PRODUCT DATA
200i
Hi-Hide Interior Latex Wall Paint
CONTRACTOR鈥橲 CHOICE 鈥? INTERIOR 鈥? FLAT 鈥? 200i LINE
Vehicle Type
Product Description Waterborne 鈥? Latex
Hi-Hide Interior Latex Wall Paint is a superior quality interior latex flat
Finish
paint recommended for use on a diverse number of properly prepared
Flat 鈥? 85掳 Sheen - 1.0 to 5.0
surfaces. Hi-Hide Interior Latex Wall Paint's extremely flat finish greatly
Use
aids in masking wall imperfections. Hi-Hide Interior Latex Wall Paint is
Interior
designed for use in residential, architectural and commercial applications.
Percent Solids By Weight
Performance 52.5% 卤 2%
鈥? Very high hiding
Percent Solids By Volume
鈥? Low odor 34.1% 卤 2%
鈥? Masks wall imperfections
Suggested Coverage
鈥? Outstanding touch up properties
300-500 SFPG
鈥? Non-yellowing
鈥? Extremely scrubbable and washable Dry Film Thickness
鈥? Extremely easy to apply 1.4 mils @ 400 SFPG
鈥? Soap and water cleanup
Viscosity
100 KU 卤 5
May be applied to properly primed and prepared鈥?
Flash Point
鈥? Concrete and Masonry Surfaces including:
Non-flammable 鈥? >200掳 F.
Cement Plaster Concrete Masonry Units (CMU)
鈥? 鈥?
VOC
Poured and Precast Concrete
鈥?
Contains .94 lbs./gal. (113 gms./ltr.)
鈥? Wood Surfaces including: Complies with all Federal, State
and Local VOC standards.
Paneling Plywood
鈥? 鈥?
鈥? Gypsum Wallboard 鈥? Gypsum Plaster and Veneer Plaster Application Equipment
鈥? Ferrous Metals 鈥? Aluminum 鈥? Galvanized Metals Brush, roller, airless or
conventional spray
Specification Standards
Drying Time
鈥? Performance alternate for Federal Specification: At 75掳F. / 50% RH
1 hour to touch
TT-P-29J, TT-P-1728A
4 hours to recoat
Limitations Colors
Ready mix colors, white, off
For interior use only. Not recommended for steps, walkways, or other foot whites, pastels, light and medium
colors
or vehicle traffic areas. Do not use for immersion service, below grade
substrates, or substrates constantly in contact with moisture. Do not use Products Included in This Line
in extremely corrosive or chemical environments, or areas subject to 200i - White and Factory Colors
204 - Bone
intense heat. 205 - Bone Tint
206 - Oyster
207 - Oyster Tint
210 - Popcorn
COLOR WHEEL PAINT MANUFACTURING COMPANY, INC.
Product Index 鈥? Category 4
2814 Silver Star Road 鈥? Orlando, Florida 32808
407-293-6810 鈥? 800-749-6810 鈥? Fax 407-293-0945
Interior Paints & Coatings
www.colorwheelpaint.com
09900
2001.1 / PDS / 1
200i LINE HI-HIDE INTERIOR LATEX WALL PAINT 鈥? CONTRACTOR'S CHOICE 鈥? INTERIOR 鈥? FLAT
Surface Preparation Recommended Primers (continued) Curing
The performance of this product is critically Previously Painted Masonry: Prime with 430 Drying time and curing will affect the
dependent upon the soundness of the substrate Ti-Gard Interior Sealer, 330 Optima All Prime, performance of the product. Do not apply
to which it is applied. It has been determined or 8300 Gloss Prep Waterborne Undercoat. when air, surface or product temperatures are
that as high as 80% of all paint and coating Surfaces in good condition may be self primed. below 50藲 F. or above 100藲 F. Surface
failures may be attributed to improper surface New Wood and Plywood: Prime with 830 temperature must be at least 5藲 F. above dew
preparation. It is essential that the proper steps Gloss Prep Undercoat, 831 Gloss Prep Fast Dry point. Plan ahead and avoid applying when
be taken before applying this product. Undercoat or 8300 Gloss Prep Waterborne damp or threatening weather is expected.
General: Undercoat. Bleeding woods may require two Product must cure at least 8 hours before being
Surface must be completely dry and in sound coats of primer. subjected to moisture. During extremely warm
condition. Surface should be clean and free weather, maintaining a wet edge may become
Previously Painted Wood: Prime with 830 Gloss
from dirt, grease, mill oils, rust, mill scale, difficult. Avoid application during the heat of
Prep Undercoat, 831 Gloss Prep Fast Dry
chalky paint, efflorescence, organic growth, the day. During cool weather, be aware of
Undercoat or 8300 Gloss Prep Waterborne
mildew, and foreign matter to insure good possible surfactant leaching. Do not apply late
Undercoat. Surfaces in good condition may be
adhesion of primers and/or finish coats. in the day where dew or condensation may
self primed.
Peeling, cracking, and chipping paint form before product begins to cure. Allow this
New Ferrous Metal and Rusted Metal: Remove
should be removed by sandblasting, power product to cure a minimum of 30 days before
all rust and mill scale then prime with 635 Line
tool cleaning, hand tool cleaning, pressure cleaning.
