Hyperdrill AD 855 & AD 859 Page 2 of 4
TERATOGENICITY: No information available.
REPRODUCTIVE No information available.
TOXICITY:
MUTAGENICTY: No information available.
SYNERGISTIC No information available.
PRODUCTS:
SECTION IV: FIRST AID MEASURES
SKIN CONTACT: Remove contaminated clothing, wash exposed area thoroughly with soap
and water. If irritation persists, obtain medical attention. Launder
contaminated clothing before reuse.
EYE CONTACT: Immediately flush eyes with gently flowing warm water for 15 minutes.
If irritation persists, obtain medical attention.
INGESTION: Do not induce vomiting. If patient is fully conscious give 2 to 4 glasses
of water. If spontaneous vomiting occurs, keep head below hips to
ensure vomitus is not aspirated. Obtain medical attention. Never give
anything by mouth to an unconscious or convulsing victim.
INHALATION: Move patient to fresh air. Apply oxygen or artificial respiration if
required. If breathing difficulties or distress continues obtain medical
attention.
SECTION V: PHYSICAL DATA
APPEARANCE AND ODOUR: Viscous milky white liquid; aliphatic odour
SPECIFIC GRAVITY: 1.04 鈥? 1.06
Not available
BOILING POINT ( C):
Not available
MELTING POINT ( C):
SOLUBILITY IN WATER: Dispersible pH: 6-8 (@ 5 g/L)
PERCENT VOLATILE BY VOLUME: Not available
EVAPORATORTION RATE: Not available
VAPOUR PRESSURE (mmHg): Not available
VAPOUR DENSITY (Air = 1): Not available
BULK DENSITY: Not applicable
SECTION VI: FIRE AND EXPLOSION HAZARD DATA
FLASH POINT: >100 C
FLAMMABLE LIMITS: Not available
EXTINGUISHING MEDIA: Water spray, foam, dry chemical, carbon dioxide
SPECIAL FIRE FIGHTING Self-contained breathing apparatus required for fire
PRODCEDURES: fighting personnel. Remove containers from fire area,
or cool with water spray, if possible.
Hyperdrill AD 855 & AD 859 Page 3 of 4
UNUSUAL FIRE AND Product is not considered flammable, but may burn in
EXPLOSION HAZARDS: a fire situation. Material becomes very slippery when
contacted by water.
SECTION VII: REACTIVITY DATA
STABILITY: STABLE [XX] UNSTABLE [ ]
INCOMPATIBILITY Oxidizing agents may cause exothermic reactions.
(CONDITIONS TO AVOID): Avoid high temperatures, open flames, sparks and all
other sources of ignition.
CONDITIONS OF REACTIVITY: Not available
HAZARDOUS DECOMPOSITION Thermal decomposition may produce oxides of carbon
PRODUCTS: and oxides of nitrogen.
HAZARDOUS POLYMERIZATION: WILL NOT OCCUR [XX] MAY OCCUR [ ]
SECTION VIII: PREVENTATIVE MEASURES
SPECIAL PROTECTION INFORMATION
RESPIRATORY PROTECTION: In case of insufficient ventilation and/or misty
conditions, wear NIOSH approved organic filter
respirator.
VENTILATION: Natural ventilation if adequate in absence of mists.
Use process enclosure, local exhaust ventilation or
other engineering controls if misting occurs.
PROTECTIVE GLOVES: Suggest rubber or viton.
EYE PROTECTION: Suggest safety glasses with side-shields, chemical
goggles and/or face shield. Do not wear contact
lenses.
OTHER PROTECTIVE EQUIPMENT Suggest rubber apron. Ensure eye wash station and
(Specify): safety shower are available.
PRECAUTIONS TO BE TAKEN IN HANDLING AND STORING
Avoid prolonged or repeated skin contact. Minimize breathing vapour or mist. Remove
contaminated clothing; launder or dry-clean before reuse. Remove contaminated shoes and
thoroughly clean before reuse. Cleanse skin thoroughly after contact, before breaks and meals and
at end of work period. Product is readily removed from skin by washing thoroughly with soap
and water. Store in cool and dry location away from incompatibles. Keep container closed when
not in use. Protect from freezing. Freezing will affect the physical condition of the product and
may damage the material. If frozen, the product should be allowed to thaw completely and be
thoroughly mixed before use. This product should be stored in a heated building at a temperature
of 5-35 C. When stored under these conditions the product has a shelf life of approximately six
(6) months. Ensure that stock is rotated.
Hyperdrill AD 855 & AD 859 Page 4 of 4
STEPS TO BE TAKEN IN CASE THE MATERIAL IS SPILLED OR RELEASED
Wear appropriate safety equipment. Eliminate sources of ignition. Stop leak if able to do so
without risk. Dike to prevent spread of material. Collect liquid waste by vacuum to place in an
approved container for disposal. Soak up remaining spill and small spills with absorbent material.
Collect contaminated absorbent in an approved container for disposal. Wash spill site after
material pickup with soap and water.
WASTE DISPOSAL METHOD
Dispose in accordance with federal, provincial and local regulations. It is the responsibility of the
end-user to determine if material meets the criteria of hazardous waste at the time of disposal.
Empty containers must be disposed of, or recycled, in accordance with local regulations.
SECTION IX: PREPARATION
THE INFORMATION CONTAINED HEREIN IS GIVEN IN GOOD FAITH,
BUT NO WARRANTY, EXPRESSED OR IMPLIED, IS MADE.
DATE ISSUED: August 8, 2003 BY: Product safety committee
SUPERSEDES: May 25, 2001
Diversity Technologies Corp. is the parent company of
Canamara-United Supply, Hollimex Products and Canamara SDS.
|