Universal Tractor Fluid
SECTION 1: PRODUCT AND COMPANY IDENTIFICATION
PRODUCT NAME: SUPROTEK ADVANTAGE UNIVERSAL TRACTOR FLUID
SYNONYMS: Petroleum oil; Lube oil; Petroleum hydrocarbon; Lubricant.
PRODUCT CODE: Prefix 25
PRODUCT USE: A universal tractor fluid for power shift transmissions, final drives, and hydraulics. If this
product is used in combination with other products, refer to the Material Data Safety Sheets for
those products.
This number is for emergency use only. If 24-HOUR EMERGENCY PHONE NUMBER
you desire non-Emergency product MEDICAL AND TRANSPORTATION (SPILL):
information, please call a phone number
listed below. CHEMTREC: (800) 424-9300
SUPPLIER: Dixie Gas & Oil Corporation
229 Lee Highway
Verona, VA 24482
www.dixiegas.com
800-403-4943
TECHNICAL
INFORMATION: 540-248-6273
MSDS FORM NUMBER: 82555 ISSUE: November 4, 2005
ORIGINAL ISSUE: April 22, 1993 SUPERSEDES: December 5, 2002
PREPARED BY: Product MSDS Coordinator APPROVED BY: MSDS Task Force
Page 1 of 8
SECTION 2: COMPOSITION/INFORMATION ON INGREDIENTS
OSHA PEL ACGIH TLV庐
WT NAME SYNONYM CAS NO. TWA STEL TWA STEL LD LCb
% mg/m3 mg/m3 mg/m3 mg/kg mg/L/4
H
90- Lubricating oils, Hydrotreated 64742-58-1 5c N. Av 5 c,d 10c >2000a N. Av
95 petroleum, paraffinic base oil
hydrotreated spent
0- Petroleum distillates, N. Av. 64742-54-7 5c N. Av 5 c,d 10c >2000e >2.18
3* hydrotreated heavy
paraffinic
0- Phosphorodithioic acid, N. Av 68649-42-3 N. Av. N. Av. N. Av. N. Av. N. Av. N. Av.
2* O,Odi-
C1-14-alkyl esters,
zinc
salts
0-2 Calcium sulfonate N. Av. ** Trade N. Av. N. Av. N. Av. N. Av. N. Av. N. Av.
Secret**
N. Av. = Not Available aOral-Rat LD50 (mg/kg)
*Even though the concentration range does not fall under the bInhalation-Rat LC50
ranges prescribed by WHMIS, this is the actual range which crelated to Oil mist, mineral
varies with each batch of the product. dNotice of Intended Changes: Value to be reduced.
**Supplier advises that this is a trade secret
SECTION 3: HAZARDS IDENTIFICATION
EMERGENCY OVERVIEW
APPEARANCE
Amber, liquid, petroleum odor.
CAUTION!
HEALTH HAZARDS
May be harmful if swallowed.
May irritate eyes and skin.
POTENTIAL HEALTH
EFFECTSINGESTION
(SWALLOWING): May cause throat irritation, nausea, vomiting, and diarrhea. Aspiration hazard: Breathing
product into the lungs during ingestion or vomiting may cause lung injury and possible
death.
MEDICAL CONDITIONS
AGGRAVATED BY
EXPOSURE: Individuals with pre-existing respiratory tract (nose, throat, and lungs), eye, and/or skin
disorders may have increased susceptibility to the effects of exposure.
CHRONIC: Prolonged or repeated inhalation of oil mist may cause oil pneumonia, lung tissue
inflammation, and/or fibrous tissue formation. Prolonged or repeated eye contact may
cause inflammation of the membrane lining the eyelids and covering the eyeball
(conjunctivitis). Prolonged or repeated skin contact may
Page 2 of 8
cause drying, cracking, redness, itching, and/or swelling (dermatitis).
CANCER
INFORMATION: For more information, see SECTION 11: CARCINOGENICITY. Also see SECTION 15:
CALIFORNIA.
POTENTIAL
ENVIRONMENTAL
EFFECTS: Not available. Also see SECTION 12: ECOLOGICAL INFORMATION.
SECTION 4: FIRST AID MEASURES
INHALATION
(BREATHING): This product is not likely to present an inhalation hazard at normal temperatures and
pressures. However, when aerosolizing, misting, or heating this product, high
concentrations of generated vapor or mist may irritate the respiratory tract (nose, throat,
and lungs).
EYES: May cause irritation.
SKIN: May cause irritation. Not likely to be absorbed through the skin in harmful amounts.
