PRODUCT DATA
1240
Flex Lox Exterior Coating
PREMIUM 鈥? 100% ACRYLIC 鈥? EXTERIOR 鈥? FLAT 鈥? 1240 LINE
Product Description Vehicle Type
Waterborne 鈥? 100% Acrylic
Flex Lox Exterior Coating is a superior quality, flexible coating formulated
with an exceptional blend of premium durable 100% acrylic resins for use
Finish
as a primer or finish coat. The addition of zinc oxide combined with Flat 鈥? 85掳 Sheen - 1.0 to 10.0
organic mildewcides give Flex Lox Exterior Coating excellent protection
against mildew. The formulation of Flex Lox Exterior Coating gives it a Use
Exterior
high resistance to alkali and efflorescence which makes it an excellent
primer for new stucco and low density masonry block. Flex Lox is
Percent Solids By Weight
designed for use in residential, architectural, commercial and light industrial 58.0% 卤 2%
applications on various substrates.
Percent Solids By Volume
Performance 44.0% 卤 2%
鈥? Excellent primer for new stucco and low density masonry block Suggested Coverage
鈥? Exceptional resistance to alkali and efflorescence 200 SFPG
鈥? Excellent for use as a finish coat (depending on porosity and DFT)
鈥? Allows moisture vapor transmission Dry Film Thickness
鈥? Easy to apply, high build formulation for excellent coverage 3.6 mils @ 200 SFPG
鈥? Excellent color retention and chalk resistance (custom DFT's can be specified)
Nonporous surfaces like metal and wood
鈥? Extremely durable and flexible with excellent adhesion do not require a high DFT.
鈥? Bridges hairline cracks
鈥? Excellent resistance to mildew and organic growth Viscosity
108 KU 卤 5
鈥? Excellent resistance to blistering, cracking, chipping and peeling
Flash Point
May be applied to properly primed and prepared鈥?
Nonflammable 鈥? >200掳 F.
鈥? Concrete, Masonry and Stucco including:
VOC
Brick , Cement Plaster, Poured and Precast Concrete, Contains .79 lbs./gal. (95 gms./ltr.)
Concrete Masonry Units (CMU), Cementitious Siding Complies with all Federal, State
and Local VOC standards.
鈥? Synthetic Masonry Stucco (EIFS)
鈥? Wood, Plywood, Hardboard and Gypsum Wallboard Application Equipment
鈥? Aluminum, Galvanized Metals and Ferrous Metal Brush, roller, airless or
conventional spray
Specification Standards
Drying Time
Performance alternate for Federal Specification TT-P-19D; TT-P-96D At 75掳F. / 50% RH
Exceeds Federal Specification for resistance to wind driven rain: TT-C-555B 1 hour to touch
section 3.3.3 - 98 m.p.h. Wind Driven Test. 4 hours to recoat
Passes ASTM D2370 - 350% Elongation at Break / 200 psi Tensile Strength.
Colors
Limitations White, off whites, pastel. light,
medium, deep colors and accent
Allow a minimum of three (3) days of cure time for new masonry, a seven colors
(7) day cure time for poured in place concrete and a pH level of 13 or lower
Products Included in This Line
prior to application of product. Coatings have a greater resistance against
1240 - White
failure when applied to a surface with a lower alkaline level (below 8.5).
1241 - Tint White
Not recommended for steps, walkways, or other foot or vehicle traffic 1242 - Deep Base
areas. Do not use for immersion service, below grade substrates, or 1244 - Accent Base
substrates constantly in contact with moisture. Do not use in highly
corrosive or chemical environments, or areas subject to intense heat.
COLOR WHEEL PAINT MANUFACTURING COMPANY, INC.
