PRODUCT DATA
1270
Flex Lox Exterior Satin Coating
PREMIUM 鈥? 100% ACRYLIC 鈥? EXTERIOR 鈥? SATIN 鈥? 1270 LINE
Product Description Vehicle Type
Waterborne 鈥? 100% Acrylic
Flex Lox Exterior Satin Coating is a superior quality, flexible coating
formulated with an exceptional blend of premium durable 100% acrylic
Finish
resins for use as a primer or finish coat. The addition of zinc oxide Satin 鈥? 60掳 Gloss - 4.0 to 8.0
combined with organic mildewcides give Flex Lox Exterior Satin Coating 鈥? 85掳 Sheen - 30 to 40
excellent protection against mildew. The formulation of Flex Lox Exterior
Use
Satin Coating gives it a high resistance to alkali and efflorescence which
Exterior
makes it an excellent primer for new stucco and low density masonry
block. Flex Lox Exterior Satin Coating is designed for use in residential, Percent Solids By Weight
architectural, commercial and light industrial applications on various 58.5% 卤 2%
substrates.
Percent Solids By Volume
Performance 44.0% 卤 2%
鈥? Excellent primer for new stucco and low density masonry block Suggested Coverage
鈥? Exceptional resistance to alkali and efflorescence 200 SFPG
(depending on porosity and DFT)
鈥? Excellent for use as a satin finish coat
鈥? Allows moisture vapor transmission Dry Film Thickness
鈥? Easy to apply, high build formulation for excellent coverage 3.6 mils @ 200 SFPG
(custom DFT's can be specified)
鈥? Excellent color retention and chalk resistance
Nonporous surfaces like metal, wood etc.
鈥? Extremely durable and flexible with excellent adhesion do not require a high DFT.
鈥? Bridges hairline cracks
Viscosity
鈥? Excellent resistance to mildew and organic growth
108 KU 卤 5
鈥? Excellent resistance to blistering, cracking, chipping and peeling
Flash Point
May be applied to properly primed and prepared鈥? Nonflammable 鈥? >200掳 F.
鈥? Concrete, Masonry and Stucco including:
VOC
Brick , Cement Plaster, Poured and Precast Concrete, Contains .64 lbs./gal. (77 gms./ltr.)
Complies with all Federal, State
Concrete Masonry Units (CMU), Cementitious Siding
and Local VOC standards.
鈥? Synthetic Masonry Stucco (EIFS)
鈥? Wood, Plywood, Hardboard and Gypsum Wallboard Application Equipment
鈥? Brush, roller, airless or
Aluminum, Galvanized Metals and Ferrous Metal
conventional spray
Specification Standards
Drying Time
Performance alternate for Federal Specification TT-P-19D; TT-P-96D At 75掳F. / 50% RH
Exceeds Federal Specification for resistance to wind driven rain: TT-C-555B 1 hour to touch
4 hours to recoat
section 3.3.3 - 98 m.p.h. Wind Driven Test.
Passes ASTM D2370 - 350% Elongation at Break / 200 psi Tensile Strength.
Colors
White and off whites
Limitations
Products Included in This Line
Allow a minimum of three (3) days of cure time for new masonry, a seven
1270 - White
(7) day cure time for poured in place concrete and a pH level of 13 or lower
prior to application of product. Coatings have a greater resistance against
failure when applied to a surface with a pH level near 8.5. Not
recommended for steps, walkways, or other foot or vehicle traffic areas.
Do not use for immersion service, below grade substrates, or substrates
constantly in contact with moisture. Do not use in highly corrosive or
chemical environments, or areas subject to intense heat.
