PRODUCT DATA
280
Pro-Logix Interior Latex Wall Paint
VINYL ACRYLIC 鈥? INTERIOR 鈥? EXTRA FLAT 鈥? 280 LINE
Vehicle Type
Product Description Waterborne 鈥? Vinyl Acrylic
Pro-Logix Interior Latex Extra Flat Wall Paint is a top quality vinyl acrylic
Finish
paint with special pigments to give it an extremely flat finish for the
Flat 鈥? 85掳 Sheen - 1.0 to 5.0
purpose of reducing light reflectance to conceal wall imperfections.
Use
Pro-Logix Interior Latex Extra Flat Wall Paint provides the applicator
Interior
with excellent touch-up qualities not found in most latex wall paints. The
exceptionally durable, washable finish provided by Pro-Logix Interior
Percent Solids By Weight
Latex Extra Flat Wall Paint makes it ideal for use on interior drywall, 46.2% 卤 2%
plaster, and masonry surfaces in residential, architectural and commercial
Percent Solids By Volume
applications.
28.5% 卤 2%
Suggested Coverage
Performance 200-400 SFPG
鈥? High hiding formulation Dry Film Thickness
鈥? Extremely flat finish 1.4 mils @ 325 SFPG
鈥? Helps conceal wall imperfections
Viscosity
鈥? Excellent touch-up
114 KU 卤 5
鈥? Low odor
鈥? Soap & water cleanup Flash Point
Non-flammable 鈥? >200掳 F.
VOC
May be applied to properly primed and prepared...
Contains 1.2 lbs./gal. (105 gms./ltr.)
Complies with all Federal, State
鈥? Concrete and Masonry Surfaces including:
and Local VOC standards.
Cement Plaster
鈥?
Application Equipment
Concrete Masonry Units (CMU)
鈥?
Brush, roller, airless or
鈥? Poured and Precast Concrete (CMU)
conventional spray
鈥? Gypsum Wallboard
鈥? Gypsum Plaster and Veneer Plaster Drying Time
At 75掳F. / 50% RH
1 hour to touch
4 hours to recoat
Limitations
Colors
For interior use only. Not recommended for steps, walkways, or other foot
Ready mix colors, white, off
or vehicle traffic areas. Do not use for immersion service, below grade whites and pastel colors
substrates, or substrates constantly in contact with moisture. Do not use in
Products Included In This Line
extremely corrosive or chemical environments, or areas subject to intense
280 - Brite White
heat. And Factory Colors
COLOR WHEEL PAINT MANUFACTURING COMPANY, INC.
Product Index 鈥? Category 4
2814 Silver Star Road 鈥? Orlando, Florida 32808
407-293-6810 鈥? 800-749-6810 鈥? Fax 407-293-0945
Interior Paints & Coatings
www.colorwheel.com
09900
2006.1.1 / PDS / 1
280 LINE INTERIOR FLAT WALL PAINT 鈥? VINYL ACRYLIC 鈥? INTERIOR 鈥? EXTRA FLAT
Surface Preparation Recommended Primers (continued) Curing
The performance of this product is critically Previously Painted Masonry: Prime with 430 Drying time and curing will affect the
dependent upon the soundness of the substrate Ti-Gard Interior Sealer, 470 Equalizer HB Wall performance of the product. Do not apply
to which it is applied. It has been determined Primer/Surfacer, 330 Optima All Prime, or when air, surface or product temperatures are
that as high as 80% of all paint and coating 8300 Gloss Prep Waterborne Undercoat. below 50掳F. or above 100掳F. Surface
failures may be attributed to improper surface Surfaces in good condition may be self primed. temperature must be at least 5掳F. above dew
preparation. It is essential that the proper steps New Wood and Plywood: Prime with 831 point. Plan ahead and avoid applying when
be taken before applying this product. Gloss Prep Fast Dry Undercoat or 8300 Gloss damp or threatening weather is expected.
General: Prep Waterborne Undercoat. Bleeding woods Product must cure at least 8 hours before being
Surface must be completely dry and in may require two coats of primer. subjected to moisture. During extremely warm
sound condition. Surface should be clean weather, maintaining a wet edge may become
Previously Painted Wood: Prime with 831
and free from dirt, grease, mill oils, rust, difficult. Avoid application during the heat of
Gloss Prep Fast Dry Undercoat or 8300 Gloss
mill scale, chalky paint, efflorescence, the day. During cool weather, be aware of
Prep Waterborne Undercoat. Surfaces in good
organic growth, mildew, and foreign matter possible surfactant leaching. Do not apply late
condition may be self primed.
to insure good adhesion of primers and/or in the day where dew or condensation may
New Ferrous Metal and Rusted Metal: Remove
finish coats. Peeling, cracking, and form before product begins to cure. Allow this
all rust and mill scale then prime with 635 Line
chipping paint should be removed by product to cure a minimum of 30 days before
Ironize Inhibitive Primer or 1635 Line Aquatec
sandblasting, power tool cleaning, hand cleaning.