SKIN: Remove affected clothing and shoes. Wash skin thoroughly with soap and water. Get
medical attention if irritation or pain develops or persists. If product is injected under
pressure into or under the skin, or into any part of the body, regardless of the appearance
of the wound or its size, a physician should immediately evaluate the individual as a
medical emergency. Wash contaminated clothing before reuse.
INGESTION
(SWALLOWING): Do NOT induce vomiting. Immediately get medical attention. Call 1-800-537-7433 for
additional information. If spontaneous vomiting occurs, keep head below hips to avoid
breathing the product into the lungs. Never give anything to an unconscious person by
mouth.
NOTE TO
PHYSICIANS: Treat symptomatically and supportively. Treatment may vary with condition of victim and
specifics of incident. Call 800-424-9300 for additional information.
SECTION 5: FIRE FIGHTING MEASURES
FLASH POINT: 392掳F (200掳C) (minimum) Cleveland open cup
FLAMMABLE
LIMITS IN AIR: LOWER: Not available UPPER: Not available
AUTOIGNITION
TEMPERATURE: Not available
HAZARDOUS
COMBUSTION
PRODUCTS: Decomposition and combustion materials may be toxic. Burning may produce aldehydes,
hydrogen sulfide, alkyl mercaptans, sulfides, calcium oxides, phosphorus oxides, sulfur
oxides, zinc oxides, carbon monoxide, and unidentified organic compounds.
CONDITIONS OF
FLAMMABILITY: Sparks or flame. Product may burn, but does not ignite readily.
Page 3 of 8
EXTINGUISHING MEDIA: Carbon dioxide, regular foam, dry chemical, water spray, or water fog. Water or foam
may cause frothing.
NFPA 704
HAZARD IDENTIFICATION: This information is intended solely for the use by individuals trained in this system.
Health Hazard (Blue) 1 Fire Hazard (Red) 1
Specific Hazard (White) Reactivity (Yellow 0
FIRE FIGHTING
INSTRUCTIONS: Keep storage containers cool with water spray. A positivepressure, self-contained
breathing apparatus (SCBA) and fullbody protective equipment are required for fire
emergencies.
FIRE AND EXPLOSION
HAZARDS: Heated containers may rupture. "Empty" containers may retain residue and can be
dangerous. Product is not sensitive to mechanical impact or static discharge.
SECTION 6: ACCIDENTAL RELEASE MEASURES
Remove all ignition sources. Do not touch or walk through spilled product. Stop leak if you can do it without risk. Wear
protective equipment and provide engineering controls as specified in SECTION 8:
EXPOSURE CONTROLS/PERSONAL PROTECTION. Isolate hazard area. Keep
unnecessary and unprotected personnel from entering. Ventilate area and avoid
breathing vapor or mist. Contain spill away from surface water and sewers. Contain spill
as a liquid for possible recovery, or sorb with compatible sorbent material and shovel with
a clean, sparkproof tool into a sealable container for disposal. Additionally, for large spills:
Dike far ahead of liquid spill for collection and later disposal.
SECTION 7: HANDLING AND STORAGE
HANDLING: Keep away from sparks or flame. Where flammable mixtures may be present, equipment
safe for such locations should be used. Use clean tools and explosion-proof equipment.
When transferring large volumes of product, metal containers, including trucks and tank
cars, should be grounded and bonded. This product has a low vapor pressure and is not
expected to present an inhalation hazard under normal temperatures and pressures.
However, when aerosolizing, misting, or heating this product, do not breathe vapor or
mist. Use in a well ventilated area. Avoid contact with eyes, skin, clothing, and shoes.
SHIPPING AND
STORING: Keep container tightly closed when not in use and during transport. Store containers in a
cool, dry place. Do not pressurize, cut, weld, braze, solder, drill, or grind containers. Keep
containers away from flame, sparks, static electricity, or other sources of ignition. Empty
product containers may retain product residue and can be dangerous.
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION
ENGINEERING
CONTROLS: Provide general ventilation needed to maintain concentration of vapor or mist below
applicable exposure limits. Where adequate general ventilation is unavailable, use
process enclosures, local exhaust ventilation, or other engineering controls to control
airborne levels below applicable exposure limits.
Page 4 of 8
PERSONAL PROTECTIVE EQUIPMENT
RESPIRATORY
PROTECTION: No respiratory protection is normally required. Use NIOSH-certified P- or R- series
particulate filter and organic vapor cartridges when concentration of vapor or mist
exceeds applicable exposure limits. Protection provided by air purifying respirators is
limited. Do not use N-rated respirators. Selection and use of respiratory protective
equipment should be in accordance in the USA with OSHA General Industry Standard 29
CFR 1910.134; or in Canada with CSA Standard Z94.4.
