PRODUCT DATA
3823
Ultracrete Hydrostain Clear Coat
PROPRIETARY ACRYLIC 鈥? INTERIOR / EXTERIOR 鈥? GLOSS 鈥? 3823
Vehicle Type
Product Description Waterborne 鈥? Proprietary Acrylic
Ultracrete Hydrostain Clear Coat is a superior quality interior/exterior
Finish
proprietary acrylic latex high gloss clear coat designed for use in residential,
Gloss 鈥? 60掳 Gloss - 75 to 85
architectural and commercial and light industrial applications as a top
coat over siliconized concrete stain or as a sealer over a variety of properly Use
prepared finished or unfinished concrete and masonry surfaces. Interior / Exterior
Performance Percent Solids By Weight
34.7% 卤 2%
鈥? Excellent adhesion
鈥? Exceptional long term durability Percent Solids By Volume
32.0% 卤 2%
鈥? Excellent color and gloss retention
鈥? Remarkable resistance to blistering, cracking, chipping and peeling
Suggested Coverage
鈥? Easy to apply
300-500 SFPG
鈥? Scrubbable and washable
鈥? Good flow and leveling properties Dry Film Thickness
鈥? 1.3 mils @ 400 SFPG
Good stain removal properties
鈥? Resistant to moisture and moisture vapor
Viscosity
鈥? Resistant to staining
Less than 45 KU
May be applied to properly prepared... Flash Point
Non-flammable 鈥? >200掳 F.
鈥? Concrete walkways
鈥? Concrete patios
VOC
鈥? Concrete pool decks Contains 1.1 lbs./gal. (132 gms./ltr.)
鈥? Brick Complies with all Federal, State
and Local VOC standards.
鈥? Decorative block
Application Equipment
Limitations
Brush, roller, airless or
conventional spray
Do not apply to damp surfaces. Do not use on garage floors. Do not use
for immersion service, below grade substrates, or substrates constantly in
Drying Time
contact with moisture. Do not use in highly corrosive or chemical
At 75掳F. / 50% RH
environments, or areas subject to intense heat. 1 hour to touch
2 hours to recoat
Note: Always select and apply a test area if unfamiliar with surface or
Colors
product. User and owner should be aware that non-porous damp, soiled Clear
or incline surfaces may become quite slippery. Determine whether or not
Products included in this line
a slip resistant additive should be added to stain before application.
3823 - Clear
COLOR WHEEL PAINT MANUFACTURING COMPANY, INC.
Product Index 鈥? Category 7
2814 Silver Star Road 鈥? Orlando, Florida 32808
407-293-6810 鈥? 800-749-6810 鈥? Fax 407-293-0945
Floor Finishes & Concrete Stains
www.colorwheelpaint.com
09900
2001.1 / PDS / 1
3823 ULTRACRETE HYDROSTAIN CLEAR COAT 鈥? PROPRIETARY ACRYLIC 鈥? INTERIOR / EXTERIOR 鈥? GLOSS
Surface Preparation Curing
New Concrete Surfaces: (continued)
Mix thoroughly to a uniform consistency before
The performance of this product is critically Drying time and curing will affect the
each use. Apply a thin even first coat to all
dependent upon the soundness of the substrate performance of the product. Do not apply
surfaces receiving finish materials (avoid build
to which it is applied. It has been determined when air, surface or product temperatures
up, penetration to substrate is main objective).
that as high as 80% of all paint and coating are below 50藲 F. or above 100藲 F. Surface
Coverage rate varies greatly with porosity of
failures may be attributed to improper surface temperature must be at least 5藲 F. above dew
surface being coated. Allow twelve hours
preparation. It is essential that the proper steps point. Plan ahead and avoid applying when
curing time before applying second coat.
be taken before applying this product. damp or threatening weather is expected.
Second coat will be a normal application.
Product must cure at least 24 hours before
General: New Wood Surfaces: being subjected to moisture. During
Surface must be completely dry and in sound Mix thoroughly to a uniform consistency before extremely warm weather, maintaining a wet
condition. Surface should be clean and free each use. Apply a thin even first coat to all edge may become difficult. Avoid application
from dirt, grease, mill oils, rust, mill scale, surfaces receiving finish materials (avoid build during the heat of the day. During cool
chalky paint, efflorescence, organic growth, up, penetration to substrate is main objective). weather, be aware of possible surfactant
mildew, and foreign matter to insure good Coverage rate varies greatly with porosity of leaching. Do not apply late in the day where
adhesion of primers and/or finish coats. Peeling, surface being coated. Allow twelve hours dew or condensation may form before
cracking, and chipping paint should be removed curing time before applying second coat. product begins to cure. Allow this product to
by sandblasting, power tool cleaning, hand Second coat will be a normal application. cure a minimum of 30 days before cleaning.
