MTL Drilling Detergent
Page 1 of 3
MATERIAL SAFETY DATA SHEET
SECTION I: IDENTIFICATION OF PRODUCT
PRODUCT NAME: MTL Drilling Detergent
PRODUCT USE: Oil Well Fluid Additive CAS NO. Proprietary
CHEMICAL FAMILY: Blend
WORK PLACE HAZARDOUS MATERIALS INFORMATION SYSTEM (WHMIS)
WHMIS CLASSIFICATION: D2A; D2B
WORK PLACE HAZARD: Toxic effects; skin and eye irritant; Flammable
TRANSPORTATION OF DANGEROUS GOODS (TDG)
SHIPPING NAME: Flammable Liquid, Toxic, N.O.S ( Methanol)
TDG CLASSIFICATION: 3, 6.1
UN NUMBER (PIN): 1992
PACKING GROUP: II
SECTION II: HAZARDOUS INGREDIENTS
INGREDIENT PERCENT CAS NUMBER LD RAT OSHA PEL ACGIH TLV
(50)
Methanol <20% 67-56-1 N/A 200ppm
SECTION III: TOXICOLOGICAL PROPERTIES
ROUTE OF ENTRY: [XX] SKIN [XX] EYE CONTACT [XX] INHALATION [XX] INGESTION
鈥?
EMERGENCY OVERVIEW: May cause irritation or drying of the skin
鈥? Inhalation of any chemical may be harmful
鈥? Vapour or spray mist harmful
鈥? Ingestion may cause blindness.
EYE CONTACT: Liquid or mist causes irritation.
SKIN CONTACT: May cause irritation or drying of the skin.
INGESTION: Harmful if swallowed. May cause nausea, vomiting, dizziness, drowsiness, blurred vision,
and nervous system effects. May cause burns to mucous membranes. Ingestion of
methanol may cause blindness.
MTL Drilling Detergent
Page 2 of 3
MATERIAL SAFETY DATA SHEET
INHALATION: May cause irritation of the nose and throat with headache. Breathing high concentrations
may cause nausea, vomiting, headache, dizziness, and irregular eye movements.
SECTION IV: FIRST AID MEASURES
SKIN CONTACT: Immediately wash skin with soap and plenty of water for at least 15 minutes and get medical
attention if symptoms persist.
EYE CONTACT: Flush immediately with plenty of water for at least 15 minutes and get medical attention if
symptoms persist.
INGESTION: If swallowed, give two glasses of water to drink. Consult a physician. Never give anything by
mouth to an unconscious person.
INHALATION: Remove to fresh air.
SECTION V: PHYSICAL DATA
APPEARANCE AND ODOUR: Amber liquid, mild odour
SPECIFIC GRAVITY(@ 20掳C): .958
BOILING POINT (掳 C): N/D
FREEZING POINT (掳C): -25 0 C
SOLUBILITY IN WATER: Soluble
PERCENT VOLATILE BY VOLUME: N/D
EVAPORATION RATE: N/A
SECTION VI: FIRE AND EXPLOSION HAZARD DATA
FLASH POINT: Above 62 0 C (145 0 F)
FLAMMABLE LIMITS: N/D
EXTINGUISHING MEDIA: Carbon Dioxide, or Alcohol foam, Dry Powder
SPECIAL FIRE FIGHTING PROCEDURES: N/A
UNUSUAL FIRE AND EXPLOSION HAZARDS: Splattering of material.
SECTION VII: REACTIVITY DATA
STABILITY: Stable [XX] Unstable [ ]
INCOMPATIBILITY (CONDITIONS TO AVOID): None Known
MTL Drilling Detergent
Page 3 of 3
MATERIAL SAFETY DATA SHEET
CONDITIONS OF REACTIVITY: None Known
HAZARDOUS DECOMPOSITION PRODUCTS: None
HAZARDOUS POLYMERIZATION: Will Not Occur [XX] May Occur [ ]
SECTION VIII: PREVENTIVE MEASURES
SPECIAL PROTECTION INFORMATION
RESPIRATORY PROTECTION: Not normally required.
VENTILATION: Local exhaust
PROTECTIVE GLOVES: Wear impervious gloves.
EYE PROTECTION: Use goggles or face shield if splashing is likely.
OTHER PROTECTIVE EQUIPMENT (Specify): Not normally required.
PRECAUTIONS TO BE TAKEN IN HANDLING AND STORING
Wear impervious gloves. Use goggles or face shield if splashing is likely. Chemical type apron recommended. Keep
away from heat and flame. Use with adequate ventilation. Avoid prolonged or repeated contact with skin. Do not get in
eyes, on skin, or on clothing. Wash thoroughly after handling. Launder contaminated clothing before reuse.
STEPS TO BE TAKEN IN CASE THE MATERIAL IS SPILLED OR RELEASED
In case of spillage, absorb with inert material and dispose of in accordance with applicable regulations.
WASTE DISPOSAL METHOD
Follow Federal and State regulations.
SECTION IX: PREPARATION
THE INFORMATION CONTAINED HEREIN IS GIVEN IN GOOD FAITH, BUT NO WARRANTY, EXPRESSED OR
IMPLIED, IS MADE.
DATE PRINTED: April 6, 2006 BY: MILLENNIUM TECHNOLOGIES LTD.
DATE MODIFIED: April 14, 2005 APPROVED BY:
SUPERSEDES: October 1, 2003
24 HOUR PHONE: 403-252-5904
|