PRODUCT DATA
3730
Weathermaster Satin House Paint
E X T E R I O R 鈥? A C RY L I C L AT E X 鈥? S AT I N 鈥? 3 7 0 0 L I N E
Vehicle Type
Product Description Waterborne 鈥? Modified Acrylic
Weathermaster Satin House Paint is a high quality exterior acrylic latex
Finish
satin paint recommended for use on a diverse number of properly primed
Satin 鈥? 60掳 Sheen - 4.0 to 8.0
and prepared surfaces. The addition of zinc oxide and organic mildewcides 85掳 Sheen - 30 to 40
Use
give Weathermaster Satin House Paint excellent protection against mildew.
Exterior
This product鈥檚 tremendous resistance to efflorescence makes it an ideal
product for use on new masonry surfaces. Years of testing and exposure
Percent Solids By Weight
in the demanding southern climates have proven that Weathermaster 51.3% 卤 2%
Satin House Paint provides outstanding performance and durability.
Percent Solids By Volume
Weathermaster Satin House Paint is designed for use in residential,
37.0% 卤 2%
architectural, commercial and light industrial applications.
Suggested Coverage
Performance 300-500 SFPG
鈥? Excellent adhesion and long term durability
Dry Film Thickness
鈥? Excellent resistance to mildew and organic growth 1.4 mils @ 400 SFPG
鈥? Very good color retention and chalk resistance
Viscosity
鈥? Excellent resistance to alkali and efflorescence
100 KU 卤 5
鈥? High resistance to blistering, cracking, chipping and peeling
鈥? Good dirt resistant, scrubbable and washable Flash Point
鈥? Easy to apply, high hiding and excellent coverage Non-flammable 鈥? >200掳 F.
VOC
May be applied to properly primed and prepared鈥?
Contains .68 lbs./gal. (81 gms./ltr.)
鈥? Concrete, Masonry and Stucco including: Complies with all Federal, State
and Local VOC standards.
Brick 鈥? Cement Plaster 鈥? Concrete Masonry Units (CMU)
鈥?
鈥? Poured and Precast Concrete 鈥? Cementitious Siding
Application Equipment
鈥? Synthetic Masonry Stucco (EIFS) Brush, roller, airless or
conventional spray
鈥? Wood 鈥? Plywood 鈥? Hardboard 鈥? Gypsum Wallboard
鈥? Ferrous Metals 鈥? Structural Steel 鈥? Aluminum Drying Time
鈥? Galvanized Metals At 75掳F. / 50% RH
1 hour to touch
4 hours to recoat
Limitations
Colors
Not recommended for steps, walkways, or other foot or vehicle traffic
White, off whites, pastels, light
areas. Do not use for immersion service, below grade substrates, or
and medium colors
substrates constantly in contact with moisture. Do not use in highly
corrosive or chemical environments, or areas subject to intense heat.
Products Included in This Line
3730 - White
3731 - Tint White
COLOR WHEEL PAINT MANUFACTURING COMPANY, INC.
Product Index 鈥? Category 1
2814 Silver Star Road 鈥? Orlando, Florida 32808
407-293-6810 鈥? 800-749-6810 鈥? Fax 407-293-0945
Exterior Paints & Coatings
www.colorwheelpaint.com
09900
2001.1 / PDS / 1
3730 LINE WEATHERMASTER SATIN HOUSE PAINT 鈥? EXTERIOR 鈥? ACRYLIC LATEX 鈥? SATIN
Surface Preparation Recommended Primers (continued) Curing
The performance of this product is critically New Plywood and Cured, Moisture-Free Drying time and curing will affect the
dependent upon the soundness of the substrate Pressure Treated Wood: Prime with 330 Optima performance of the product. Do not apply
to which it is applied. It has been determined All Prime. when air, surface or product temperatures are
that as high as 80% of all paint and coating below 50藲 F. or above 100藲 F. Surface
Previously Painted Wood: Prime with 330
failures may be attributed to improper surface temperature must be at least 5藲 F. above dew
Optima All Prime, 531 Tropicoat Quick Prime
preparation. It is essential that the proper steps point. Plan ahead and avoid applying when
or 532 Weathermaster Wood Prime. Surfaces
be taken before applying this product. damp or threatening weather is expected.
in good condition may be self primed when
Product must cure at least 8 hours before being
General: properly prepared.
subjected to moisture. During extremely warm
Surface must be completely dry and in sound New Ferrous Metal and Rusted Metal: Remove weather, maintaining a wet edge may become
condition. Surface should be clean and free all rust and mill scale then prime with 635 Line difficult. Avoid application during the heat of
from dirt, grease, mill oils, rust, mill scale, Ironize Inhibitive Primer or 1635 Line Aquatec the day. During cool weather, be aware of
chalky paint, efflorescence, organic growth, Waterborne Industrial Primer. possible surfactant leaching. Do not apply late
mildew, and foreign matter to insure good
New Galvanized Metal and Aluminum: in the day where dew or condensation may
adhesion of primers and/or finish coats.
