Hyperdrill AF 247 RD
Page 1 of 3
MATERIAL SAFETY DATA SHEET
SECTION I: IDENTIFICATION OF PRODUCT
PRODUCT NAME: HYPERDRILL AF 247 RD
PRODUCT USE: Oil Well Fluid Additive
CHEMICAL FAMILY: Copolymer of Sodium Acrylate and Acrylamide
WORK PLACE HAZARDOUS MATERIALS INFORMATION SYSTEM (WHMIS)
WHMIS CLASSIFICATION: Not A Controlled Product Under WHMIS
WORK PLACE HAZARD: N/A
TRANSPORTATION OF DANGEROUS GOODS (TDG)
SHIPPING NAME: Not Regulated Under TDG
TDG CLASSIFICATION: N/A
UN NUMBER (PIN): N/A
PACKING GROUP: N/A
SECTION II: HAZARDOUS INGREDIENTS
INGREDIENT PERCENT CAS NUMBER LD(50) Oral-Rat OSHA PEL ACGIH TLV
No Hazardous Ingredients
SECTION III: TOXICOLOGICAL PROPERTIES
ROUTE OF ENTRY: [XX] SKIN [XX] EYE CONTACT [XX] INHALATION [XX] INGESTION
EFFECTS OF May cause mild irritation to the eyes, which should cease upon removal of the product. May
OVEREXPOSURE: cause mild irritation of the skin with repeated or prolonged use. The product is non-volatile
but inhalation of dust may cause irritation.
ACUTE EXPOSURE: Contact with the eye may produce irritation and redness. Inhalation of dust may cause
irritation of the respiratory system.
EXPOSURE LIMITS: (8 hr. TWA, total inhalable dust); ACGIH-10 mg/m3;
OSHA PEL-10 mg/m3; and MFRS Recommendation-10 mg/m3
SECTION IV: FIRST AID MEASURES
SKIN CONTACT: In case of skin contact, remove contaminated clothing and wash skin thoroughly with soap
Hyperdrill AF 247 RD
Page 2 of 3
MATERIAL SAFETY DATA SHEET
and water.
EYE CONTACT: If splashed into the eyes, flush with clear water for 15 minutes or until irritation subsides. If
irritation persists, call a physician.
INGESTION: If ingested, do not induce vomiting; remove product from mouth and call a physician.
INHALATION: N/A.
SECTION V: PHYSICAL DATA
APPEARANCE AND ODOUR: Off-white coloured solid
SPECIFIC GRAVITY: 0.65 g/cc
N/A
BOILING POINT (掳C):
N/A
MELTING POINT (掳C):
SOLUBILITY IN WATER: Soluble
PERCENT VOLATILE BY VOLUME: N/A
EVAPORATION RATE: N/A
VAPOUR PRESSURE (mm Hg): N/A
VAPOUR DENSITY (Air = 1): N/A
SECTION VI: FIRE AND EXPLOSION HAZARD DATA
FLASH POINT: None Exhibited
FLAMMABLE LIMITS: N/A
EXTINGUISHING MEDIA: Carbon dioxide, dry chemical, foam, in preference to a water spray.
UNUSUAL FIRE/EXPLOSION HAZARDS: As with most organic powders, flammable dust clouds may be formed
in air. Avoid creating dust. Avoid sources of ignition.
SECTION VII: REACTIVITY DATA
STABILITY: Stable [XX] Unstable [ ]
INCOMPATIBILITY (CONDITIONS TO AVOID): Avoid contact with strong oxidants.
HAZARDOUS DECOMPOSITION PRODUCTS: None known
HAZARDOUS POLYMERIZATION: Will Not Occur [XX] May Occur [ ]
SECTION VIII: PREVENTIVE MEASURES
Hyperdrill AF 247 RD
Page 3 of 3
MATERIAL SAFETY DATA SHEET
SPECIAL PROTECTION INFORMATION
RESPIRATORY PROTECTION: Use dust mask if handling in bulk to prevent inhalation of airborne particles.
VENTILATION: Provide adequate ventilation to minimize dust inhalation.
PROTECTIVE GLOVES: Use gloves, if needed, to avoid prolonged or repeated skin contact.
EYE PROTECTION: Use splash goggles when eye contact may occur.
OTHER PROTECTIVE EQUIPMENT: As necessary to prevent contact.
PRECAUTIONS TO BE TAKEN IN HANDLING AND STORING
Dust generated in handling of this product can be explosive if sufficient quantities are mixed in air in which case
ignition sources should be avoided. Minimize breathing dust. Avoid prolonged or repeated breathing of dust and
contact with skin. Remove contaminated clothing; launder or dry-clean before reuse. Cleanse skin thoroughly after
contact, before breaks and meals and at end of work period. Product is readily removed from skin by washing
thoroughly with soap and water.
STEPS TO BE TAKEN IN CASE THE MATERIAL IS SPILLED OR RELEASED
Sweep up dry and flush spill area with water. Spills of dilute solutions may be flushed with copious amounts of
water, or alternatively, they may be absorbed with an inert material such as earth or speedi-dry and contained for
disposal. The product or its solutions should not be allowed to enter waterways without treatment. Product should
be disposed of in accordance with applicable federal, provincial and local regulations. Spilled solutions can create a
hazard because of their slippery nature.
WASTE DISPOSAL METHOD
The product or its solutions should not be allowed to enter waterways without treatment. Product should be
disposed of in accordance with applicable federal, provincial and local regulations. Spilled solutions can create a
hazard because of their slippery nature.
SECTION IX: PREPARATION
THE INFORMATION CONTAINED HEREIN IS GIVEN IN GOOD FAITH, BUT NO WARRANTY, EXPRESSED OR
IMPLIED, IS MADE.
DATE PRINTED: April 6, 2006 BY: MILLENNIUM TECHNOLOGIES LTD.
DATE MODIFIED: May 28, 2004 APPROVED BY:
SUPERSEDES: October 1, 2003
|