PRODUCT DATA
330
Optima All Prime
PREMIUM 100% ACRYLIC PRIMER 鈥? INTERIOR / EXTERIOR 鈥? 330
Vehicle Type
Product Description Waterborne 鈥? 100% Acrylic
Optima All Prime is a superior quality interior / exterior 100% acrylic latex
multipurpose primer designed for use in residential, architectural, Finish
commercial and light industrial applications on a diverse number of Flat 鈥? 85掳 Sheen - 1.0 to 10.0
properly prepared substrates. The addition of zinc oxide and organic
Use
mildewcides give Optima All Prime excellent protection against mildew.
Interior / Exterior
Optima All Prime's 100% acrylic resin formulation provides the ultimate
performance and durability.
Percent Solids By Weight
50.0% 卤 2%
Performance
鈥? Easy to apply and low odor Percent Solids By Volume
鈥? Excellent adhesion and resistant to moisture 37.0% 卤 2%
鈥? Excellent alkali and efflorescence resistance
鈥? Remarkable resistance to blistering, cracking, chipping and peeling Suggested Coverage
300-400 SFPG
鈥? Outstanding resistance to mildew and organic growth
鈥? Outstanding stain blocking properties
Dry Film Thickness
鈥? Good enamel holdout 1.6 mils @ 370 SFPG
鈥? Non-yellowing formulation
Viscosity
May be applied to properly prepared... 85 KU 卤 5
鈥? Concrete, Masonry and Stucco including:
Flash Point
Brick , Cement Plaster, Poured and Precast Concrete
Non-flammable 鈥? >200掳 F.
鈥? Wood Surfaces including: Wood Trim, Lumber, Pressure Treated,
Plywood, Wood Fascia, Wood Soffit and Wood Siding VOC
鈥? Contains .83 lbs./gal. (99 gms./ltr.)
Hardboard Siding and Cementitious Siding
Complies with all Federal, State and
鈥? Synthetic Masonry Stucco (EIFS)
Local VOC standards.
鈥? Aluminum, Galvanized Metals, Copper and Stainless Steel
鈥? Gypsum Wallboard and Gypsum and Veneer Plaster Application Equipment
鈥? Acoustical Ceilings and Fiberglass Brush, roller, airless or
conventional spray
Specification Standards Drying Time
鈥? Performance alternate for Federal Specification: At 75掳F. / 50% RH
1 hour to touch
TT-P-1984; MIL-S-12935D
4 hours to recoat
Limitations Colors
Not for use as a rust primer. Finish coats should be apllied within ten days White
or recleaning and re-priming will be needed. Allow a minimum of three (3)
days of cure time for new masonry, a seven (7) day cure time for poured in Products Included in This Line
place concrete and a pH level of 13 or lower prior to application of product. 330 - White
Coatings have a greater resistance against failure when applied to a surface
with a lower alkaline level (below 8.5). Can be used on wood floor surfaces
as a primer only. Do not use for immersion service, below grade substrates,
or substrates constantly in contact with moisture. Do not use in highly
corrosive or chemical environments, or areas subject to intense heat.
COLOR WHEEL PAINTS & COATINGS
Product Index 鈥? Category 3
2814 Silver Star Road 鈥? Orlando, Florida 32808
Exterior Primers, Sealers
407-293-6810 鈥? 800-749-6810 鈥? Fax 407-293-0945
www.colorwheel.com & Conditioners
09900
0330.07.3 / PDS / 1
330 OPTIMA ALL PRIME 鈥? PREMIUM 100% ACRYLIC 鈥? INTERIOR / EXTERIOR 鈥? PRIMER
Surface Preparation General Application Safety
The performance of this product is critically Mix thoroughly to a uniform consistency before WARNING! HARMFUL IF INHALED. SEE
dependent upon the soundness of the substrate each use. Apply by brush, roller or airless LABEL OR MSDS FOR LIST OF HAZARDOUS
to which it is applied. It has been determined sprayer. Work material vigorously into pores. INGREDIENTS. KEEP OUT OF REACH OF
that as high as 80% of all paint and coating Maintain a wet edge. If roller application is CHILDREN! May cause eye, skin, nose and
failures may be attributed to improper surface employed on porous surfaces, final passes throat irritation. To avoid breathing vapors
preparation. It is essential that the proper steps should be completed in a downward direction or spray mist, open windows and doors or
be taken before applying this product. to insure a uniform appearance and texture. use other means to insure fresh air entry
Apply at such a rate as to avoid runs and sags. during application and drying. If you
General:
If airless spray application is employed on experience eye watering, headaches or
Surface must be completely dry and in sound
porous surfaces, immediate 鈥渂ack rolling鈥? and dizziness, increase fresh air or wear
condition. Surface should be clean and free
鈥渂ack brushing鈥? with wet roller/brush is respiratory protection (NIOSH/MSHA TC
from dirt, grease, mill oils, form release agents,
recommended to help reduce pinholing and 23C or equivalent) or leave area. Close
rust, mill scale, chalky paint, efflorescence,
work material into pores. container after each use. Avoid contact with
organic growth, mildew, and foreign matter to
eyes and skin.