tool cleaning, pressure washing, scraping, or
Previously Painted Surfaces: Safety
wire brushing. All glossy surfaces should be
See Surface Preparation section.
sanded or de-glossed. Feather sand rough edges
WARNING! HARMFUL IF INHALED.
of previously painted surfaces and spot prime
General Application SEE LABEL OR MSDS FOR LIST OF
bare areas. Any deteriorated or failed sealant
HAZARDOUS INGREDIENTS. KEEP OUT
and/or patching compound should be removed Mix thoroughly to a uniform consistency before
OF REACH OF CHILDREN! May cause eye,
and replaced. All unpainted substrates each use. Apply by brush, roller or airless
skin, nose and throat irritation. To avoid
should be properly prepared according sprayer. Work material vigorously into pores.
breathing vapors or spray mist, open windows
to respective manufacturer鈥檚 and / or Maintain a wet edge. If roller application is
and doors or use other means to ensure fresh
supplier鈥檚 recommendations. Thoroughly employed on porous surfaces, final passes
air entry during application and drying. If
review and follow Color Wheel 鈥淪urface should be completed in a downward direction
you experience eye watering, headaches or
Preparation Guidelines鈥? and/or Color Wheel to insure a uniform appearance and texture.
dizziness, increase fresh air or wear
written specification before applying. Apply at such a rate as to avoid runs and sags.
respiratory protection (NIOSH/MSHA TC 23C
If airless spray application is employed on
Recommended Primer/Application or equivalent) or leave area. Close container
porous surfaces, immediate 鈥渂ack rolling鈥? and
after each use. Avoid contact with eyes and
鈥渂ack brushing鈥? with wet roller/brush is
New Concrete Surfaces:
skin.
The Florida Concrete & Products Association recommended to help reduce pinholing and
First Aid
recommends that a curing time of no less than work material into pores.
30 days should be observed before painting
Thinning: If you experience difficulty in breathing,
new concrete surfaces. Floors should always
Under normal conditions thinning is not leave the area to obtain fresh air. If continued
be tested for moisture prior to commencement
recommended. difficulty is experienced, get medical
of work. Surface should be clean and free of
assistance immediately. In case of eye
Clean-Up:
any foreign matter that may affect the adhesion
contact, flush immediately with large
Clean all tools and equipment with warm,
and performance of the finish coat and at a safe
amounts of fresh water for at least 15 minutes
soapy water immediately after use. Flush spray
level of pH (below 8.5).
and get medical attention; for skin, wash
equipment thoroughly.
Non-Porous (trowel finish) concrete should be thoroughly with soap and water. If
Application Equipment
acid etched with 1 part muriatic acid to 8 parts swallowed, DO NOT INDUCE VOMITING.
water. Test mixture to insure proper profile, Get medical attention immediately.
Brush: Use a quality nylon or polyester brush.
between 1.5 and 2.0, is obtained. A stronger
Storage and Handling
mixture may be needed. Apply evenly to all Roller: Use lambswool or synthetic cover: 1/4"
areas. Using a course nylon bristle brush, scrub to 3/4" nap, depending on surface texture. Keep from freezing or exposure to intense
all areas. Allow to remain for 10 to 15 minutes.
heat. Do not transfer contents to unlabeled
Airless Spray: Use a tip size of between 0.015"
Using a pressure washer, rinse thoroughly to
container.
and 0.021". Tip size should reflect equipment
insure all residue has been removed. A second
type and pressure, applicator technique and
Technical Services
or third thorough rinse maybe needed to ensure
surface conditions. Adjust pressure for constant
all residue has been removed. Failure to
and proper atomization. Color Wheel Paints and Coatings offers and
properly etch and completely rinse the surface
encourages the use of our free technical
clean could result in adhesion problems. Allow
service. We also advise you to contact us
twenty-four hours drying time before coating.
regularly for updates to this and other
technical data. For technical assistance, to
arrange a consultation with a Sales
Representative, or for current technical data,
consult your yellow pages for the Color
Wheel location nearest you, or call toll free
(800) 749-6810.
All technical advice, recommendations, and services are rendered by Color Wheel gratis. They are based on technical data which Color Wheel believes to be reliable, and are intended for use by persons having skill and knowhow at their own discretion and risk.
Color Wheel Paint Manufacturing Company, Inc. assumes no responsibility for results obtained or damages incurred from their use by purchaser/user in whole or in part. All information is subject to change without notice.
NOTE: Where applicable, and for consistency, technical data and test results contained in this document are based on the pure white base of the particular product line.
LIMITATION OF LIABILITY: COLOR WHEEL MAKES NO WARRANTY OR GUARANTEE OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
Liability, if any, is limited to replacement of the product or refund of the purchase price. LABOR OR COST OF LABOR AND OTHER CONSEQUENTIAL DAMAGES ARE HEREBY EXCLUDED.
09900 2001.1 / PDS / 2
|