Vice President
Date of Initial Preparation: June 1989
Latest Revision Date: September 10, 2004
------------------------------------------------------------------------------------------------------------------
NOTE: This Material Safety Data Sheet is intended only as a guide to the appropriate
precautionary handling of the material by a person trained in, or supervised by a person trained
in, the safe handling of chemical materials.
James Alexander Corporation (JAC), expressly disclaims all express or implied
warranties of merchantability and fitness for a particular purpose with respect to the product or
information provided herein.
MATERIAL SAFETY DATA SHEET
James Alexander Corporation 845 Route 94 Blairstown, NJ 07825
庐
Product Name: MEDICAINE STING AND BITE RELIEF
Page 5 of 5
MSDS Effective Date: September 10, 2004
CHEMTREC 24 Hour Emergency Phone: (800) 424-9300 Note: The CHEMTREC emergency
number is to be used only in the event of chemical emergencies involving a spill, leak, fire, exposure, or accident
involving chemicals. All non-emergency questions should be directed to JAC at (908) 362-9266.
All information appearing herein is based upon data obtained from the manufacturer(s)
and/or recognized technical sources. While the information is believed to be accurate, JAC
makes no representations as to its accuracy or sufficiency. Conditions of use are beyond JAC鈥檚
control and therefore, users are responsible to verify this data under their own operating
conditions to determine whether the product is suitable for their particular purposes and they
assume all risks of their use, handling, and disposal of the product, or from the publication or use
of, or reliance upon, information contained herein. This information relates only to the product
designated herein and does not relate to its use in combination with any other material or in any
other process.
PDI - PROFESSIONAL DISPOSABLES, INC.
THE HEALTHCARE DIVISION OF
NP
NICE-PAK PRODUCTS, INC. ISO 9001
TWO NICE-PAK PARK CERTIFIED
ORANGEBURG NY 10962-1376
845-365-1700
REVISION DATE: 7/00
I. PRODUCT IDENTIFICATION
PRODUCT/TRADE NAME: AMMONIA INHALANT B37500
HAZARD RATING (NFPA)
HEALTH: 2
FLAMMABILITY: 2
REACTIVITY: 0
SPECIFIC: NONE
EMERGENCY OR INFORMATION TELEPHONE NO: 845-365-1700 (M-F DAYTIME) AT OTHER TIMES, CONTACT
THE LOCAL POISON CONTROL CENTER
CHEMICAL NAME: MIXTURE
II HAZARDOUS INGREDIENTS PER 29 CFR 1910.1200
Hazardous Ingredients % ACGIH TLV CAS NUMBER
ISOPROPYL ALCOHOL 20 400 ppm 67-63-0
AMMONIA 15 50 ppm 1336-21-6
III-PHYSICAL/CHEMICAL CHARACTERISTICS
COLOR/ODOR/APPEARANCE: TOWELETTE/PAD SATURATED WITH CLEAR LIQUID WITH STRONG AMMONIA
ODOR
BOILING POINT: N/A
FLASH POINT: N/A
VAPOR DENSITY N/A
EVAPORATION RATE: N/A
SOLUBILITY IN WATER: COMPLETE
SPECIFIC GRAVITY (H2O = 1): N/A
IV FIRE & EXPLOSION HAZARD DATA
FLASH POINT(Method Used): N/A : LEL: N/A UEL: N/A
EXTINGUISHING MEDIA: DRY CHEMICAL OR ALCOHOL TYPE FOAM
SPECIAL FIRE FIGHTING PROCEDURES: HANDLE AS FLAMMABLE LIQUID
UNUSUAL FIRE AND EXPLOSION HAZARDS: NIOSH APPROVED RESPIRATORY EQUIPMENT FOR FIRE FIGHTING
PERSONNEL
V-REACTIVITY DATA
STABILITY: STABLE
CONDITIONS TO AVOID : NONE KNOWN
INCOMPATIBILITY: IODINE PRODUCTS AND LIQUID BLEACH (CHLORINE)
HAZARDOUS DECOMPOSITION OR BYPRODUCTS: NONE KNOWN
POLYMERIZATION: WILL NOT OCCUR
CONDITIONS TO AVOID: NONE KNOWN
AMMONIA INHALANT
VI-HEALTH HAZARD DATA
EFFECTS OF OVER EXPOSURE:
SKIN : MAY CAUSE IRRITATION AND BURN SKIN
EYES : HIGHLY IRRITATING
INHALATION: CAN CAUSE IRRITATION TO MUCOUS MEMBRANES
INGESTION: DO NOT INGEST
EMERGENCY AND FIRST AID PROCEDURES:
SKIN CONTACT: FLUSH WITH COLD WATER
EYE CONTACT: FLUSH WITH COOL WATER FOR 15 MINUTES
INHALATION: REMOVE TO FRESH AIR
INGESTION: CALL POISON CONTROL CENTER. CALL PHYSICIAN
TARGET ORGANS; NONE KNOWN
KNOWN CARCINOGEN: NONE KNOWN
VII-SPILL AND DISPOSAL PROCEDURE
SPILL CONTROL: VENTILATE AREA. DISPOSE AS HAZARDOUS WASTE
WASTE DISPOSAL DISPOSE AS HAZARDOUS WASTE PER LOCAL, STATE AND FEDERAL REGULATIONS
HANDLING AND STORAGE: DO NOT STORE NEAR HEAT
VIII-CONTROL MEASURES/PROTECTION
RESPIRATION: USE FOR SPILLAGE AND FUMES
VENTILATION: RECOMMENDED
PROTECTIVE GLOVES: YES
EYE PROTECTION: YES
HYGIENIC PRACTICES: HANDLE WITH CARE
OTHER: NONE
IX TRANSPORT/SHIPPING
DOT SHIPPING NAME:
TECHNICAL SHIPPING NAME:
DOT SHIPPING CLASSIFICATION: DOT NOT REGULATED
DOT ID NO.:
DOT ;LABEL; REQUIREMENTS:
UN/NA NUMBER REGULATIONS:
REPORTABLE QUANTITY:
X DISCLAIMER
THE INFORMATION FURNISHED HEREIN IS BELIEVED TO BE ACCURATE AND REPRESENTS THE BEST DATA
CURRENTLY AVAILABLE TO US. NO WARRANTY, EXPRESSED OR IMPLIED IS MADE AND NICE-PAK PRODUCTS,
INC. ASSUMES NO LEGAL RESPONSIBILITY OR LIABILITY RESULTING FROM ITS USE.
|