Product Index 鈥? Category 1
2814 Silver Star Road 鈥? Orlando, Florida 32808
407-293-6810 鈥? 800-749-6810 鈥? Fax 407-293-0945
Exterior Paints & Coatings
www.colorwheel.com
09900
1240.04.7 / PDS / 1
1240 LINE FLEX LOX EXTERIOR COATING 鈥? PREMIUM 鈥? 100% ACRYLIC 鈥? EXTERIOR 鈥? FLAT
Surface Preparation Recommended Primers (continued) Curing
The performance of this product is critically New Wood and Hardboard: Can be self-primed, Drying time and curing will affect the
dependent upon the soundness of the substrate but recommend priming with 330 Optima All performance of the product. Do not apply
to which it is applied. It has been determined Prime, 531 Tropicoat Quick Prime or 532 when air, surface or product temperatures are
that as high as 80% of all paint and coating Weathermaster Wood Prime. Bleeding woods below 50掳 F. or above 100掳 F. Surface
failures may be attributed to improper surface may require two coats of primer. temperature must be at least 5掳 F. above dew
preparation. It is essential that the proper steps point. Plan ahead and avoid applying when
New Plywood and Cured, Moisture-Free
be taken before applying this product. damp or threatening weather is expected.
Pressure Treated Wood: Prime with 330 Optima
Product must cure at least 8 hours before being
General: All Prime.
subjected to moisture. During extremely warm
Surface must be completely dry and in sound Previously Painted Wood: Prime with 330 weather, maintaining a wet edge may become
condition. Surface should be clean and free Optima All Prime, 531 Tropicoat Quick Prime difficult. Avoid application during the heat of
from dirt, grease, mill oils, form release agents, or 532 Weathermaster Wood Prime. Surfaces the day. During cool weather, be aware of
rust, mill scale, chalky paint, efflorescence, in good condition may be self primed when possible surfactant leaching. Do not apply late
organic growth, mildew, and foreign matter properly prepared. in the day where dew or condensation may
to insure good adhesion of primers and/or
New Ferrous Metal and Rusted Metal: Remove form before product begins to cure. Allow this
finish coats. Peeling, cracking, and
all rust and mill scale then prime with 635 Line product to cure a minimum of 30 days before
chipping paint should be removed by
Ironize Inhibitive Primer or 1635 Line Aquatec cleaning.
sandblasting, power tool cleaning, hand
Waterborne Industrial Primer.
tool cleaning, pressure washing, scraping, Safety
New Galvanized Metal and Aluminum:
or wire brushing. All glossy surfaces should
WARNING! HARMFUL IF INHALED. SEE
Clean per SSPC-SP1 Solvent Cleaning or use a
be sanded or de-glossed. Feather sand
LABEL OR MSDS FOR LIST OF HAZARDOUS
degreasing cleaner. Wipe clean with lint free
rough edges of previously painted surfaces
INGREDIENTS. KEEP OUT OF REACH OF
cloth. All mill oils must be removed. Neutralize
and spot prime bare areas. Any deteriorated
CHILDREN! May cause eye, skin, nose and
with vinegar or appropriate wash primer.
or failed sealant and/or patching compound
throat irritation. To avoid breathing vapors or
Rinse thoroughly, then prime with 330 Optima
should be removed and replaced. All
spray mist, open windows and doors or use
All Prime or 1635 Line Aquatec Waterborne
unpainted substrates should be properly
other means to insure fresh air entry during
Industrial Primer.
prepared according to respective
application and drying. If you experience eye
Previously Painted Metals: Prime with 635
manufacturer鈥檚 and/or supplier鈥檚
watering, headaches or dizziness, increase fresh
Line Ironize Inhibitive Primer, 330 Optima All
recommendations. Thoroughly review and
air or wear respiratory protection (NIOSH/
Prime or 1635 Line Aquatec Waterborne
follow Color Wheel 鈥淪urface Preparation
MSHA TC 23C or equivalent) or leave area.
Industrial Primer. Surfaces in good condition
Guidelines鈥? and/or Color Wheel written
Close container after each use. Avoid contact
may be self primed when properly prepared.
specification before applying.
with eyes and skin.
