PRODUCT DATA
1250
Ti-Gard Latex Conditioner
CONTRACTOR鈥橲 CHOICE 鈥? PROPRIETARY ACRYLIC 鈥? EXT 鈥? 1250 LINE
Vehicle Type
Product Description Waterborne 鈥? Proprietary Acrylic
Ti-Gard Latex Conditioner is a premium quality exterior water based
Finish
surface conditioner designed for use in residential, architectural,
Flat 鈥? 85掳 Sheen - 1.0 to 5.0
commercial and light industrial applications on a variety of properly
Use
prepared previously painted concrete and masonry and previously painted
Exterior
metal surfaces to bind light chalk (oxidation). Ti-Gard is also recommended
for use on cured concrete and masonry surfaces as a primer and may be
Percent Solids By Weight
used on interior plaster and gypsum board as a primer under wall 28.2% 卤 2%
coverings.
Percent Solids By Volume
19.5% 卤 2%
Performance
鈥? Remarkable resistance to blistering, cracking, chipping and peeling Suggested Coverage
300-500 SFPG
鈥? Excellent adhesion
鈥? Low odor
Dry Film Thickness
鈥? Rapid dry 1.0 mils @ 300 SFPG
May be applied to properly prepared... Viscosity
70 KU 卤 5
鈥? Cured and Uncured Masonry and Stucco including:
Cement Plaster 鈥? Poured and Precast Concrete Flash Point
鈥?
鈥? Previously Painted Surfaces including: Non-flammable 鈥? >200掳 F.
鈥? Masonry and Stucco 鈥? Wood
VOC
鈥? Ferrous Metals 鈥? Aluminum 鈥? Galvanized Metals
Contains .63 lbs./gal. (75 gms./ltr.)
Complies with all Federal, State
Specification Standards and Local VOC standards.
鈥? Performance alternate for Federal Specification: TT-P-620C Application Equipment
鈥? Meets or exceeds Florida Department of Education Standard Brush, roller, airless or
conventional spray
MP-14.2
Drying Time
Limitations
At 75掳F. / 50% RH
1 hour to touch
Not for use on Driveways, Garage Floors, Walkways or other foot or
4 hours to recoat
vehicle traffic areas. Do not apply below grade, where hydrostatic
pressure is expected, where a failure from water intrusion may occur Colors
(decorative, planter or perimeter walls) or to substrates constantly in White (1250), Clear (1251)
contact with moisture. Do not use in highly corrosive or chemical
Products included in this line
environments, or areas subject to intense heat.
1250 - White
1251 - Clear
COLOR WHEEL PAINT MANUFACTURING COMPANY, INC.
Product Index 鈥? Category 3
2814 Silver Star Road 鈥? Orlando, Florida 32808
Exterior Primers, Sealers
407-293-6810 鈥? 800-749-6810 鈥? Fax 407-293-0945
www.colorwheelpaint.com & Conditioners
09900
2001.1 / PDS / 1
1250 LINE TI-GARD LATEX CONDITIONER 鈥? CONTRACTOR鈥橲 CHOICE 鈥? PROPRIETARY ACRYLIC 鈥? EXTERIOR 鈥? PRIMER
Surface Preparation General Application Safety
The performance of this product is critically Mix thoroughly to a uniform consistency before WARNING! HARMFUL IF INHALED. SEE
dependent upon the soundness of the substrate each use. Apply by brush, roller or airless LABEL OR MSDS FOR LIST OF HAZARDOUS
to which it is applied. It has been determined sprayer. Work material vigorously into pores. INGREDIENTS. KEEP OUT OF REACH OF
that as high as 80% of all paint and coating Maintain a wet edge. If roller application is CHILDREN! May cause eye, skin, nose and
failures may be attributed to improper surface employed on porous surfaces, final passes throat irritation. To avoid breathing vapors
preparation. It is essential that the proper steps should be completed in a downward direction or spray mist, open windows and doors or
be taken before applying this product. to insure a uniform appearance and texture. use other means to insure fresh air entry
Apply at such a rate as to avoid runs and sags. during application and drying. If you
General:
If airless spray application is employed on experience eye watering, headaches or
Surface must be completely dry and in sound
porous surfaces, immediate 鈥渂ack rolling鈥? and dizziness, increase fresh air or wear
condition. Surface should be clean and free
鈥渂ack brushing鈥? with wet roller/brush is respiratory protection (NIOSH/MSHA TC 23C
from dirt, grease, mill oils, rust, mill scale,
recommended to help reduce pinholing and or equivalent) or leave area. Close container
chalky paint, efflorescence, organic growth,
work material into pores. after each use. Avoid contact with eyes and
mildew, and foreign matter to insure good
skin.