Ironize Inhibitive Primer or 1635 Line Aquatec
washing, scraping, or wire brushing. All
Safety
Waterborne Industrial Primer.
glossy surfaces should be sanded or
New Galvanized Metal and Aluminum: WARNING! HARMFUL IF INHALED. SEE
de-glossed. Feather sand rough edges of
Remove all mill oils with a non-petroleum LABEL OR MSDS FOR LIST OF HAZARDOUS
previously painted surfaces and spot prime
based solvent then prime with 330 INGREDIENTS. KEEP OUT OF REACH OF
bare areas. Any deteriorated or failed sealant
Optima All Prime or 1635 Line CHILDREN! May cause eye, skin, nose and
and/or patching compound should be
Aquatec Waterborne Industrial Primer. throat irritation. To avoid breathing vapors or
removed and replaced. All unpainted
Previously Painted Metals: Prime with 635 spray mist, open windows and doors or use
substrates should be properly prepared
Line Ironize Inhibitive Primer, 330 Optima All other means to insure fresh air entry during
according to respective manufacturer鈥檚 and/or
Prime or 1635 Line Aquatec Waterborne application and drying. If you experience eye
supplier鈥檚 recommendations. Thoroughly
Industrial Primer. Surfaces in good condition watering, headaches or dizziness, increase fresh
review and follow Color Wheel 鈥淪urface
may be self primed. air or wear respiratory protection (NIOSH/
Preparation Guidelines鈥? and/or Color Wheel
MSHA TC 23C or equivalent) or leave area.
written specification before applying. General Application
Close container after each use. Avoid contact
Recommended Primers Mix thoroughly to a uniform consistency before with eyes and skin.
New Textured Surfaces: Adding Color Wheel each use. Apply by brush, roller or airless
First Aid
460 Ti-Gard Dry Wall Texture Hardener to sprayer. Work material vigorously into pores.
spray wall texture (orange peel) prior to paint Maintain a wet edge. If roller application is If you experience difficulty in breathing, leave
application will greatly improve the washability employed on porous surfaces, final passes the area to obtain fresh air. If continued difficulty
of the finish coat If texture has already been should be completed in a downward direction is experienced, get medical assistance
applied without Texture Hardener, use priming to insure a uniform appearance and texture. immediately. In case of eye contact, flush
instructions below. Apply at such a rate as to avoid runs and sags. immediately with large amounts of fresh water
If airless spray application is employed on
New Interior Plaster and Gypsum Wallboard: for at least 15 minutes and get medical attention;
porous surfaces, immediate 鈥渂ack rolling鈥? and
Allow plaster to cure and be sure all drywall for skin, wash thoroughly with soap and water.
鈥渂ack brushing鈥? with wet roller/brush is
joint compound is thoroughly dry and cured. If swallowed, DO NOT INDUCE VOMITING.
recommended to help reduce pinholing and
Prime with 430 Ti-Gard Interior Sealer, 330 Get medical attention immediately.
work material into pores.
Optima All Prime, 830 Gloss Prep Undercoat,
Storage and Handling
831 Gloss Prep Fast Dry Undercoat, 8300 Thinning:
Keep from freezing or exposure to intense heat.
Gloss Prep Waterborne Undercoat or self prime. Under normal conditions thinning is not
Do not transfer contents to unlabeled container.
recommended.
Previously Painted Plaster and Wallboard:
Technical Services
Prime with 430 Ti-Gard Interior Sealer, 330 Clean-Up:
Optima All Prime, 830 Gloss Prep Undercoat, Clean all tools and equipment with warm, Color Wheel Paints and Coatings offers and
831 Gloss Prep Fast Dry Undercoat or 8300 soapy water immediately after use. Flush spray encourages the use of our free technical
Gloss Prep Waterborne Undercoat. Surfaces in equipment thoroughly. service. We also advise you to contact us
good condition may be self primed.
Application Equipment regularly for updates to this and other
New Concrete and Masonry : Prime alkaline technical data. For technical assistance, to
Brush: Use a quality nylon or polyester brush.
masonry (pH Range: 8-10) with 330 Optima All arrange a consultation with a Sales
Prime, 952 Fas-Gard Conditioner or 1252 Quick Roller: Use lambswool or synthetic cover: Representative, or for current technical data,
Cure Acrylic Conditioner. Prime non-alkaline 3/8" to 1 1/4" nap, depending on surface texture. consult your yellow pages for the Color
masonry with 430 Ti-Gard Interior Sealer, 330 Wheel location nearest you, or call toll free
Airless Spray: Use a tip size of between 0.015"
Optima All Prime, 8300 Gloss Prep Waterborne (800) 749-6810.
and 0.021". Tip size should reflect equipment
Undercoat or self prime. Prime porous masonry type and pressure, applicator technique and
with 250 Ti-Gard Masonry Filler or 3250 surface conditions. Adjust pressure for constant
Hi-Build Block Filler. and proper atomization.
All technical advice, recommendations, and services are rendered by Color Wheel gratis. They are based on technical data which Color Wheel believes to be reliable, and are intended for use by persons having skill and knowhow at their own discretion and risk.
Color Wheel Paint Manufacturing Company, Inc. assumes no responsibility for results obtained or damages incurred from their use by purchaser/user in whole or in part. All information is subject to change without notice.
NOTE: Where applicable, and for consistency, technical data and test results contained in this document are based on the pure white base of the particular product line.
LIMITATION OF LIABILITY: COLOR WHEEL MAKES NO WARRANTY OR GUARANTEE OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
Liability, if any, is limited to replacement of the product or refund of the purchase price. LABOR OR COST OF LABOR AND OTHER CONSEQUENTIAL DAMAGES ARE HEREBY EXCLUDED.
09900 2001.1 / PDS / 2
|