PRODUCT DATA
200
Hi-Hide Interior/Exterior Wall Paint
CONTRACTOR鈥橲 CHOICE 鈥? EXTRA FLAT 鈥? 200 LINE
Vehicle Type
Product Description Waterborne 鈥? Latex
Hi-Hide Interior / Exterior Wall Paint is a high quality latex flat paint
Finish
designed for use in residential, architectural and commercial applications
Flat 鈥? 85掳 Sheen - 1.0 to 5.0
on a variety of properly primed and prepared masonry surfaces, cement
Use
plaster and gypsum wallboard.
Interior / Exterior
Performance
Percent Solids By Weight
鈥? 52.8% 卤 2%
Outstanding touch up properties
鈥? High hiding
Percent Solids By Volume
鈥? Very good adhesion
34.2% 卤 2%
鈥? Easy to apply
鈥? Scrubbable and washable Suggested Coverage
300-500 SFPG
Dry Film Thickness
May be applied to properly primed and prepared...
1.4 mils @ 400 SFPG
鈥? Interior and Exterior Concrete, Masonry and Stucco including:
Viscosity
Concrete Masonry Units (CMU)
鈥?
100 KU 卤 5
鈥? Poured and Precast Concrete
Flash Point
鈥? Interior Wood Non-flammable 鈥? >200掳 F.
鈥? Interior Gypsum Wallboard
VOC
Contains .95 lbs./gal. (114 gms./ltr.)
Specification Standards Complies with all Federal, State
and Local VOC standards.
鈥? Performance alternate for Federal Specification:
TT-P-29J Application Equipment
Brush, roller, airless or
conventional spray
Limitations
Recommended primers must be used prior to applying finish coats. Drying Time
At 75掳F. / 50% RH
Masonry surfaces must be at a safe level of pH (below 8.5), unless
1 hour to touch
recommended primers are used, prior to painting. Not recommended for 4 hours to recoat
steps, walkways, or other foot or vehicle traffic areas. Do not use on below
Colors
grade substrates, or substrates constantly in contact with moisture. Do not
White, off whites, pastels, light
use in corrosive or chemical environments, or areas subject to intense
and medium colors
heat.
Products Included in This Line
200 - White
201 - Tint White
202 - Deep Tint Base
COLOR WHEEL PAINT MANUFACTURING COMPANY, INC.
Product Index 鈥? Category 1 & 4
2814 Silver Star Road 鈥? Orlando, Florida 32808
407-293-6810 鈥? 800-749-6810 鈥? Fax 407-293-0945
Interior / Exterior Paints
www.colorwheelpaint.com
09900
2001.1 / PDS / 1
200 LINE CONTRACTOR鈥橲 CHOICE 鈥? HI-HIDE INTERIOR/EXTERIOR WALL PAINT 鈥? FLAT
Surface Preparation Recommended Primers - Interior (continued) Curing
The performance of this product is critically Interior - New Wood and Plywood: Prime with Drying time and curing will affect the
dependent upon the soundness of the substrate 830 Gloss Prep Undercoat, 831 Gloss Prep Fast performance of the product. Do not apply
to which it is applied. It has been determined Dry Undercoat or 8300 Gloss Prep Waterborne when air, surface or product temperatures are
that as high as 80% of all paint and coating Undercoat. Bleeding woods may require two below 50藲 F. or above 100藲 F. Surface
failures may be attributed to improper surface coats of primer. temperature must be at least 5藲 F. above dew
preparation. It is essential that the proper steps point. Plan ahead and avoid applying when
Interior - Previously Painted Wood: Prime
be taken before applying this product. damp or threatening weather is expected.
with 830 Gloss Prep Undercoat, 831 Gloss
Product must cure at least 8 hours before being
General: Prep Fast Dry Undercoat or 8300 Gloss Prep
subjected to moisture. During extremely warm
Waterborne Undercoat. Surfaces in good
Surface must be completely dry and in sound
weather, maintaining a wet edge may become
condition may be self primed when properly
condition. Surface should be clean and free
difficult. Avoid application during the heat of
prepared.
from dirt, grease, mill oils, rust, mill scale,
the day. During cool weather, be aware of
Recommended Primers - Exterior
chalky paint, efflorescence, organic growth,
possible surfactant leaching. Do not apply late
mildew, and foreign matter to insure good Exterior - New Masonry and Stucco: Hot Stucco
in the day where dew or condensation may
adhesion of primers and/or finish coats. (three (3) days after application) use 1252 Quick
form before product begins to cure. Allow this
Peeling, cracking, and chipping paint Cure Acrylic Conditioner. Prime alkaline
product to cure a minimum of 30 days before
should be removed by sandblasting, power masonry (pH Range: 8-10) with 330 Optima All
cleaning.
tool cleaning, hand tool cleaning, pressure Prime, 335 Tropicoat Masonry Primer or 952
Safety
washing, scraping, or wire brushing. All Fas-Gard Conditioner. Prime non-alkaline
glossy surfaces should be sanded or WARNING! HARMFUL IF INHALED. SEE
masonry with 330 Optima All Prime, 335
de-glossed. Feather sand rough edges of LABEL OR MSDS FOR LIST OF HAZARDOUS
Tropicoat Masonry Primer or self-prime. Prime
previously painted surfaces and spot prime INGREDIENTS. KEEP OUT OF REACH OF
porous masonry with 250 Ti-Gard Masonry
bare areas. Any deteriorated or failed sealant CHILDREN! May cause eye, skin, nose and
Filler or 3250 Hi-Build Block Filler.