Waterborne Industrial Primer.
tool cleaning, pressure washing, scraping,
Safety
New Galvanized Metal and Aluminum:
or wire brushing. All glossy surfaces should
Remove all mill oils with a non-petroleum WARNING! HARMFUL IF INHALED. SEE
be sanded or de-glossed. Feather sand rough
based solvent then prime with 330 LABEL OR MSDS FOR LIST OF HAZARDOUS
edges of previously painted surfaces and
Optima All Prime or 1635 Line INGREDIENTS. KEEP OUT OF REACH OF
spot prime bare areas. Any deteriorated or
Aquatec Waterborne Industrial Primer. CHILDREN! May cause eye, skin, nose and
failed sealant and/or patching compound
Previously Painted Metals: Prime with 635 throat irritation. To avoid breathing vapors or
should be removed and replaced. All
Line Ironize Inhibitive Primer, 330 Optima All spray mist, open windows and doors or use
unpainted substrates should be properly
Prime or 1635 Line Aquatec Waterborne other means to insure fresh air entry during
prepared according to respective
Industrial Primer. Surfaces in good condition application and drying. If you experience eye
manufacturer鈥檚 and/or supplier鈥檚
may be self primed. watering, headaches or dizziness, increase fresh
recommendations. Thoroughly review and
air or wear respiratory protection (NIOSH/
follow Color Wheel 鈥淪urface Preparation General Application
MSHA TC 23C or equivalent) or leave area.
Guidelines鈥? and/or Color Wheel written
Mix thoroughly to a uniform consistency before Close container after each use. Avoid contact
specification before applying.
each use. Apply by brush, roller or airless with eyes and skin.
Recommended Primers sprayer. Work material vigorously into pores.
First Aid
New Textured Surfaces: Adding Color Wheel Maintain a wet edge. If roller application is
460 Ti-Gard Dry Wall Texture Hardener to employed on porous surfaces, final passes If you experience difficulty in breathing, leave
spray wall texture (orange peel) prior to paint should be completed in a downward direction the area to obtain fresh air. If continued difficulty
application will greatly improve the washability to insure a uniform appearance and texture. is experienced, get medical assistance
of the finish coat If texture has already been Apply at such a rate as to avoid runs and sags. immediately. In case of eye contact, flush
applied without Texture Hardener, use priming If airless spray application is employed on immediately with large amounts of fresh water
instructions below. porous surfaces, immediate 鈥渂ack rolling鈥? and for at least 15 minutes and get medical attention;
鈥渂ack brushing鈥? with wet roller/brush is
New Interior Plaster and Gypsum Wallboard: for skin, wash thoroughly with soap and water.
recommended to help reduce pinholing and
Allow plaster to cure and be sure all drywall If swallowed, DO NOT INDUCE VOMITING.
work material into pores.
joint compound is thoroughly dry and cured. Get medical attention immediately.
Prime with 430 Ti-Gard Interior Sealer, 470 Thinning: Storage and Handling
Equalizer HB Wall Primer/Surfacer, 330 Optima Under normal conditions thinning is not
Keep from freezing or exposure to intense heat.
All Prime, 831 Gloss Prep Fast Dry Undercoat, recommended.
Do not transfer contents to unlabeled container.
8300 Gloss Prep Waterborne Undercoat or self
Clean-Up:
prime.
Technical Services
Clean all tools and equipment with warm,
Previously Painted Plaster and Wallboard: soapy water immediately after use. Flush spray Color Wheel Paints and Coatings offers and
Prime with 430 Ti-Gard Interior Sealer, 470 equipment thoroughly. encourages the use of our free technical
Equalizer HB Wall Primer/Surfacer, 330 Optima
Application Equipment service. We also advise you to contact us
All Prime, 831 Gloss Prep Fast Dry Undercoat
regularly for updates to this and other
or 8300 Gloss Prep Waterborne Undercoat. Brush: Use a quality nylon or polyester brush.
technical data. For technical assistance, to
Surfaces in good condition may be self primed. Roller: Use lambswool or synthetic cover: arrange a consultation with a Sales
New Concrete and Masonry : Prime alkaline 3/8" to 1 1/4" nap, depending on surface texture. Representative, or for current technical data,
masonry (pH Range: 8-10) with 1252 Quick consult your yellow pages for the Color
Airless Spray: Use a tip size of between 0.015"
Cure Acrylic Conditioner or 330 Optima All Wheel location nearest you, or call toll free
and 0.021". Tip size should reflect equipment
Prime. Prime non-alkaline masonry with 430 (800) 749-6810.
type and pressure, applicator technique and
Ti-Gard Interior Sealer, 470 Equalizer HB Wall surface conditions. Adjust pressure for constant
Primer/Surfacer, 330 Optima All Prime, 8300 and proper atomization.
Gloss Prep Waterborne Undercoat or self prime.
Prime porous masonry with 250 Ti-Gard
Masonry Filler or 3250 Hi-Build Block Filler.
All technical advice, recommendations, and services are rendered by Color Wheel gratis. They are based on technical data which Color Wheel believes to be reliable, and are intended for use by persons having skill and knowhow at their own discretion and risk.
Color Wheel Paint Manufacturing Company, Inc. assumes no responsibility for results obtained or damages incurred from their use by purchaser/user in whole or in part. All information is subject to change without notice.
NOTE: Where applicable, and for consistency, technical data and test results contained in this document are based on the pure white base of the particular product line.
LIMITATION OF LIABILITY: COLOR WHEEL MAKES NO WARRANTY OR GUARANTEE OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
Liability, if any, is limited to replacement of the product or refund of the purchase price. LABOR OR COST OF LABOR AND OTHER CONSEQUENTIAL DAMAGES ARE HEREBY EXCLUDED.
09900 2006.1.1 / PDS / 2
|