PRODUCT DATA









No-Warp Foam

Window & Door Insulating Sealant

                            This is a one-component polyurethane

                            foam specially formulated to seal

                            around window and door frames. The

                            low pressure, airtight insulation foam

                            blocks drafts, moisture and insects

                            without bowing.

                            �   Will not warp frames or jambs



                            �   Exerts up to 90% less curing

                                pressure than other foams



                            � For professional gun applications



                            �   Provides water-resistant,

                                airtight seal



                            �   Bright white



                            �   Handles up to 12 average windows

                                (36 inch x 60 inch; 3/8 inch gap, 1 inch deep)









               Conforms

               to: 812-04

Proud Member

                                                                                                  DIRECTIONS

                                                                                                  Read all directions and cautions before use. For



                           No Warp                                                                additional information, see package label or MSDS.



                                                                                                  �     SURFACE PREP: Surface should be free of

                           Polyurethane Foam Sealant

                                                                                                        dirt, oil, grease and excess moisture.

TECHNICAL DATA

                                                                                                  �     SET-UP: Attach applicator gun to can (do not

�     Density: 1.3-1.8 lbs./cu.ft.

                                                                                                        overtighten), then shake well for 30 seconds.

�     Thermal Resistance: (ASTM C-518)

      R-Valve 4.5 per inch thickness                                                              �     APPLICATION: Dispense foam with can upside

�     Maximum Service Temperature of                                                                    down, testing bead size on scrap material first.

                                                                                                        Fill area about 25% full, leaving room for foam to

      Cured Foam: 240°F (116°C)

                                                                                                        expand. Note: To improve curing in arid regions,

�     Shelf Life: 18 months

                                                                                                        spray a light water mist into the cavity before

�     No CFC’s, No HCFC’s

                                                                                                        applying foam.

�     Contains no urea formaldehyde

�     Safe for wood, aluminum, vinyl and

                                                                                                  �     STORE UPRIGHT (50°-100°F)

      window/door installs

                                                                                                  �     FOAM BONDS TO SKIN QUICKLY. Wear gloves,

                                                                                                        eye protection and work clothes; use drop cloths.

           YIELD ESTIMATE TABLE

                                                                                                  �     FOR BEST RESULTS use in temperatures

    Size(Volume)   Bead Diameter            Linear Feet

    20 oz. can                                  2096                                                    60° - 100° F (50% relative humidity).

                         1/4�

                                                 932

                         3/8�



                                                                                                  �     FINISH: Foam will be tack-free in about 10

ASTM C-1536

                                                                                                        minutes (50% RH). Excess can be trimmed in

                                                                                                        about 30 minutes. Cover or paint foam surfaces

                                                                                                        exposed to direct sunlight.

                                                                                                  �     CAN CHANGEOVER: Once started, do not

                                                                                                        remove gun until can is empty; then purge gun

                                                                                                        and remove can. Clean gun basket with acetone

                                                                                                        or polyurethane foam cleaner. Immediately attach

                                                                                                        fresh can to prevent foam from hardening in gun.





                                                                                                                          UNDERWRITERS LABORATORIES INC.

    also available                                                                                                   CLASSIFIED CAULKING AND SEALANTS                                 R14175

                                                                                                                                      Surface Burning Characteristics

                     Poly-Clean                                                                                                                                                        ILI5

                                                                                                                              Applied To Inorganic Reinforced Cement Board*

                                                                                                                        Flame Spread 10             Smoke Developed 15

                     Polyurethane Foam Cleaner

                                                                                                   *Tested as applied in four 1/2 in. diameter beads, 5 inches on center, covering 8.3% of the

                     � Removes wet foam from hands, tools and                                      exposed test sample area. The test results do not reflect the hazards of this material under

                       foam applicator guns                                                        actual fire conditions.



                     � Trilingual label (English, Spanish, French)

                                                                                                 CAUTION: Contains MDI Monomer, Polyurethane Resin & Propane / Isobutane. Cured foam

                                                                                                 exposed to temperatures in excess of 240°F (116°C) may release hazardous decomposition

                                                                                                 products. Keep away from heat, sparks, flames and static electricity. Turn off sources of ignition

                                                                                                 (pilot light, etc.). Ventilate work area with moving, fresh air. Vapors heavier than air may cause

                                                                                                 flash fire or ignite explosively. Do not puncture, expose to heat or store at temperatures above

                                                                                                 120°F (49°C). Do not leave in auto. Wear protective gloves, safety glasses, work clothes.



                                                                                                 FIRST AID TREATMENT - SKIN CONTACT: DO NOT RINSE WITH WATER (water helps curing).

                                                                                                 If foam is wet: remove immediately with acetone or polyurethane foam cleaner. After removal,

                                                                                                 wash with soap and water. If foam has dried: it is very difficult to remove. Do not try to remove

                                                                                                 with solvents. Cured foam wears off and is not harmful to health. EYE CONTACT: Flush with

                                                                                                 water for 15 minutes and get immediate medical attention. INHALATION: Overexposure to

                     Remove adapter and                                Attach can to gun

                                              Spray cleaner directly

                                                                                                 vapors may cause dizziness or headache � move to fresh air. Consult physician if needed.

                     attach to top of can                              basket to remove

                                              on top of gun for

                                                                                                 INGESTION: Get immediate medical attention. KEEP OUT OF REACH OF CHILDREN.

                     for easy use.                                     foam from gun barrel.

                                              foam removal.





                                                                                                                                                                                  Pallet Qty.

                                                                 Case Pack

                                            Item #

           Product                                                                                                       Master Carton

                                                                                           Unit UPC Code                                                    Case Weight

    No-Warp Foam                      4004529712                  12 / 20 oz.                                                                                                            72

                                                                                                                       1 00 75650 29712 4                        20.24

                                                                                           0 75650 29712 4

    Poly-Clean (US/Canada)            4004712022                  12 / 12 oz.                                                                                                           108

                                                                                                                       1 00 75650 00015 8                          13

                                                                                           0 75650 00015 1









                                                                                                                                                                                 MK-005 (03-06)