Recommended Primers General Application
First Aid
New Concrete and Masonry Surfaces: Mix thoroughly to a uniform consistency before
If you experience difficulty in breathing, leave
Allow a minimum of three (3) days of cure time each use. Apply by brush, roller or airless
the area to obtain fresh air. If continued difficulty
for new masonry, a seven (7) day cure time for sprayer. Work material vigorously into pores.
is experienced, get medical assistance
poured in place concrete and a pH level of 13 Maintain a wet edge. If roller application is
immediately. In case of eye contact, flush
or lower prior to application of product. Coatings employed on porous surfaces, final passes
immediately with large amounts of fresh water
have a greater resistance against failure when should be completed in a downward direction
for at least 15 minutes and get medical attention;
applied to a surface with a lower alkaline level to insure a uniform appearance and texture.
for skin, wash thoroughly with soap and water.
(below 8.5). Apply at such a rate as to avoid runs and sags.
If swallowed, DO NOT INDUCE VOMITING.
Prime high alkaline surfaces with 1252 Quick If airless spray application is employed on
Get medical attention immediately.
Cure Acrylic Conditioner (as per instructions porous surfaces, immediate 鈥渂ack rolling鈥? and
on data sheet), 1240 Flex Lox Exterior Coating, 鈥渂ack brushing鈥? with wet roller/brush is Storage and Handling
330 Optima All Prime or 335 Tropicoat Masonry recommended to help reduce pinholing and
Keep from freezing or exposure to intense heat.
Primer. Prime non-alkaline surfaces with 1240 work material into pores.
Do not transfer contents to unlabeled container.
Flex Lox Exterior Coating, 330 Optima All
Thinning:
Prime, 335 Tropicoat Masonry Primer or self
Technical Services
Under normal conditions thinning is not
prime. Prime porous masonry with 250 Ti-
recommended. Color Wheel Paints and Coatings offers and
Gard Masonry Filler or 3250 Hi-Build Block
Clean-Up: encourages the use of our free technical
Filler.
Clean all tools and equipment with warm, service. We also advise you to contact us
Previously Painted Masonry and Stucco: Prime
soapy water immediately after use. Flush spray regularly for updates to this and other
chalky surfaces with 950 Ti-Gard Conditioner,
equipment thoroughly. technical data. For technical assistance, to
1250 Ti-Gard Latex Conditioner or 1252 Quick
arrange a consultation with a Sales
Application Equipment
Cure Acrylic Conditioner. Surfaces in good
Representative, or for current technical data,
condition may be self primed when properly
Brush: Use a quality nylon or polyester brush. consult your yellow pages for the Color
prepared.
Wheel location nearest you, or call toll free
Roller: Use lambswool or synthetic cover:
Synthetic Masonry Stucco (EIFS): Prime with (800) 749-6810.
3/8" to 1 1/4" nap, depending on surface texture.
330 Optima All Prime, 1250 Ti-Gard Latex
Airless Spray: Use a tip size of between 0.015"
Conditioner or 1252 Quick Cure Acrylic
and 0.021". Tip size should reflect equipment
Conditioner. Surfaces in good condition may
type and pressure, applicator technique and
be self primed when properly prepared.
surface conditions. Adjust pressure for constant
and proper atomization.
All technical advice, recommendations, and services are rendered by Color Wheel gratis. They are based on technical data which Color Wheel believes to be reliable, and are intended for use by persons having skill and knowhow at their own discretion and risk.
Color Wheel Paint Manufacturing Company, Inc. assumes no responsibility for results obtained or damages incurred from their use by purchaser/user in whole or in part. All information is subject to change without notice.
NOTE: Where applicable, and for consistency, technical data and test results contained in this document are based on the pure white base of the particular product line.
LIMITATION OF LIABILITY: COLOR WHEEL MAKES NO WARRANTY OR GUARANTEE OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. UNLESS THE PRODUCT YOU PURCHASE INCLUDES A WRITTEN LIMITED WARRANTY, LIABILITY OF COLOR WHEEL,
IF ANY, IS LIMITED TO THE REPLACEMENT OF THE PRODUCT OR REFUND OF THE PURCHASE PRICE. LABOR AND COST OF LABOR AND OTHER INDIRECT, SPECIAL OR CONSEQUENTIAL DAMAGES ARE HEREBY EXCLUDED. USER IS RESPONSIBLE TO DETERMINE SUITABILITY OF PRODUCT FOR INTENDED USE.
09900 1240.04.7 / PDS / 2
|