PRODUCT DATA
335
Tropicoat Masonry Primer
100% ACRYLIC 鈥? ALKALI RESISTANT 鈥? INTERIOR / EXTERIOR 鈥? 335
Vehicle Type
Product Description Waterborne 鈥? 100% Acrylic
Tropicoat Masonry Primer is a superior quality interior/exterior 100%
Finish
acrylic masonry primer. Tropicoat Masonry Primer鈥檚 unique formulation
Flat 鈥? 85掳 Sheen - 1.0 to 5.0
provides outstanding resistance to the damaging effects of highly alkaline
(high pH) surfaces and efflorescence. Tropicoat Masonry Primer is easy
Use
to apply, and provides remarkable adhesion to a variety of cement-based
Interior / Exterior
substrates and is extremely resistant to blistering, chipping, cracking and
peeling.
Percent Solids By Weight
Tropicoat Masonry Primer is designed for use on a wide variety of properly 51.4% 卤 2%
prepared interior or exterior concrete and masonry surfaces, including;
cement plaster/stucco, cement-fiber siding (i.e. James Hardie or Cemplank) Percent Solids By Volume
products, tilt-up, poured-in-place, pre-cast concrete, or just about any 37.1% 卤 2%
cement-based substrate and is also suitable for wood and drywall. Tropicoat
Suggested Coverage
Masonry Primer is designed for use on residential, commercial, institutional,
300-500 SFPG
and light industrial applications, when architectural-grade finishes are
scheduled.
Dry Film Thickness
1.5 mils @ 400 SFPG
Performance
Viscosity
鈥? Easy to apply
100 KU 卤 5
鈥? Low odor
鈥? Excellent adhesion Flash Point
鈥? Non-flammable 鈥? >200掳 F.
Good alkali resistance
鈥? Good efflorescence resistance
VOC
鈥? Soap & water cleanup
Contains .98 lbs./gal. (117 gms./ltr.)
Complies with all Federal, State and
May be applied to properly prepared... Local VOC standards.
鈥? Concrete and Masonry including: Application Equipment
鈥? Masonry Stucco 鈥? Portland Cement Plaster Brush, roller, airless or
conventional spray
鈥? Portland Cement Plaster 鈥? Poured & Precast Concrete
鈥? Cement-fiber Siding Drying Time
鈥? Wood & Drywall At 75掳F. / 50% RH
1 hour to touch
Limitations 4 hours to recoat
Allow a minimum of three (3) days of cure time for new masonry, a seven
Colors
(7) day cure time for poured in place concrete and a pH level of 13 or lower
White
prior to application of product. Coatings have a greater resistance against
failure when applied to a surface with a lower alkaline level (below 8.5).
Products Included in This Line
Not recommended for steps, walkways, or other foot or vehicle traffic
335 - White
areas. Do not use for immersion service, below grade substrates, or
substrates constantly in contact with moisture. Do not use in highly
corrosive or chemical environments, or areas subject to intense heat.
s
COLOR WHEEL PAINTS & COATINGS
Product Index 鈥? Category 3
2814 Silver Star Road 鈥? Orlando, Florida 32808
Exterior Primers, Sealers
407-293-6810 鈥? 800-749-6810 鈥? Fax 407-293-0945
www.colorwheel.com & Conditioners
09900
0335.07.3 / PDS / 1
335 TROPICOAT MASONRY PRIMER 鈥? PREMIUM 100% ACRYLIC 鈥? INTERIOR / EXTERIOR 鈥? PRIMER
Surface Preparation General Application Safety
The performance of this product is critically Mix thoroughly to a uniform consistency before WARNING! HARMFUL IF INHALED. SEE
dependent upon the soundness of the substrate each use. Apply by brush, roller or airless LABEL OR MSDS FOR LIST OF HAZARDOUS
to which it is applied. It has been determined sprayer. Work material vigorously into pores. INGREDIENTS. KEEP OUT OF REACH OF
that as high as 80% of all paint and coating Maintain a wet edge. If roller application is CHILDREN! May cause eye, skin, nose and
failures may be attributed to improper surface employed on porous surfaces, final passes throat irritation. To avoid breathing vapors
preparation. It is essential that the proper steps should be completed in a downward direction or spray mist, open windows and doors or
be taken before applying this product. to insure a uniform appearance and texture. use other means to insure fresh air entry
Apply at such a rate as to avoid runs and sags. during application and drying. If you
General:
If airless spray application is employed on experience eye watering, headaches or
Surface must be completely dry and in sound
porous surfaces, immediate 鈥渂ack rolling鈥? and dizziness, increase fresh air or wear
condition. Surface should be clean and free
鈥渂ack brushing鈥? with wet roller/brush is respiratory protection (NIOSH/MSHA TC
from dirt, grease, mill oils, form release agents,
recommended to help reduce pinholing and 23C or equivalent) or leave area. Close
rust, mill scale, chalky paint, efflorescence,
work material into pores. container after each use. Avoid contact with
organic growth, mildew, and foreign matter to
eyes and skin.