EYE
PROTECTION: Wearing chemical goggles is recommended. Contact lenses may be worn with eye
protection.
SKIN
PROTECTION: No skin protection is normally required. Where prolonged or repeated skin contact is
likely, wear neoprene, nitrile (4 mil minimum), PVC (polyvinyl chloride), or equivalent
protective gloves; use of natural rubber or equivalent gloves is not recommended. When
product is heated and skin contact is likely, wear heat-resistant gloves, boots, and other
protective clothing. To avoid prolonged or repeated contact where spills and splashes are
likely, wear appropriate chemical-resistant faceshield, boots, apron, coveralls, long sleeve
shirts, or other protective clothing.
PERSONAL
HYGIENE: Wash thoroughly with soap and water after handling product and before eating, drinking,
or using tobacco products. Clean affected clothing, shoes, and protective equipment
before reuse. Discard leather articles, such as shoes, saturated with this product.
OTHER
PROTECTIVE
EQUIPMENT: Where spills and splashes are likely, facilities storing or using this product should be
equipped with an emergency eyewash and shower, both equipped with clean water, in
the immediate work area.
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
PHYSICAL STATE,
APPEARANCE, AND ODOR: Amber, liquid, petroleum odor.
ODOR THRESHOLD: Not available
MOLECULAR WEIGHT: Not applicable
SPECIFIC GRAVITY: 0.88 (water = 1)
DENSITY: 7.3 lb/US gal (880 g/L)
VAPOR DENSITY: Not available
VAPOR PRESSURE: less than 0.1 mm Hg @ 68掳F (20掳C)
BOILING POINT: 475掳F (246掳C)
FREEZING/MELTING POINT: Not available
pH: Not applicable
EVAPORATION RATE: Not available
Page 5 of 8
SOLUBILITY IN WATER: Insoluble
FLASH POINT: 392掳F (200掳C) (minimum) Cleveland open cup
FLAMMABLE LIMITS IN AIR: LOWER: Not available UPPER: Not available
AUTOIGNITION TEMPERATURE: Not available
SECTION 10: STABILITY AND REACTIVITY
STABILITY: Stable under normal temperatures and pressures. Avoid sparks or flame.
INCOMPATIBILITY: Avoid acids and oxidizing agents.
REACTIVITY: Polymerization is not known to occur under normal temperature and pressures. Not
reactive with water.
HAZARDOUS
DECOMPOSITION
PRODUCTS: None under normal temperatures and pressures. See also SECTION 5: HAZARDOUS
COMBUSTION
PRODUCTS.
SECTION 11: TOXICOLOGICAL INFORMATION
SENSITIZATION: Based on best current information, there is no known human sensitization associated with
this product.
MUTAGENICITY: Experimental evidence suggests that this product does not cause mutagenesis.
CARCINOGENICITY: No animal skin carcinogenicity tests of the hydrotreated paraffinic base oil CAS 64742-
58-1 have been conducted. Neither OSHA, ACGIH, IARC, nor NTP have classified this
material as to its carcinogenic risk. Based on best current information, for the other
components listed in SECTION 2, there is no known carcinogenicity as regulated by
OSHA; as categorized by ACGIH A1 or A2 substances; as categorized by IARC Group 1,
Group 2A, or Group 2B agents; or as listed by NTP as either known carcinogens or
substances for which there is limited evidence of carcinogenicity in humans or sufficient
evidence of carcinogenicity in experimental animals. Also see SECTION 15:
CALIFORNIA.
REPRODUCTIVE
TOXICITY: Based on best current information, there is no known teratogenicity associated with this
product. Also see SECTION 15: CALIFORNIA.
TERATOGENICITY: Based on best current information, there is no known teratogenicity associated with this
product.
TOXICOLOGICALLY
SYNERGISTIC
PRODUCT(S): Based on best current information, there are no known toxicologically synergistic products
associated with this product.
Page 6 of 8
SECTION 12: ECOLOGICAL INFORMATION
ECOTOXICITY: No information available.
OCTANOL/WATER
PARTITION
COEFFICIENT: Not available
VOLATILE ORGANIC
COMPOUNDS: 100 WT%; 7.3 LB/US gal; 880 g/l (approximately) As per 40 CFR Part 51.100(s).