adhesion of primers and/or finish coats. Thinning:
First Aid
Peeling, cracking, and chipping paint Under normal conditions thinning is not
should be removed by sandblasting, power recommended. If you experience difficulty in breathing,
tool cleaning, hand tool cleaning, pressure Clean-Up: leave the area to obtain fresh air. If continued
washing, scraping, or wire brushing. All Clean all tools and equipment with warm, difficulty is experienced, get medical
glossy surfaces should be sanded or soapy water immediately after use. Flush spray assistance immediately. In case of eye
de-glossed. Feather sand rough edges of equipment thoroughly. contact, flush immediately with large
previously painted surfaces and spot prime Application Equipment amounts of fresh water for at least 15 minutes
bare areas. Any deteriorated or failed sealant and get medical attention; for skin, wash
Brush: Use a quality nylon or polyester brush.
and/or patching compound should be thoroughly with soap and water. If
Roller: Use lambswool or synthetic cover:
removed and replaced. All unpainted swallowed, DO NOT INDUCE VOMITING.
3/8" to 1 1/4" nap, depending on surface texture.
substrates should be properly prepared Get medical attention immediately.
Airless Spray: Use a tip size of between 0.015"
according to respective manufacturer鈥檚 and/or
Storage and Handling
and 0.021". Tip size should reflect equipment
supplier鈥檚 recommendations. Thoroughly
type and pressure, applicator technique and Keep from freezing or exposure to intense
review and follow Color Wheel 鈥淪urface
surface conditions. Adjust pressure for constant heat. Do not transfer contents to unlabeled
Preparation Guidelines鈥? and/or Color Wheel
and proper atomization. container.
written specification before applying.
Curing Technical Services
Drying time and curing will affect the Color Wheel Paints and Coatings offers
performance of the product. Do not apply and encourages the use of our free
when air, surface or product temperatures are technical service. We also advise you to
below 50藲 F. or above 100藲 F. Surface contact us regularly for updates to this
temperature must be at least 5藲 F. above dew and other technical data. For technical
point. Plan ahead and avoid applying when assistance, to arrange a consultation with
damp or threatening weather is expected. a Sales Representative, or for current
Product must cure at least 8 hours before being technical data, consult your yellow pages
subjected to moisture. During extremely warm for the Color Wheel location nearest you,
weather, maintaining a wet edge may become or call toll free (800) 749-6810.
difficult. Avoid application during the heat of
the day. During cool weather, be aware of
possible surfactant leaching. Do not apply late
in the day where dew or condensation may
form before product begins to cure. Allow this
product to cure a minimum of 30 days before
cleaning.
All technical advice, recommendations, and services are rendered by Color Wheel gratis. They are based on technical data which Color Wheel believes to be reliable, and are intended for use by persons having skill and knowhow at their own discretion and risk.
Color Wheel Paint Manufacturing Company, Inc. assumes no responsibility for results obtained or damages incurred from their use by purchaser/user in whole or in part. All information is subject to change without notice.
NOTE: Where applicable, and for consistency, technical data and test results contained in this document are based on the pure white base of the particular product line.
LIMITATION OF LIABILITY: COLOR WHEEL MAKES NO WARRANTY OR GUARANTEE OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
Liability, if any, is limited to replacement of the product or refund of the purchase price. LABOR OR COST OF LABOR AND OTHER CONSEQUENTIAL DAMAGES ARE HEREBY EXCLUDED.
09900 2001.1 / PDS / 2
|