COLOR WHEEL PAINTS AND COATINGS
Product Index 鈥? Category 1
2814 Silver Star Road 鈥? Orlando, Florida 32808
407-293-6810 鈥? 800-749-6810 鈥? Fax 407-293-0945
Exterior Paints & Coatings
www.colorwheel.com
09900
1270.04.1 / PDS / 1
1270 LINE FLEX LOX EXTERIOR SATIN COATING 鈥? PREMIUM 鈥? 100% ACRYLIC 鈥? EXTERIOR 鈥? SATIN
Surface Preparation Recommended Primers (continued) Curing
The performance of this product is critically New Wood and Hardboard: Can be self-primed, Drying time and curing will affect the
dependent upon the soundness of the substrate but recommend priming with 330 Optima All performance of the product. Do not apply
to which it is applied. It has been determined Prime, 531 Tropicoat Quick Prime or 532 when air, surface or product temperatures are
that as high as 80% of all paint and coating Weathermaster Wood Prime. Bleeding woods below 50掳 F. or above 100掳 F. Surface
failures may be attributed to improper surface may require two coats of primer. temperature must be at least 5掳 F. above dew
preparation. It is essential that the proper steps point. Plan ahead and avoid applying when
New Plywood and Cured, Moisture-Free
be taken before applying this product. damp or threatening weather is expected.
Pressure Treated Wood: Prime with 330 Optima
Product must cure at least 8 hours before being
General: All Prime.
subjected to moisture. During extremely warm
Surface must be completely dry and in sound Previously Painted Wood: Prime with 330 weather, maintaining a wet edge may become
condition. Surface should be clean and free Optima All Prime, 531 Tropicoat Quick Prime difficult. Avoid application during the heat of
from dirt, grease, mill oils, form release agents, or 532 Weathermaster Wood Prime. Surfaces the day. During cool weather, be aware of
rust, mill scale, chalky paint, efflorescence, in good condition may be self primed when possible surfactant leaching. Do not apply late
organic growth, mildew, and foreign matter properly prepared. in the day where dew or condensation may
to insure good adhesion of primers and/or
New Ferrous Metal and Rusted Metal: Remove form before product begins to cure. Allow this
finish coats. Peeling, cracking, and
all rust and mill scale then prime with 635 Line product to cure a minimum of 30 days before
chipping paint should be removed by
Ironize Inhibitive Primer or 1635 Line Aquatec cleaning.
sandblasting, power tool cleaning, hand
Waterborne Industrial Primer.
tool cleaning, pressure washing, scraping, Safety
New Galvanized Metal and Aluminum:
or wire brushing. All glossy surfaces should
WARNING! HARMFUL IF INHALED. SEE
Clean per SSPC-SP1 Solvent Cleaning or use a
be sanded or de-glossed. Feather sand
LABEL OR MSDS FOR LIST OF HAZARDOUS
degreasing cleaner. Wipe clean with lint free
rough edges of previously painted surfaces
INGREDIENTS. KEEP OUT OF REACH OF
cloth. All mill oils must be removed. Neutralize
and spot prime bare areas. Any deteriorated
CHILDREN! May cause eye, skin, nose and
with vinegar or appropriate wash primer.
or failed sealant and/or patching compound
throat irritation. To avoid breathing vapors or
Rinse thoroughly, then prime with 330 Optima
should be removed and replaced. All
spray mist, open windows and doors or use
All Prime or 1635 Line Aquatec Waterborne
unpainted substrates should be properly
other means to insure fresh air entry during
Industrial Primer.
prepared according to respective
application and drying. If you experience eye
Previously Painted Metals: Prime with 635
manufacturer鈥檚 and/or supplier鈥檚
watering, headaches or dizziness, increase fresh
Line Ironize Inhibitive Primer, 330 Optima All
recommendations. Thoroughly review and
air or wear respiratory protection (NIOSH/
Prime or 1635 Line Aquatec Waterborne
follow Color Wheel 鈥淪urface Preparation
MSHA TC 23C or equivalent) or leave area.
Industrial Primer. Surfaces in good condition
Guidelines鈥? and/or Color Wheel written
Close container after each use. Avoid contact
may be self primed when properly prepared.
specification before applying.
with eyes and skin.
Recommended Primers General Application
First Aid
New Concrete and Masonry Surfaces: Mix thoroughly to a uniform consistency before
If you experience difficulty in breathing, leave
Allow a minimum of three (3) days of cure time each use. Apply by brush, roller or airless
the area to obtain fresh air. If continued difficulty
for new masonry, a seven (7) day cure time for sprayer. Work material vigorously into pores.
is experienced, get medical assistance
poured in place concrete and a pH level of 13 Maintain a wet edge. If roller application is
immediately. In case of eye contact, flush
or lower prior to application of product. Coatings employed on porous surfaces, final passes
immediately with large amounts of fresh water
have a greater resistance against failure when should be completed in a downward direction
for at least 15 minutes and get medical attention;
applied to a surface with a lower alkaline level to insure a uniform appearance and texture.
for skin, wash thoroughly with soap and water.