insure good adhesion of primers and/or finish Thinning:
First Aid
coats. Peeling, cracking, and chipping paint Under normal conditions thinning is not
should be removed by sandblasting, power recommended.
If you experience difficulty in breathing,
tool cleaning, hand tool cleaning, pressure Clean-Up: leave the area to obtain fresh air. If continued
washing, scraping, or wire brushing. All glossy Clean all tools and equipment with warm, difficulty is experienced, get medical
surfaces should be sanded or de-glossed. soapy water immediately after use. Flush spray assistance immediately. In case of eye
Feather sand rough edges of previously painted equipment thoroughly. contact, flush immediately with large
surfaces and spot prime bare areas. Any
amounts of fresh water for at least 15 minutes
Application Equipment
deteriorated or failed sealant and/or patching
and get medical attention; for skin, wash
compound should be removed and replaced. Brush: Use a quality nylon or polyester brush. thoroughly with soap and water. If
All unpainted substrates should be properly Roller: Use lambswool or synthetic cover: swallowed, DO NOT INDUCE VOMITING.
prepared according to respective manufacturer鈥檚 3/8" to 1 1/4" nap, depending on surface texture. Get medical attention immediately.
and/or supplier鈥檚 recommendations.
Airless Spray: Use a tip size of between 0.015" Storage and Handling
Thoroughly review and follow Color Wheel
and 0.021". Tip size should reflect equipment
鈥淪urface Preparation Guidelines鈥? and/or Color Keep from freezing or exposure to intense
type and pressure, applicator technique and
heat. Do not transfer contents to unlabeled
Wheel written specification before applying. surface conditions. Adjust pressure for constant
container.
and proper atomization.
Technical Services
Curing
Color Wheel Paints and Coatings offers and
Drying time and curing will affect the
encourages the use of our free technical
performance of the product. Do not apply
service. We also advise you to contact us
when air, surface or product temperatures are
regularly for updates to this and other
below 50掳 F. or above 100掳 F. Surface
technical data. For technical assistance, to
temperature must be at least 5掳 F. above dew
arrange a consultation with a Sales
point. Plan ahead and avoid applying when
Representative, or for current technical data,
damp or threatening weather is expected.
consult your yellow pages for the Color
Product must cure at least 8 hours before being
Wheel location nearest you, or call toll free
subjected to moisture. During extremely warm
(800) 749-6810.
weather, maintaining a wet edge may become
difficult. Avoid application during the heat of
the day. During cool weather, be aware of
possible surfactant leaching. Do not apply late
in the day where dew or condensation may
form before product begins to cure. Allow this
product to cure a minimum of 30 days before
cleaning.
All technical advice, recommendations, and services are rendered by Color Wheel gratis. They are based on technical data which Color Wheel believes to be reliable, and are intended for use by persons having skill and knowhow at their own discretion and risk.
Color Wheel Paint Manufacturing Company, Inc. assumes no responsibility for results obtained or damages incurred from their use by purchaser/user in whole or in part. All information is subject to change without notice.
NOTE: Where applicable, and for consistency, technical data and test results contained in this document are based on the pure white base of the particular product line.
LIMITATION OF LIABILITY: COLOR WHEEL MAKES NO WARRANTY OR GUARANTEE OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. UNLESS THE PRODUCT YOU PURCHASE INCLUDES A WRITTEN LIMITED WARRANTY, LIABILITY OF COLOR WHEEL,
IF ANY, IS LIMITED TO THE REPLACEMENT OF THE PRODUCT OR REFUND OF THE PURCHASE PRICE. LABOR AND COST OF LABOR AND OTHER INDIRECT, SPECIAL OR CONSEQUENTIAL DAMAGES ARE HEREBY EXCLUDED. USER IS RESPONSIBLE TO DETERMINE SUITABILITY OF PRODUCT FOR INTENDED USE.
09900 0335.07.3 / PDS / 2
|