and/or patching compound should be throat irritation. To avoid breathing vapors or
Exterior - Previously Painted Masonry and
removed and replaced. All unpainted spray mist, open windows and doors or use
Stucco: Prime chalky surfaces with 950
substrates should be properly prepared other means to insure fresh air entry during
Ti-Gard Conditioner, 1250 Ti-Gard Latex
according to respective manufacturer鈥檚 and/or application and drying. If you experience eye
Conditioner or 1252 Quick Cure Acrylic
supplier鈥檚 recommendations. Thoroughly watering, headaches or dizziness, increase fresh
Conditioner. Surfaces in good condition may
review and follow Color Wheel 鈥淪urface air or wear respiratory protection (NIOSH/
be self primed when properly prepared.
Preparation Guidelines鈥? and/or Color Wheel MSHA TC 23C or equivalent) or leave area.
General Application
written specification before applying. Close container after each use. Avoid contact
Mix thoroughly to a uniform consistency before
Recommended Primers - Interior with eyes and skin.
each use. Apply by brush, roller or airless
First Aid
Interior - New Plaster and Gypsum Wallboard: sprayer. Work material vigorously into pores.
Allow plaster to cure and be sure all drywall If you experience difficulty in breathing, leave
Maintain a wet edge. If roller application is
joint compound is thoroughly dry and cured. the area to obtain fresh air. If continued difficulty
employed on porous surfaces, final passes
Prime with 430 Ti-Gard Interior Sealer, 330 is experienced, get medical assistance
should be completed in a downward direction
Optima All Prime, 830 Gloss Prep Undercoat, immediately. In case of eye contact, flush
to insure a uniform appearance and texture.
831 Gloss Prep Fast Dry Undercoat, 8300 immediately with large amounts of fresh water
Apply at such a rate as to avoid runs and sags.
Gloss Prep Waterborne Undercoat or self primed for at least 15 minutes and get medical attention;
If airless spray application is employed on
when properly prepared. for skin, wash thoroughly with soap and water.
porous surfaces, immediate 鈥渂ack rolling鈥? and
Interior - Previously Painted Plaster and If swallowed, DO NOT INDUCE VOMITING.
鈥渂ack brushing鈥? with wet roller/brush is
Wallboard: Prime with 430 Ti-Gard Interior Get medical attention immediately.
recommended to help reduce pinholing and
Sealer, 330 Optima All Prime, 830 Gloss Prep
Storage and Handling
work material into pores.
Undercoat, 831 Gloss Prep Fast Dry Undercoat Thinning: Keep from freezing or exposure to intense heat.
or 8300 Gloss Prep Waterborne Undercoat. Under normal conditions thinning is not Do not transfer contents to unlabeled container.
Surfaces in good condition may be self primed recommended. Technical Services
when properly prepared. Clean-Up:
Color Wheel Paints and Coatings offers and
Interior - New Concrete and Masonry : Prime Clean all tools and equipment with warm,
encourages the use of our free technical
alkaline masonry (pH Range: 8-10) with 330 soapy water immediately after use. Flush spray
service. We also advise you to contact us
Optima All Prime, 952 Fas-Gard Conditioner equipment thoroughly.
regularly for updates to this and other
or 1252 Quick Cure Acrylic Conditioner. Prime
Application Equipment technical data. For technical assistance, to
non-alkaline masonry with 430 Ti-Gard Interior
Brush: Use a quality nylon or polyester brush. arrange a consultation with a Sales
Sealer, 330 Optima All-Prime, 8300 Gloss Prep
Roller: Use lambswool or synthetic cover: 3/8" Representative, or for current technical data,
Waterborne Undercoat or self prime. Prime
to 1 1/4" nap, depending on surface texture. consult your yellow pages for the Color
porous masonry with 250 Ti-Gard Masonry
Airless Spray: Use a tip size of between 0.015" Wheel location nearest you, or call toll free
Filler or 3250 Hi-Build Block Filler.
and 0.021". Tip size should reflect equipment (800) 749-6810.
Interior - Previously Painted Masonry: Prime
type and pressure, applicator technique and
with 430 Ti-Gard Interior Sealer, 330 Optima
surface conditions. Adjust pressure for constant
All Prime, or 8300 Gloss Prep Waterborne
and proper atomization.
Undercoat. Surfaces in good condition may be
self primed when properly prepared.
All technical advice, recommendations, and services are rendered by Color Wheel gratis. They are based on technical data which Color Wheel believes to be reliable, and are intended for use by persons having skill and knowhow at their own discretion and risk.
Color Wheel Paint Manufacturing Company, Inc. assumes no responsibility for results obtained or damages incurred from their use by purchaser/user in whole or in part. All information is subject to change without notice.
NOTE: Where applicable, and for consistency, technical data and test results contained in this document are based on the pure white base of the particular product line.
LIMITATION OF LIABILITY: COLOR WHEEL MAKES NO WARRANTY OR GUARANTEE OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
Liability, if any, is limited to replacement of the product or refund of the purchase price. LABOR OR COST OF LABOR AND OTHER CONSEQUENTIAL DAMAGES ARE HEREBY EXCLUDED.
09900 2001.1 / PDS / 2
|