(below 8.5). Apply at such a rate as to avoid runs and sags.
If swallowed, DO NOT INDUCE VOMITING.
Prime high alkaline surfaces with 1252 Quick If airless spray application is employed on
Get medical attention immediately.
Cure Acrylic Conditioner (as per instructions porous surfaces, immediate 鈥渂ack rolling鈥? and
on data sheet), 1240 Flex Lox Exterior Coating, 鈥渂ack brushing鈥? with wet roller/brush is Storage and Handling
1270 Flex Lox Exterior Satin Coating, 330 recommended to help reduce pinholing and
Keep from freezing or exposure to intense heat.
Optima All Prime or 335 Tropicoat Masonry work material into pores.
Do not transfer contents to unlabeled container.
Primer. Prime non-alkaline surfaces with 1240
Thinning:
Flex Lox Exterior Coating, 1240 Flex Lox Exterior
Technical Services
Under normal conditions thinning is not
Satin Coating, 330 Optima All Prime, 335
recommended. Color Wheel Paints and Coatings offers and
Tropicoat Masonry Primer or self prime. Prime
Clean-Up: encourages the use of our free technical
porous masonry with 250 Ti-Gard Masonry
Clean all tools and equipment with warm, service. We also advise you to contact us
Filler or 3250 Hi-Build Block Filler.
soapy water immediately after use. Flush spray regularly for updates to this and other
Previously Painted Masonry and Stucco: Prime
equipment thoroughly. technical data. For technical assistance, to
chalky surfaces with 950 Ti-Gard Conditioner,
arrange a consultation with a Sales
Application Equipment
1250 Ti-Gard Latex Conditioner or 1252 Quick
Representative, or for current technical data,
Cure Acrylic Conditioner. Surfaces in good
Brush: Use a quality nylon or polyester brush. consult your yellow pages for the Color
condition may be self primed when properly
Wheel location nearest you, or call toll free
Roller: Use lambswool or synthetic cover:
prepared.
(800) 749-6810.
3/8" to 1 1/4" nap, depending on surface texture.
Synthetic Masonry Stucco (EIFS): Prime with
Airless Spray: Use a tip size of between 0.015"
330 Optima All Prime, 1250 Ti-Gard Latex
and 0.021". Tip size should reflect equipment
Conditioner or 1252 Quick Cure Acrylic
type and pressure, applicator technique and
Conditioner. Surfaces in good condition may
surface conditions. Adjust pressure for constant
be self primed when properly prepared.
and proper atomization.
All technical advice, recommendations, and services are rendered by Color Wheel gratis. They are based on technical data which Color Wheel believes to be reliable, and are intended for use by persons having skill and knowhow at their own discretion and risk.
Color Wheel Paint Manufacturing Company, Inc. assumes no responsibility for results obtained or damages incurred from their use by purchaser/user in whole or in part. All information is subject to change without notice.
NOTE: Where applicable, and for consistency, technical data and test results contained in this document are based on the pure white base of the particular product line.
LIMITATION OF LIABILITY: COLOR WHEEL MAKES NO WARRANTY OR GUARANTEE OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. UNLESS THE PRODUCT YOU PURCHASE INCLUDES A WRITTEN LIMITED WARRANTY, LIABILITY OF COLOR WHEEL,
IF ANY, IS LIMITED TO THE REPLACEMENT OF THE PRODUCT OR REFUND OF THE PURCHASE PRICE. LABOR AND COST OF LABOR AND OTHER INDIRECT, SPECIAL OR CONSEQUENTIAL DAMAGES ARE HEREBY EXCLUDED. USER IS RESPONSIBLE TO DETERMINE SUITABILITY OF PRODUCT FOR INTENDED USE.
09900 1270.04.1 / PDS / 2
|