insure good adhesion of primers and/or finish Thinning:
First Aid
coats. Peeling, cracking, and chipping paint Under normal conditions thinning is not
should be removed by sandblasting, power recommended.
If you experience difficulty in breathing,
tool cleaning, hand tool cleaning, pressure Clean-Up: leave the area to obtain fresh air. If continued
washing, scraping, or wire brushing. All glossy Clean all tools and equipment with warm, difficulty is experienced, get medical
surfaces should be sanded or de-glossed. soapy water immediately after use. Flush spray assistance immediately. In case of eye
Feather sand rough edges of previously painted equipment thoroughly. contact, flush immediately with large
surfaces and spot prime bare areas. Any
amounts of fresh water for at least 15 minutes
Application Equipment
deteriorated or failed sealant and/or patching
and get medical attention; for skin, wash
compound should be removed and replaced. Brush: Use a quality nylon or polyester brush. thoroughly with soap and water. If
All unpainted substrates should be properly Roller: Use lambswool or synthetic cover: swallowed, DO NOT INDUCE VOMITING.
prepared according to respective manufacturer鈥檚 3/8" to 1 1/4" nap, depending on surface texture. Get medical attention immediately.
and/or supplier鈥檚 recommendations.
Airless Spray: Use a tip size of between 0.015" Storage and Handling
Thoroughly review and follow Color Wheel
and 0.021". Tip size should reflect equipment
鈥淪urface Preparation Guidelines鈥? and/or Color Keep from freezing or exposure to intense
type and pressure, applicator technique and
heat. Do not transfer contents to unlabeled
Wheel written specification before applying. surface conditions. Adjust pressure for constant
container.
and proper atomization.
Technical Services
Curing
Color Wheel Paints & Coatings offers and
Drying time and curing will affect the
encourages the use of our free technical
performance of the product. Do not apply
service. We also advise you to contact us
when air, surface or product temperatures are
regularly for updates to this and other
below 50掳 F. or above 100掳 F. Surface
technical data. For technical assistance, to
temperature must be at least 5掳 F. above dew
arrange a consultation with a Sales
point. Plan ahead and avoid applying when
Representative, or for current technical data,
damp or threatening weather is expected.
consult your yellow pages for the Color
Product must cure at least 8 hours before being
Wheel location nearest you, or call toll free
subjected to moisture. During extremely warm
(800) 749-6810.
weather, maintaining a wet edge may become
difficult. Avoid application during the heat of
the day. During cool weather, be aware of
possible surfactant leaching. Do not apply late
in the day where dew or condensation may
form before product begins to cure. Allow this
product to cure a minimum of 30 days before
cleaning.
All technical advice, recommendations, and services are rendered by Color Wheel gratis. They are based on technical data which Color Wheel believes to be reliable, and are intended for use by persons having skill and knowhow at their own discretion and risk.
Color Wheel assumes no responsibility for results obtained or damages incurred from their use by purchaser/user in whole or in part. All information is subject to change without notice.
NOTE: Where applicable, and for consistency, technical data and test results contained in this document are based on the pure white base of the particular product line.
LIMITATION OF LIABILITY: COLOR WHEEL MAKES NO WARRANTY OR GUARANTEE OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. UNLESS THE PRODUCT YOU PURCHASE INCLUDES A WRITTEN LIMITED WARRANTY, LIABILITY OF COLOR WHEEL,
IF ANY, IS LIMITED TO THE REPLACEMENT OF THE PRODUCT OR REFUND OF THE PURCHASE PRICE. LABOR AND COST OF LABOR AND OTHER INDIRECT, SPECIAL OR CONSEQUENTIAL DAMAGES ARE HEREBY EXCLUDED. USER IS RESPONSIBLE TO DETERMINE SUITABILITY OF PRODUCT FOR INTENDED USE.
09900 0330.07.3 / PDS / 2
|