Clean per SSPC-SP1 Solvent Cleaning or use a form before product begins to cure. Allow this
Peeling, cracking, and chipping paint
degreasing cleaner. Wipe clean with lint free product to cure a minimum of 30 days before
should be removed by sandblasting, power
cloth. All mill oils must be removed. Neutralize cleaning.
tool cleaning, hand tool cleaning, pressure
with vinegar or appropriate wash primer.
washing, scraping, or wire brushing. All Safety
Rinse thoroughly, then prime with 330 Optima
glossy surfaces should be sanded or
All Prime or 1635 Line Aquatec Waterborne WARNING! HARMFUL IF INHALED. SEE
de-glossed. Feather sand rough edges of
Industrial Primer. LABEL OR MSDS FOR LIST OF HAZARDOUS
previously painted surfaces and spot prime
INGREDIENTS. KEEP OUT OF REACH OF
Previously Painted Metals: Prime with 635
bare areas. Any deteriorated or failed sealant
CHILDREN! May cause eye, skin, nose and
Line Ironize Inhibitive Primer, 330 Optima All
and/or patching compound should be
throat irritation. To avoid breathing vapors or
Prime or 1635 Line Aquatec Waterborne
removed and replaced. All unpainted
spray mist, open windows and doors or use
Industrial Primer. Surfaces in good condition
substrates should be properly prepared
other means to insure fresh air entry during
may be self primed when properly prepared.
according to respective manufacturer鈥檚 and/or
application and drying. If you experience eye
General Application
supplier鈥檚 recommendations. Thoroughly
watering, headaches or dizziness, increase fresh
review and follow Color Wheel 鈥淪urface
Mix thoroughly to a uniform consistency before air or wear respiratory protection (NIOSH/
Preparation Guidelines鈥? and/or Color Wheel
each use. Apply by brush, roller or airless MSHA TC 23C or equivalent) or leave area.
written specification before applying.
sprayer. Work material vigorously into pores. Close container after each use. Avoid contact
Recommended Primers Maintain a wet edge. If roller application is with eyes and skin.
employed on porous surfaces, final passes
New Masonry and Stucco: Hot Stucco (three
First Aid
should be completed in a downward direction
(3) days after stucco application or with a pH
to insure a uniform appearance and texture. If you experience difficulty in breathing, leave
Range of between 8-12) use 1252 Quick Cure
Apply at such a rate as to avoid runs and sags. the area to obtain fresh air. If continued difficulty
Acrylic Conditioner. Prime alkaline masonry
If airless spray application is employed on is experienced, get medical assistance
(pH Range: 8-10) with 330 Optima All Prime,
porous surfaces, immediate 鈥渂ack rolling鈥? and immediately. In case of eye contact, flush
335 Tropicoat Masonry Primer or 952 Fas-Gard
鈥渂ack brushing鈥? with wet roller/brush is immediately with large amounts of fresh water
Conditioner. Prime non-alkaline masonry with
recommended to help reduce pinholing and for at least 15 minutes and get medical attention;
330 Optima All Prime, 335 Tropicoat Masonry
work material into pores. for skin, wash thoroughly with soap and water.
Primer or self prime. Prime porous masonry
If swallowed, DO NOT INDUCE VOMITING.
with 250 Ti-Gard Masonry Filler or 3250 Thinning:
Get medical attention immediately.
Hi-Build Block Filler. Under normal conditions thinning is not
recommended.
Previously Painted Masonry and Stucco: Prime Storage and Handling
chalky surfaces with 950 Ti-Gard Conditioner, Clean-Up: Keep from freezing or exposure to intense heat.
1250 Ti-Gard Latex Conditioner or 1252 Quick Clean all tools and equipment with warm, Do not transfer contents to unlabeled container.
Cure Acrylic Conditioner. Surfaces in good soapy water immediately after use. Flush spray
condition may be self primed when properly Technical Services
equipment thoroughly.
prepared.
Application Equipment Color Wheel Paints and Coatings offers and
Synthetic Masonry Stucco (EIFS): Prime with encourages the use of our free technical
Brush: Use a quality nylon or polyester brush.
330 Optima All Prime, 1250 Ti-Gard Latex service. We also advise you to contact us
Conditioner or 1252 Quick Cure Acrylic Roller: Use lambswool or synthetic cover: regularly for updates to this and other
Conditioner. Surfaces in good condition may 3/8" to 1 1/4" nap, depending on surface texture. technical data. For technical assistance, to
be self primed when properly prepared. arrange a consultation with a Sales
Airless Spray: Use a tip size of between 0.015"
New Wood and Hardboard: Can be self-primed, Representative, or for current technical data,
and 0.021". Tip size should reflect equipment
but recommend priming with 330 Optima All consult your yellow pages for the Color
type and pressure, applicator technique and
Prime, 531 Tropicoat Quick Prime or 532 Wheel location nearest you, or call toll free
surface conditions. Adjust pressure for constant
Weathermaster Wood Prime. Bleeding woods (800) 749-6810.
and proper atomization.
may require two coats of primer.
All technical advice, recommendations, and services are rendered by Color Wheel gratis. They are based on technical data which Color Wheel believes to be reliable, and are intended for use by persons having skill and knowhow at their own discretion and risk.
Color Wheel Paint Manufacturing Company, Inc. assumes no responsibility for results obtained or damages incurred from their use by purchaser/user in whole or in part. All information is subject to change without notice.
NOTE: Where applicable, and for consistency, technical data and test results contained in this document are based on the pure white base of the particular product line.
LIMITATION OF LIABILITY: COLOR WHEEL MAKES NO WARRANTY OR GUARANTEE OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
Liability, if any, is limited to replacement of the product or refund of the purchase price. LABOR OR COST OF LABOR AND OTHER CONSEQUENTIAL DAMAGES ARE HEREBY EXCLUDED.
09900 2001.1 / PDS / 2
|