SECTION 13: DISPOSAL CONSIDERATIONS
DISPOSAL: Dispose in accordance with federal, state, provincial, and local regulations. Regulations
may also apply to empty containers. The responsibility for proper waste disposal lies with
the owner of the waste. Contact Dixie Gas And Oil Corporation. regarding proper
recycling or disposal.
USEPA WASTE
CODE(S): This product, if discarded, is not expected to be a characteristic or listed hazardous
waste. If recycled in the USA, it must be managed in accordance with 40 CFR Part 279.
Processing, use, or contamination by the user may change the waste code(s) applicable
to the disposal of this product.
SECTION 14: TRANSPORT INFORMATION
DOT: Not regulated
TDG: Not regulated.
EMERGENCY RESPONSE
GUIDE NUMBER: Not applicable. Reference North American Emergency Response Guidebook.
SECTION 15: REGULATORY INFORMATION
USA REGULATIONS
SARA SECTIONS
302 AND 304: Based on the ingredient(s) listed in SECTION 2, these products do not contain any
"extremely hazardous substances" listed pursuant to Title III of the Superfund
Amendments and Reauthorization Act of 1986 (SARA)
Section 302 or Section 304 as identified in 40 CFR Part 355, Appendix A and B.
SARA SECTIONS
311 AND 312: This product poses the following health hazard(s) as defined in 40 CFR Part 370 and is
subject to the requirements of sections 311 and 312 of Title III of the Superfund
Amendments and Reauthorization Act of 1986
(SARA):
Immediate (Acute) Health Hazard
Delayed (Chronic) Health Hazard
SARA SECTION
313: This product does contain a "toxic" chemical subject to the requirements of section 313 of
Title III of the Superfund Amendments and Reauthorization Act of 1986 (SARA) and 40
CFR Part 372. Material: Zinc alkyl dithiophosphate (based on the zinc compounds
category); CAS# Not Available
CERCLA: Based on the ingredient(s) listed in SECTION 2, this product does not contain any
"hazardous substances" listed pursuant to the Comprehensive Environmental Response,
Compensation and Liability Act of 1980 (CERCLA) in 40 CFR Part 302, Table 302.4.
Page 7 of 8
TSCA: All the components of this product are listed on, or are exempted from the requirement to
be listed on, the TSCA Inventory.
CALIFORNIA: This product may contain detectable amounts of arsenic CAS 7440-38-2, benzene CAS
71-43-2, and cadmium CAS 7440-43-9, from additives. This product may contain a
detectable amount of benzo(a)anthracene CAS 56-55-3, benzo(b)fluoranthene CAS 205-
99-2, benzo(k)fluoranthene CAS 207-08-9, benzo(a)pyrene CAS 50-32-8, chrysene CAS
218-01-9, dibenz(a,h)anthracene CAS 53-70-3 and indeno(1,2,3-cd)pyrene CAS 193-39-
5. WARNING: These chemicals are known to the State of California to cause cancer. Our
testing of this product indicates that these chemicals are not always detectable. This
product may contain detectable amounts of arsenic CAS 7440-38-2, benzene CAS 71-43-
2, and cadmium CAS 7440-43-9, from additives. WARNING: These chemicals are
known to the State of California to cause birth defects or other reproductive harm.
CANADIAN REGULATIONS
This product has been classified in accordance with the hazard criteria of the Controlled Products Regulations (CPR) and
the MSDS contains all information required by the CPR.
WHMIS: Not regulated.
CANADIAN
ENVIRONMENTAL
PROTECTION
ACT (CEPA): The components of this product are listed on, or are automatically included as "substance
occurring in nature" on, or are exempted from the requirements to be listed on, the
Canadian Domestic Substances List (DSL).
SECTION 16. OTHER INFORMATION
REVISION
INFORMATION: Revised format. This MSDS has been revised in the following sections:1 (Phone
Numbers), 3 (Hazards Identification), 4 (Phone Numbers and Skin First Aid), 9
(Appearance),and 15 (California).
LABEL/OTHER
INFORMATION: Not available.
User assumes all risks incident to the use of this (these) product(s). To the best of our knowledge, the information
contained herein is accurate. However, Dixie Gas And Oil Corporation assumes no liability whatsoever for the accuracy or
completeness of the information contained herein. No representations or warranties, either express or implied, or
merchantability, fitness for a particular purpose or of any other nature are made hereunder with respect to information or
the product to which information refers. The data contained on this sheet apply to the product(s) as supplied to the user.
.
Page 8 of 8
|